Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for entegris NT 6300
Summary of Contents for entegris NT 6300
- Page 1 P/N 1365 | REV. C 09/20 Proportional ™ Control Valve, Model 6300 User Guide...
-
Page 2: Table Of Contents
Warranty ........21 Unit Operation ......12 Terms and Conditions ....21 Performance ......12 For More Information ....21 Operating Environment ..13 Operation and Use Recommendations ....14 Performance ......15 Operational Reliability .... 15 Entegris, Inc. | User Guide... -
Page 3: Introduction
1.0 and has a setpoint of 0–5 VDC. A 2.5 VDC setpoint signal will adjust the valve to a 0.5 C . A 3.75 VDC setpoint signal will adjust the valve to a 0.75 C User Guide | Entegris, Inc. -
Page 4: Dimensions
19.5 mm (0.77”) 3⁄8” Flaretek 142.2 mm (5.60”) 144.0 mm (5.67”) 19.5 mm (0.77”) 1⁄2” Flaretek 144.5 mm (5.69”) 150.0 mm (5.91”) 21.6 mm (0.85”) 3⁄4” Flaretek 153.6 mm (6.05”) 153.7 mm (6.05”) 27.4 mm (1.07”) Entegris, Inc. | User Guide... - Page 5 114.3 mm (4.50”) 19.5 mm (0.77”) Type Pillar 1⁄2” Super 300 144.5 mm (5.69”) 127.0 mm (5.00”) 21.6 mm (0.85”) Type Pillar 3⁄4” Super 300 153.6 mm (6.05”) 136.1 mm (5.36”) 27.4 mm (1.07”) Type Pillar User Guide | Entegris, Inc.
- Page 6 7 – C 8 ranges Inlet /outlet Dimensions port connection 7 – C 8 ranges 3⁄4” Flaretek 223.4 mm (8.79”) 129.0 mm (5.08”) 24.4 mm (0.96”) 1” Flaretek 223.4 mm (8.79”) 133.6 mm (5.26”) 24.4 mm (0.96”) Entegris, Inc. | User Guide...
- Page 7 6.9 mm (1.10”) (0.27”) 79.2 mm 95.3 mm (3.12”) (3.75”) Figure 4. C 8 range Inlet /outlet Dimensions port connection 8 range 1” Super 300 225.7 mm (8.88”) 146.3 mm (5.76”) 26.7 mm (1.05”) Type Pillar User Guide | Entegris, Inc.
-
Page 8: Installation
Verify the body and the electrical cable are free from mechanical stress from the surrounding equipment. ⁄ ” (M6) ⁄ ” (M6) NOTE: The proportional control valve Flat washer Pan head requires mounting in the direction of the fluid flow. Entegris, Inc. | User Guide... -
Page 9: Mechanical Installation
The 4 – 20 mA input will drop regulated and provide minimum 4.6 V at 20 mA. Input impedance 1.2 ampere (nominal) continuous is 230 ohms. service for each proportional control valve installed. The power supply User Guide | Entegris, Inc. -
Page 10: Electrical Connections
Locating the fuse within the electrical enclosure shared by the power supply enables accessibility for troubleshooting or replacement. Pigtail Cable Entegris, Inc. | User Guide... - Page 11 Setpoint, voltage, 0–10 or 0–5 VDC Setpoint, common Factory use only – do not connect Factory use only – do not connect No connect (NC) No connect (NC) No connect (NC) No connect (NC) No connect (NC) No connect (NC) User Guide | Entegris, Inc.
-
Page 12: Wiring Diagram
For Voltage Setpoints Normally open switch 08-Green/Pin J For valve homing Power supply 01-Red/Pin R 24 VDC ± 10% 02-Black/Pin E — Setpoint control signal 06-Gray/Pin S Electrical cable — 0–5 VDC 07-Pink/Pin G 0–10 VDC Entegris, Inc. | User Guide... -
Page 13: Unit Operation
70 80 90 100 110 120 130 Analog Setpoint Percentage C v 3 F04 / W04 (1⁄2”): Max C v = 1.0 Calculated C v 20 30 40 50 60 70 80 90 100 110 120 130 Analog Setpoint Percentage User Guide | Entegris, Inc. - Page 14 11.0 10.0 20 30 40 50 60 70 80 90 100 110 120 130 Analog Setpoint Percentage * Graph data is representative and each valve needs to be characterized with the application to optimize performance. Entegris, Inc. | User Guide...
-
Page 15: Operating Environment
1 – C 4 range. For C 7 – C range, the system line pressure can be -100 to 550 kPa (-14.5 to 80 psig). Figure 5. Installation and operation example with two on/off valves User Guide | Entegris, Inc. -
Page 16: Performance
9.1 kg (20 lbs.) straight and The maximum response time for 4.5 kg (10 lbs.) at 90 degrees without 1 – 4 is <2 seconds from 5 – 95% being damaged. full scale. The maximum response Entegris, Inc. | User Guide... -
Page 17: Diagnostic Guide
Clear obstruction with back flush/ forward flush procedure. 6. Unit leaks Overpressure on unit Intermittent — single overpressure fluid out of event. Monitor for future instances. weep hole Continuous — diaphragm rupture. Call factory for more information. User Guide | Entegris, Inc. -
Page 18: Maintenance
1. The proportional control valve homing function requires the use of the same 24 VDC ± 10% power source that is used to power the unit. Entegris, Inc. | User Guide... -
Page 19: Reference
* Please consult the factory for pressure ranges from 60 to 80 psig. ** Please consult the factory for temperatures from 65° to 80°C (149° to 176°F). *** For PrimeLock ® connections and other options not listed, please contact Entegris. ELECTRICAL SPECIFICATIONS — 24 VDC ± 10%, regulated... -
Page 20: Ordering Information
1” Super 300 Type Pillar tube fitting Electrical Connector Type FEP- jacketed 12’ pigtail electrical cable PVC-jacketed 1’ electrical cable terminated with 14-pin Turck connector* Setpoint Input Signal K 4–20 mA L 0–10 VDC M 0–5 VDC *14-pin mating cable required for installation Example model number: 6300-CV1-F02-B12-K Entegris, Inc. | User Guide... -
Page 21: Certifications
Repair and warranty service is available at the Entegris factory. Technical Support To expedite the return and repair of the product, contact Entegris at +1 800 394 4084. A Return Materials For technical support, contact the Authorization (RMA) number, MSDS factory at +1 800 394 4084. -
Page 22: Warranty
Entegris’ products are subject to the Entegris, Inc. General Limited Warranty. To view and print this information, visit entegris.com and select the Legal & Trademark Notices link in the footer. Entegris does not warrant any failure in the case of customers using unapproved foreign components. Corporate Headquarters Customer Service 129 Concord Road...
Need help?
Do you have a question about the NT 6300 and is the answer not in the manual?
Questions and answers