Advertisement
!
Safety Instructions
To avoid fire, shock, and serious personal injury, follow all instructions carefully.
1. Read your Owner's Manual carefully before installing the light fixture. Retain Owner's Manual for
future reference.
2. Be careful of the fan and blades when cleaning, painting, or working near the fan. Before
installing or servicing the light fixture or ceiling fan, switch power off at service panel and lock
service panel disconnecting means to prevent power from being switched on accidentally. When
the service disconnecting means cannot be locked, securely fasten a warning device, such as a
tag, to the service panel.
3. Do not exceed the wattage indicated on fixture (Two 50-watt mini-candelabra base halogen bulbs).
ADDITIONAL SAFETY INSTRUCTIONS FOR INSTALLATION
1. To avoid possible electrical shock be sure electricity is turned off at the main fuse or circuit
breaker box before wiring.
2. The installation is to be in accordance with the National Electrical Code, ANSI/NFPA 70-2008 and
Local Codes. Use the National Electrical Code if Local Codes do not exist. The ceiling fan must be
grounded as a precaution against possible electrical shock. Electrical installation should be made
or approved by a licensed electrician.
3. Make certain no bare wires are exposed outside the wire connectors.
4. All wiring must conform to national and local electrical codes.
5. Follow the recommended instructions for the proper method of wiring your new light fixture. If
you feel you do not have enough electrical wiring knowledge or experience, have your light
fixture installed by a licensed electrician. Any electrical work not described in this manual should
be performed by a licensed electrician.
WARNING: To reduce the risk of possible fire and electrical shock, install only on Emerson Model
CF130.
Assembly and Installation
!
WARNING
Do not install or use the light fixture if any
part is missing or damaged. Call toll-free:
1-800-654-3545
!
WARNING
To avoid possible electrical shock, be
sure electricity is turned off at the main
fuse or circuit breaker box before wiring.
Parts Included: 1 Glass Bowl, 1 Light Fitter,
3 Outer Bowl Caps, 3 Finial Nuts, 2 50-Watt
Mini-Candelabra Base Halogen Bulbs, 2 Wire
Connectors, 2 Pendants, 1 Lockwasher, 1 Hex
Nut and 2 Pull Chains.
Installation on Emerson Fans
Having a Modular Switch Cup
with Center Screw
1. Remove all parts and parts packages from
the carton.
2. Remove the switch cup(1) from the cover
plate(2) by removing the three screws(3)
around the side of the switch cup (Figure 1).
WARNING
3. Disconnect the motor connector(4) from the
switch cup connector(5) (Figure 1).
4. Remove the center screw(6) from the switch
cup (Figure 1).
5. Carefully locate the white and blue wires
(labeled either "L" or "LIGHT") in the switch
cup and remove the wire connectors from
the wires.
6. Insert the black and white wires from the
light fitter(7) through the center hole in the
switch cup (Figure 2) and thread the switch
cup onto the light fitter. Hold wires taut while
installing switch cup to prevent the wires
from twisting.
(2) COVER PLATE
(4) MOTOR
CONNECTOR
(5) SWITCH CUP
(3) SCREWS
(1) SWITCH
CUP
(6) CENTER SCREW
Figure 1
2
7. Insert the black and white wires through the
lockwasher(8) and hex nut(9) supplied.
Firmly tighten the hex nut to secure the light
kit fitter to the switch cup.
8. Connect the white wire from the switch cup to
the white wire of the light fitter (Figure 2).
Connect the blue wire from the switch cup to
the black wire of the light fitter. Use the wire
connectors provided with the light kit to make
the electrical connections (Figures 2 and 3).
(4) MOTOR
CONNECTOR
BLACK WIRE
BLUE WIRE
(9) HEX NUT
(3) SCREWS
(1) SWITCH
CUP
OUTER BOWL
CAP
Figure 2
!
To avoid possible fire or electrical shock,
make certain no bare wire strands are
exposed outside wire connectors.
Figure 3
9. Carefully tuck all wires and splices into the
switch cup(1). (Figure 2.)
10. Connect the motor connector(4) to the
switch cup connector(5).
11. Position the switch cup(1) and fitter
assembly(7) on the cover plate(2) and
install the three screws(3) that were
previously removed in Step 2 and tighten
securely.
CONNECTOR
12. Proceed to "Installation of Glass Bowl"
section.
!
To avoid possible fire or electric shock,
be careful not to pinch wires between
switch cup and the cover plate.
Installation on Emerson Fans
Having Two-Piece Die-Cast
1. Remove all parts and parts packages from
carton.
2. Remove the cover(5) from the fan switch
housing(1) by removing the two outer
screws(2). (See Figure 4).
FAN SWITCH
CHAIN
(2) COVER PLATE
(5) SWITCH CUP
CONNECTOR
BLUE WIRE
(6) WIRE
CONNECTOR
BLACK WIRE
WHITE WIRES
(8) LOCKWASHER
(5) COVER
FAN SWITCH
(2) SCREWS
CHAIN
(7) LIGHT FITTER
Figure 4
BOWL CAP
3. Remove the center screw(4) from the
FAN SWITCH CHAIN
cover(5). Insert the black and white wires
(WHERE APPLICABLE)
from the light kit fitter(6) through the hole
and thread the switch housing cover tightly
onto the light kit fitter.
WARNING
4. Insert the black and white wires through the
lockwasher(8) and hex nut(9) supplied.
Firmly tighten the hex nut to secure the light
kit fitter to the switch housing cover(5).
5. Carefully locate the white and blue wires
(labeled either "L" or "LIGHT") in the switch
housing and remove the wire connectors(3)
from the wires.
6. Connect the white wire from the ceiling fan
to the white wire of the light kit fitter(6).
Connect the blue wire from the ceiling fan to
the black wire of the light kit fitter. Use the
wire connectors provided with the light kit to
make the electrical connections (Figures 4
and 5.)
7. Carefully tuck all wires and splices into the
switch housing(1).
8. Attach the cover/light fitter(5)(6) to the switch
WARNING
To avoid possible fire or electrical shock,
make certain no bare wire strands are
exposed outside wire connectors.
Figure 5
3
Switch Housings
(1) SWITCH
HOUSING ASSEMBLY
WHITE WIRE
(3) WIRE
CONNECTORS
WHITE WIRE
(9) HEX NUT
(8) LOCKWASHER
(4) CENTER
SCREW
(6) LIGHT FITTER
(7) BOWL CAP
!
WARNING
Advertisement
