Advertisement
MAINTENANCE & CLEANING
Interior parts
Dismantle all shelfs, door frames, trays, covers and drawers
and clean with a soft cloth that is soaked with water or medium
detergent (for bowl or chopstick wash).If detergent is used,
please clean with water first,then wipe with a piece of dry cloth.
Door gasket
If the door gasket contacts the oil or sauce etc.,it will be
impaired after a long time, especially for the gasket of the
door up and down.Make sure to cleanthe gasket carefully.
The recess shall be cleaned by the chopstick shrouded by
cotton piece.When embed the gasket, fit four corners first
and embed the gaskets section by section.
Defrost method
When the frost layer gets thick, it may impair the cooling effect. You may take out and pack
the foods. Pull out the power plug and wipe off the water with soft cloth when the frost layer
vanishes. Then connect to the power and restart the appliance to setup the temperature.
Generally once or twice defrost is required per year.
NOTES
1.Plug off the power first, then clean the freezer after defrost;
2.The best time to defrost is when the freezer is empty or half empty;
3.Do not use metal or sharp tools for defrost to prevent damage;
4.No electric heater is allowed for defrost;
Cleaning precautions
Pull out the plug from the socket before cleaning, the interval between
plug in and out shall be over 5 minutes;
No water is allowed in the lamp and PCB cover during cleaning;
Wipe with soft towel dipped over water or medium detergent, then clean
with dry cloth;
Do not use the detergent with abrasive(e.g. Toothpaste),acid,chemical
solvent(e.g.alochol) or putty agent.
The following checks shall be made after maintenance:
NOTES
Any chaps or scars are found on the power cord.
Plug in the socket reliably
The power plug gets hot or other accidents.
WARNING
- Keep ventilation openings, in the appliance enclosure or in the build-in structure,
clear of obstruction.
- Do not use mechanical devices or other means to accelerate the defrosting process,
other than those recommended by the manufacturer.
- Do not damage the refrigerant circuit.
- Do not use electrical appliances inside the food storage compartments of the
appliance, unless they are of the type recommended by the manufacturer.
8
Change the lamp
Plug out the power cord.
Screw off the lamp cover, then hold the cover and pull left to remove the cover.
Turn off the bulb counterclockwise.
Turn on the bulb clockwise.
Push the right side of the lamp cover into the left recess of the temperature
controller, then turn on the screws.
Bulb parameters: ~220V-240V,25W,E14
INSTALLATION & SETUP
Place the refrigerator
1.Remove the foot cushion prior to use.
2.If the appliance is placed unsteadily, you may adjust the front leg in the bottom to stablize
the appliance (lift by turning left).There is a adjust hole in the front leg.You may adjust it
with a crosshead screwdriver (see right figure).
3.The ground under the appliance shall be flat and solid.
Otherwise noise and oscillation will arise.
The noise will grow stronger if the
appliance is put on the soft ground;
Please put a solid plate on the blanket,
to avoid miscolor or heat blocking;
To stablize the appliance, please leave
the foot contacting the ground closely and
keep the appliance leaning back for easy closing of the door.;
Packaging & handling
1.Unpacking, repacking and handling
Do remember where the packages are during unpacking and examining.
The products can not be transported until they are repacked after examining.
2.Do not hold the door during transportation.
3.Avoid clash or acute shaking during handling.
4.Vertical handling to avoid clash
Do not position the appliance reversely or horizontally.
If tilting is required, the tilting angle shall be less than45
Please handle the appliance as per the instructions to
prevent from noise or some other problems.
45
5
Advertisement
