Table of Contents
Advertisement
Quick Links
A S S E M B LY I N S T R U C T I O N S
The Devonshire Arbor
Please read through before starting assembly.
IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS.
Check Box for These Contents
In the event of missing or defective parts please call our customer service dept. at 1 800 282 9346 (Mon. to Fri. 8:00 AM to 4:00 PM EST).
1. Rafter End Caps (20)
2. Arch Rafters (10)
3. Arches (4)
4. Arch Couplers (4)
5. Post Trims (4)
6. Keystone Cap (2)
7. Keystone Body (2)
8. Side Panel Curved Top-Rails (2)
9. Side Panel Vertical Spindles - 52.75 (4)
10. Side Panel Vertical Spindles - 51.5 in (4)
11. Side Panel Vertical Spindles - 51 in (2)
12. 1 3/4 in square brackets (4)
13. Side Panel Middle Rail (2)
14. Posts (4)
15. 2 in x 3.5 in Brackets (4)
16. Side Panel Bottom Rails (2)
17. 3/4 in Stainless Steel Screws (32)
18. 1 1/2 in Stainless Steel Screws (16)
19. 3 in Stainless Steel Screws (36)
20. Tubes of Vinyl Glue (2)
Material You Will Need (Not Included)
• 4 in x 4 in x 8 ft Pressure Treated Lumber (4)
Tools You Will Need
• Hammer
• Tape Measure
• Level
• Stool or Short Ladder
• Shovel or Auger
• Cordless Drill
General Information
• Read Instructions through carefully before beginning assembly.
• When assembling components, place on a non-abrasive surface
(i.e. shipping box) to avoid scratching.
• We recommend an area approx 10'x 8' for unobstructed assembling.
• You should not need to use excessive force when assembling components.
85 in
84 in
49 in
59 in
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
www.newenglandarbors.com
84 in
11 in
17
18
19
20
(Not to scale)
24.5 in
34.5 in
1
V1.5/031416
Advertisement
Table of Contents
Related Manuals for New England Arbors The Devonshire Arbor
Summary of Contents for New England Arbors The Devonshire Arbor
- Page 1 A S S E M B LY I N S T R U C T I O N S The Devonshire Arbor www.newenglandarbors.com 85 in 84 in 84 in 49 in 11 in 24.5 in 59 in Please read through before starting assembly.
- Page 2 1 0 7 / 8 Post 3 6 ” Repeat for all four posts. Note the location of the wood posts as they should be symmetrical and opposite to each other. Consult the below diagram for reference. The Devonshire Arbor...
- Page 3 Lay down a second post, align, and insert the panel from the previous step following the same order from step number two. Fasten the rails into its corresponding bracket using the 3/4” screws provided (2 screws per bracket) as shown. insert 1st insert 2nd insert 3rd The Devonshire Arbor...
- Page 4 Flip the arch over and slip each arch couplers into the bottom of the arch. Push firmly until they snap into place. No glue is required for this step. Repeat steps one through five for the second arch. The Devonshire Arbor...
- Page 5 Repeat this step for each end cap. Note: Allow 10 minutes for the vinyl glue to set before lifting or moving the arch assembly. Note: Avoid the guide pin when fastening the screw. The Devonshire Arbor...
- Page 6 Carefully move the side panels into the excavated holes. (Measurements shown are inside to inside of posts) Run a 2” - 3” long bead of glue on the ribbed flanged of the arch couplers as shown. 36 in. 91.4 cm. 12 in. 30.5 cm. The Devonshire Arbor...
- Page 7 S T E P F I V E Place the arch assembly over and into the side panel posts. (You will need a helper). Run a bead of glue around the post just under the arches. Slide the post trims up and hold them in place momentarily to allow the glue to set.
Need help?
Do you have a question about the The Devonshire Arbor and is the answer not in the manual?
Questions and answers