Subscribe to Our Youtube Channel
Related Manuals for HDanywhere XTND4K14140TPC
Summary of Contents for HDanywhere XTND4K14140TPC
- Page 1 XTND 4K (40) TPC Splitter (1x4+1) CODE: XTND4K14140TPC Product Guide (English UK) Revision 1: 28/08/20...
- Page 2 EDID switch positions & connecting over USB 12-13 IR (Infrared) control, Testing IR works 14-15 Cabling 16-17 Example wiring diagram, Power up sequence 18-19 2 Year Product Guarantee 20-21 Conformity, Hire a HDA Pro 22-23 Help is only an email away: support@hdanywhere.com.
-
Page 3: Glossary Of Terms
Glossary of terms EDID comes from your display and is bundled in with HDMI picture and audio data. EDID tells the HDMI source what resolution the display can handle and what audio format it can play. EDID Extended Display Identification Data is not normally an issue when connecting a source directly to display. - Page 4 Infrared Transmitter cable (1.5m) (IR TX) Infrared (20-60Khz) Receiver cable (1.5m) (IR RX) 12V 2.5A Power Supply with adapters (UK,EU,US,AU) Mounting Kits User Manual Help is only an email away: support@hdanywhere.com.
- Page 5 Features Supports 18Gbps bandwidth and video picture formats up to 4K@60Hz (4:4:4) including HDR and Dolby Vision* Includes local HDMI loop out 4K up to 40m (131ft) Digital audio support up to and including Dolby Atmos and DTS:X Audio extraction over coax & stereo (source audio only - no downmix). Backwards IR EDID management Power over Cable...
-
Page 6: Specifications
PCM 2.0 / 5.1 / 7.1, Dolby Digital / Plus / EX / True HD / Atmos, DTS, DTS-EX, DTS-96 / 24, DTS High HDMI audio formats Res, DTS-HD Master Audio, DTS-X Coax audio formats PCM 2.0, Dolby Digital / Plus / DTS 2.0 /5.1 Stereo audio formats PCM 2.0 Help is only an email away: support@hdanywhere.com. - Page 7 Infrared 20Khz - 60Khz ±8kV (Air-gap discharge) ESD protection ±4kV (Contact discharge) Power consumption 14W (Maximum) Power supply 12V 2.5A Operating temperature 0°C - 40°C / 32°F - 104°F Storage temperature -20°C - 60°C / -4°F - 140°F Relative humidity 20 - 90% (Non-condensing) Housing Steel...
-
Page 8: Transmitter Diagram
Transmitter Diagram Video Coax / Stereo (OUT) Source (IN) HDMI (OUT) IR (OUT) DC12V Help is only an email away: support@hdanywhere.com. - Page 9 Description 1. Power Switch: Turns the XTND on/off. 2. Power: Indicator light. If this light is on and solid then the XTND has power. 3. HDMI Status: The left light indicates an active HDMI source is connected if on. The right light indicates an active display is connected if on.
-
Page 10: Receiver Diagram
Receiver Diagram Help is only an email away: support@hdanywhere.com. - Page 11 Description 1. HDMI (OUT): HDMI video output. Connect to your display to provide a picture. 2. DC12V: Unused. 3. IR (IN): Connect an IR RX to the “IR IN” port to receive an IR command from a remote control to pass through to the XTND transmitter. 4.
- Page 12 10101 4K2K30Hz_444, Dolby/DTS 5.1 00111 Copy from Output C 10100 4K2K30Hz_444, HD Audio 7.1 00110 Copy from Output D 10011 4K2K60Hz_420, Stereo Audio 2.0 00000 Disable dip switch EDID 10010 4K2K60Hz_420, Dolby/DTS 5.1 Help is only an email away: support@hdanywhere.com.
-
Page 13: Connecting Over Usb
“Service” port on the side of the XTND and open a serial command tool on your computer. Baud rate: 115200 Data bits: Stop bit: Check bit: The API is available from our support site or by emailing support@hdanywhere.com... - Page 14 3. Connect an IR RX to port labelled “IR (IN)” on the XTND 1.5m receiver. 4. Place IR RX in line-of-sight of the remote control. Ground Power Power Signal Signal Help is only an email away: support@hdanywhere.com.
- Page 15 Testing that IR works This section aims to verify that your XTND’ s IR control system is setup correctly and assumes that all other setup has been followed as per the instructions laid out in this manual. Please refer to the XTND wiring diagrams in this document to ensure that your setup matches that before proceeding with the verification below.
- Page 16 If patch panels are terminated correctly then there is a minimal loss of distance. The use of wallplates and patch panels has the potential to cause increased resistance on the cable introducing pinch points for signal transmission and could reduce transmission lengths. TIP: Instead of using RJ45 wallplates use brush plates. Help is only an email away: support@hdanywhere.com.
- Page 17 HDMI cabling HDANYWHERE recommends using suitably robust and good quality HDMI cables. It is not advised to use passive HDMI cables over 5 metres in length either on the inputs or the outputs of the XTND system. Where HDMI cables longer than 5 metres are required, HDA...
-
Page 18: Example Wiring Diagram
If you are unsure how you Coax Cat Cable might install this device in to your property then contact support@ IR RX/TX Cable hdanywhere.com or contact a HDA Pro (https://hdanywhere.com/ Speaker Cable dealers-and-installers/) for further assistance. Help is only an email away: support@hdanywhere.com. -
Page 19: Power-Up Sequence
Power up sequence Ensure that all devices are turned off. Connect HDMI source to “HDMI (IN)” port on the XTND transmitter. Connect the XTND transmitter and receiver together by using Cat 6/7 cable connected to the each end of the “Video TPC” port. Connect a display to the “HDMI (OUT)”... -
Page 20: Year Guarantee
OUR GUARANTEE TO YOU 2. We, HDANYWHERE warrant to you, the end user of the HDA hardware (the “Products”) that on the date of delivery of the Products to you, and for a period of 2 years from that date of delivery, the Products shall: (a) match any description that has been provided to you;... - Page 21 GUARANTEE CONTACT INFORMATION To contact (support@hdanywhere.com) or call HDANYWHERE Technical Support (call charges will depend on your telephone provider. Please check with your operator for exact charges).The team is available 9am - 5pm weekdays. To help us handle your query promptly, please have your invoice number and model SKU and serial ready.
- Page 22 Important information EU Conformity Hereby, HDANYWHERE declares that this HDMI connectivity device is in compliance with the essential requirements and other relevant provisions of the following Directives: 2006/95/EC (LVD Directive); 2004/108/EC (EMC Directive); 1999/5/EC (R&TTE Directive). The full text of the EU declaration of conformity is available in the compliance section at HDANYWHERE.com/legals Recycling your device properly In some areas, the disposal of certain electronic devices is regulated.
- Page 23 If cabling infrastructure, installation and control seem like too much to absorb and learn then why not hire a HDA Pro to do the work instead for you? Having your XTND system professionally installed should help to guarantee the system’ s long-term performance and ensure that it blends neatly with your decor. Find a HDA Pro anywhere in the world today https://hdanywhere.com/dealers-and-installers/...
- Page 24 Registered in England & Wales 06046737 VAT 913222367 HDANYWHERE assumes no responsibility for any inaccuracies that may be contained in this document. In no event will HDANYWHERE be liable for direct, indirect, special, incidental, or consequential damages resulting from any...
Need help?
Do you have a question about the XTND4K14140TPC and is the answer not in the manual?
Questions and answers