Download Print this page
Behringer SYSTEM 100 172 PHASE SHIFTER/DELAY/LFO Quick Start Manual

Behringer SYSTEM 100 172 PHASE SHIFTER/DELAY/LFO Quick Start Manual

Legendary analog phase shifter/ delay/lfo module for eurorack
Hide thumbs Also See for SYSTEM 100 172 PHASE SHIFTER/DELAY/LFO:

Advertisement

Quick Links

Quick Start Guide
SYSTEM 100
172 PHASE SHIFTER/
DELAY/LFO
Legendary Analog Phase Shifter/
Delay/LFO Module for Eurorack
Controls
(3)
(1)
(2)
(8)
(9)
(10)
(11)
CV IN – Accepts voltage from an external source to
(1)
control or modulate the phase shifter frequency or audio
delay time. If no jack is inserted the LFO can be used to
modulate the effect.
MOD INTENSITY – Controls how much the effect is
(2)
modulated by the LFO or external CV input.
EFFECT ON/OFF – Engages or disengages the
(3)
effect section.
SHIFT FREQ – Adjusts the frequency of the phase shifter.
(4)
SIG IN – Accepts an incoming signal via 3.5 mm TS cable.
(5)
SIG OUT – Sends the signal from the effect section.
(6)
(4)
(5)
(6)
(7)
(12)
(13)
(14)
RESONANCE – Adjusts the amount of signal that is fed
(7)
back through the effect.
DELAY TIME – Adjusts the time of the delay effect.
(8)
FREQUENCY – Controls the LFO output frequency.
(9)
LFO OUT – Sends the LFO signal as a triangle and inverted
(10)
triangle wave.
THRESHOLD – Controls the input voltage level required to
(11)
trigger the gate.
GATE IN – Accepts an incoming gate signal via 3.5 mm
(12)
TS cable.
GATE OUT – Send the gate delay signal via 3.5 mm
(13)
TS cable.
GATE TIME – Controls the gate length.
(14)
Power Connection
The module comes with the required power cable for connecting
to a standard Eurorack power supply system. Follow these
steps to connect power to the module. It is easier to make
these connections before the module has been mounted into
a rack case.
1.
Turn the power supply or rack case power off and
disconnect the power cable.
2.
Insert the 16-pin connector on the power cable into the
socket on the power supply or rack case. The connector has
a tab that will align with the gap in the socket, so it cannot
be inserted incorrectly. If the power supply does not have
a keyed socket, be sure to orient pin 1 (-12 V) with the red
stripe on the cable.
3.
Insert the 10-pin connector into the socket on the back of
the module. The connector has a tab that will align with the
socket for correct orientation.
4.
After both ends of the power cable have been securely
attached, you may mount the module in a case and turn on
the power supply.

Advertisement

loading
Need help?

Need help?

Do you have a question about the SYSTEM 100 172 PHASE SHIFTER/DELAY/LFO and is the answer not in the manual?

Questions and answers

Summary of Contents for Behringer SYSTEM 100 172 PHASE SHIFTER/DELAY/LFO

  • Page 1 Quick Start Guide SYSTEM 100 RESONANCE – Adjusts the amount of signal that is fed back through the effect. 172 PHASE SHIFTER/ DELAY TIME – Adjusts the time of the delay effect. DELAY/LFO FREQUENCY – Controls the LFO output frequency. LFO OUT –...
  • Page 2 3.5 mm TS jack, DC coupled property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Impedance 47 kΩ, unbalanced Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Auratone Max input level +10 V and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd.