Download  Print this page

Samsung SyncMaster 320MX User Manual

Hide thumbs

Advertisement

Table of Contents
SyncMaster 320MX,320MXN

LCD Monitor

User Manual

Advertisement

Table of Contents

   Summary of Contents for Samsung SyncMaster 320MX

  • Page 1: Lcd Monitor

    SyncMaster 320MX,320MXN LCD Monitor User Manual...
  • Page 2: Safety Instructions

    Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.
  • Page 3 Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Do not connect multiple appliances to the same power outlet. • Do not disconnect the power cord while using the product. •...
  • Page 4 Do not install it in a badly ventilated location such as a bookcase or closet. • When putting the product down, make sure to put it down softly. • Do not place the front of the product on the floor. •...
  • Page 5 When cleaning the product, make sure to disconnect the power cord. • When cleaning the product, disconnect the power cord and clean it softly with a dry cloth. • Since the product housing is easily scratched, make sure to use the specified cloth only.
  • Page 6 Safety Instructions Do not try to move the monitor by pulling only the wire or the signal cable. • Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable. Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables.
  • Page 7 Safety Instructions Take a rest for at least five (5) minutes after using the monitor for one (1) hour. This reduces the weariness of your eyes. Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations.
  • Page 8 Safety Instructions Do not place the product in a location exposed to direct sunlight or near any heat such as a fire or heater. • This may reduce the lifetime of the product, and may result in fire. Do not drop any objects onto the product or cause any impact to the product.
  • Page 9: Package Contents

    Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Note This stand is not for the Floor Standing Type. Unpacking Manuals Quick Setup Guide...
  • Page 10 Others Remote Control Sold separately DVI Cable TV tuner box Note • You can purchase and connect a separate network box or TV tuner box. For information on how to use these, refer to their respective user manuals. • You can only connect one external box. Your LCD Display Front MENU button [MENU]...
  • Page 11 Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Navigate buttons (Up-Down buttons) Moves from one menu item to another vertically or adjusts selected menu values. Adjust buttons (Left-Right buttons) / Volume buttons Moves from one menu item to another horizontally or adjusts selected menu val- ues.
  • Page 12 Introduction POWER S/W ON [ │ ] / OFF [O] Switches the LCD Display On/Off. POWER IN The power cord plugs into the LCD Display and the wall plug. RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port DVI / PC / HDMI IN [DVI/PC/HDMI AUDIO IN] (PC/DVI/HDMI Audio Connection Terminal (Input)) DVI / PC / HDMI IN [HDMI]...
  • Page 13 Introduction DC POWER OUT [Power] Connect this to the POWER connector of a TV tuner box or network box. AV IN [VIDEO] (VIDEO Connection Termi- nal) Connect the [ VIDEO ] terminal of your monitor to the video output terminal of the external device using a VIDEO cable.
  • Page 14: Remote Control

    Note See Connecting Cables for further information regarding cable connections. Remote Control Note The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display , causing a malfunction due to interference with the frequency. Introduction Kensington Lock The Kensington Lock is a device used to physi-...
  • Page 15 POWER 3. Number Buttons Introduction POWER Number Buttons button + VOL - MUTE TV/DTV MENU INFO COLOR BUTTONS TTX/MIX STILL AUTO S.MODE LOCK SOURCE ENTER/PRE-CH CH/P D.MENU GUIDE RETURN Up-Down Left-Right buttons EXIT MagicInfo P.MODE DUAL/MTS SWAP Turns the product On. Turns the product Off.
  • Page 16 4. DEL button 5. + VOL - MUTE 7. TV/DTV MENU INFO 11.COLOR BUTTONS TTX/MIX 13.STILL 14.AUTO 15. S.MODE 16.MDC 17.LOCK SOURCE ENTER/PRE-CH 20. CH/P 21.D.MENU 22.GUIDE RETURN Introduction The "-" button operates only for DTV. It is used to select MMS (multi-channel) for a DTV.
  • Page 17 24. Up-Down Left-Right but- tons EXIT 27.MagicInfo 28. P.MODE DUAL/MTS 30. PIP 31.SWAP Mechanical Layout Mechanical Layout Introduction Moves from one menu item to another horizontally, vertically or adjusts selected menu values. Exits from the menu screen. Not Available. MagicInfo Quick Launch Button. When you press this button, current picture mode is displayed on the lower center of the screen.
  • Page 18 Introduction...
  • Page 19: Installation Vesa Bracket

    Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket. • At least 2 persons are needed in order to move the LCD Display. • SAMSUNG is not responsible for any product damage or any injury caused by installation at customer's discretion. Introduction...
  • Page 20: Wall Bracket Installation

    • Contact a technician for installing the wall bracket. • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.
  • Page 21: Wall Bracket Assembly

    Wall Bracket Assembly Note There are two hinges(left and right). Use the correct one. Insert and tighten the Captive Screw in the direction of the arrow. When done, mount the wall bracket on the wall. There are two hinges(left and right). Use the correct one. Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct.
  • Page 22: To Mount The Product On The Wall Bracket

    Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each of the brackets and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws A. To mount the product on the wall bracket The shape of the product may vary depending on the model.
  • Page 23: Wall Bracket Angle Adjustment

    Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket. Wall Bracket Angle Adjustment Adjust the bracket angle to -2°...
  • Page 24 Introduction Make sure to use the top center, and not the leftor the right side of the product to adjust the angle.
  • Page 25: Connecting A Computer

    Connections Connecting a Computer Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un- wiring the earth lead, make sure to disconnect the AC power in advance. Note AV input devices such as DVD players, VCR's or camcorders as well as your computer can be con- nected to the LCD Display.
  • Page 26: Connecting To Other Devices

    Turn on both your computer and the LCD Display. • The DVI cable is optional. • Contact a local SAMSUNG Electronics Service Center to buy optional items. Connecting to Other devices Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power.
  • Page 27: Connecting To A Camcorder

    Connecting to a Camcorder Locate the A/V output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the AV AUDIO IN [L-AUDIO-R] on the LCD Display . Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the AV IN [VIDEO] on the LCD Display .
  • Page 28: Connecting Using A Dvi To Hdmi Cable

    Connecting Using a DVI to HDMI Cable Note • Connect the DVI output terminal of a digital output device to the HDMI terminal of the LCD Display using a DVI to HDMI cable. • Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored audio output terminals of the digital output device, and connect the opposite jack to the DVI / PC / HDMI AUDIO IN terminal of the LCD Display.
  • Page 29: Connecting A Usb Device

    Note Connect the LAN cable. (Applicable to the MXn model only) Connecting a USB device Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un- wiring the earth lead, make sure to disconnect the AC power in advance.
  • Page 30: Using The Software

    Using the Software Installation MagicInfo Pro Installation Insert CD into the CD-ROM drive. Click the MagicInfo Pro installation file. When the Install Shield Wizard window appears, click "Next." Select "I agree to the terms of the license agreement" to accept the terms of use. You are required to log in to the MagicInfo Pro Server program.
  • Page 31 Choose a folder to install the MagicInfo Pro program. Click "Install." Using the Software...
  • Page 32 The "Installation Status" window appears. It is recommended restarting the system for the normal operation of the MagicInfo Pro Server program. Click "Finish". Using the Software...
  • Page 33: System Requirements

    10. When the installation is complete, the MagicInfo Pro executable icon appears on your desktop. 11. Double-click the icon to start the program. System Requirements Minimum P1.8 Recommen- P3.0GHz Using the Software Ethernet 256M 100M/1G Windows XP Windows 512M 2000 (Serv- ice Pack 4) Application WMP 9 or...
  • Page 34: Main Screen

    Therefore, a serial cable should be connected between the serial port on a PC and the serial port on a display. Main Screen Click Start > Program > Samsung > MDC System to start the program. Select a set to see the volume of the selected set within the slider.
  • Page 35: Port Selection

    Main Icons Remocon Safety Lock Port Selection 1. Use the main icons to switch into each screen. 2. Allows you to enable or disable the remote control signal receiving function of the display unit. 3. Set the Safety Lock function. When setting the Lock function, you can only operate power and lock buttons on the remote control and set.
  • Page 36: Power Control

    1. The Multiple Display Control is originally set to COM1. 2. If any port other than COM1 is used, COM1 through COM4 can be selected in the Port Selection Menu. 3. If the exact port name that is connected to the LCD Display using a serial cable is not selected, communication will be unavailable.
  • Page 37 Info Grid shows some basic information necessary to Power Control. (Power Status) 2) Input 3) Image Size 4) On Timer 5) Off Timer 2. Use the Select All button or Check Box to choose a display to control. Power Control allows controlling some of the functions of the selected display. 1) Power On/Off...
  • Page 38: Input Source

    - Turns the power of the selected display On/Off. 2) Volume - Controls the volume level of the selected display. It receives the volume value of the selected display from the sets and displays it in the slider. (When you cancel the selection or choose Select All, the value returns to the default value 10) (Mute On/Off) - Turns on/off the Mute function of the selected display.
  • Page 39: Image Size

    Info Grid shows some basic information necessary to Input Source Control. - Changes the Input Source of the selected display to PC. - Changes the Input Source of the selected display to BNC. - Changes the Input Source of the selected display to DVI. - Changes the Input Source of the selected display to TV.
  • Page 40 Info Grid shows some basic information necessary to Image Size Control. ( Power Status) - Shows the power status of the current display. 2) Image Size - Shows the current Image Size of the display in use. 3) Input - Shows the current Input Source of the display in use. 4) Info Grid displays only the displays whose Input Source is PC, BNC, DVI.
  • Page 41 Info Grid shows some basic information necessary to Image Size Control. 1) Click the Video Source tab to adjust Image Size for TV, AV, S-Video, Component, DVI(HDCP), HDMI, DTV. Click Select All or use Check Box to select a display to control. 2) Info Grid displays only the display having TV, AV, S-Video, Component or DVI(HDCP) as input source.
  • Page 42: Pip Size

    Info Grid shows some basic information necessary to Time Control. 1) Current Time - Set the current time for the selected display (PC Time). - To change the current time, first change the PC Time. 2) On Time Setup - Set the Hour, Minute, AM/PM of On Time Setup, Status, Source, Volume of the selected display. 3) Off Time Setup - Set the Hour, Minute, and AM/PM, Status for Off Time Setup of the selected display.
  • Page 43: Pip Source

    Info Grid shows some basic information necessary to PIP Size Control. 1) PIP Size - Shows the current PIP Size of the display in use. 2) OFF - Turns off the PIP of the selected display. 3) Large - Turns on the PIP of the selected display and changes the size to Large. 4) Small - Turns on the PIP of the selected display and changes the size to Small.
  • Page 44 Info Grid shows some basic information necessary to PIP Source Control. 1) PIP Source - PIP Source can be controlled with turning on the LCD Display power. 2) PC - Changes the source of the PIP of the selected display to PC. 3) BNC - Changes the source of the PIP of the selected display to BNC.
  • Page 45: Picture Pc

    Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide.When selected, each function fetches the value for the set and displays it on the slide bar. When "Select All" is chosen, the default value is displayed.
  • Page 46 1. Click Settings of the main icons and the Settings Control screen appears. Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide. When selected, each function fetches the value for the set and displays it on the slide bar.
  • Page 47: Image Lock

    Audio 1. Click Settings of the main icons and the Settings Control screen appears. Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide. When selected, each function fetches the value for the set and displays it on the slide bar.
  • Page 48: Lamp Control

    Info Grid shows some basic information necessary to Settings Control. 1) Image Lock - Available only for PC, BNC. 2) Coarse - Adjusts Coarse of the selected display. 3) Fine - Adjusts Fine of the selected display. 4) Position - Adjusts Position of the selected display. 5) Auto Adjustment - Self-Adjust to the incoming PC signal.
  • Page 49 An "Info Grid" showing several basic data items appears. 1) Maintenance - Allows the Maintenance Control function for all input sources. 2) Auto Lamp Control - Automatically adjusts the backlight of the selected display at a specified time. The Manual Lamp Control automatically turns off if you adjust using the Auto Lamp Control. 3) Manual Lamp Control - Allows you to adjust the backlight of the selected display regardless of the time.
  • Page 50: Video Wall

    1) Safety Screen - Eliminates the afterimages that can result when the selected display stays in Pause mode for an extended period of time. You can set the repeat cycle timer by selecting the "Interval" by hour and "Second" by second. It can be set to Scroll, Pixel, Bar and Eraser by Screen Type.
  • Page 51 Select a display from Display Selection. The place will be set up by pressing a number in the selected mode. The MDC program supplied by Samsung supports up to 5x5 LCD Displayes. 3) On / Off - Turns on/off the Video Wall function of the selected display.
  • Page 52: Settings Value Display In Multiple Display Mode

    - Check the displays to see if any of the other displays connected have the same ID. If more than one displays have the same ID, those displays are not properly detected by the program due to data conflict. - Check if the Display Set ID is a number between 0 and 25. (Adjust using the Display menu) Note : A Display Set ID must be a value between 0 and 25 .
  • Page 53: What Is Magicinfo Pro

    What is MagicInfo Pro? Using MagicInfo Pro Remote Management Message What is MagicInfo Pro? MagicInfo Pro uses an Ethernet network for servers and monitors, and transfers media files (image files, music files, and movies) and office files (HTML, PDF) from the server to the monitors over the network.
  • Page 54 schedules. 5. Instants message → You can display a message on selected monitors regardless of schedules. 6. MDC and System → The MDC and System functions allow you to control, view the status of, and diagnose monitors. 7. VNC → The VNC function allows you to connect to a monitor remotely and view the status of and control and diagnose it.
  • Page 55 What is MagicInfo Pro? Using MagicInfo Pro Remote Management Message Using MagicInfo Pro Running MagicInfo Pro 1. Click Programs -> MagicInfo Pro -> MagicInfo Pro. 2. When MagicInfo Pro runs, select Log In from the File menu. 3. Enter the user name and password and click OK. If you log in for the first time, select 'Administrator' as enter the user name and the password you set when installing the program.
  • Page 56 2. Configure the Network Connection settings In the General tab. Enter the server name on the monitor identical to the name of the server. To change the server name, double-click the Value field of the Server Name item. 3. If there is more than one network card in the server, select a network card in the Network Device item.
  • Page 57 MagicInfo in the OSD pages.) 2. A message is displayed to notify that the monitor is successfully connected to the server. File Sub-Menus Registering a Library 1. Select Library from the File menu to open the Library View. 2. Select a photo file, music file, movie file, document, or Flash file etc. on the server. 3.
  • Page 58 4. The registered library files are used by the monitor when the Operating Mode of the monitor is set to Player or is used when registering a screen. Registering a Screen 1. Select Screen from the File menu to open a Screen View. 2.
  • Page 59 5. Repeat steps 2 to 4 to register other areas on a screen. 6. After finishing registering areas, select Save from the File menu to save the screen. 7. Register a schedule to display the saved screen on a monitor(s). Registering a Schedule 1.
  • Page 60 4. If you want to change the date or time of the schedule, drag it to a different date or time. 5. Select Publish from the Tools menu. Select the checkbox next to the monitors for which you want to register the selected schedule.
  • Page 62 What is MagicInfo Pro? Using MagicInfo Pro Remote Management Message Library File Menu Library / Screen / Schedule / Remote Management / Message Creates a view or selects a created view for each menu item so that you can perform a screen schedule and have basic control over the monitors from the server.
  • Page 63 Tools Menu Synchronize Synchronizes the library files of the main server with the files of the content server. Option Changes the server settings. For more information, refer to the Options section. Library...
  • Page 64 Tree View List View Output View Tree View All the folders under My Computer on the Windows Desktop, library, screen, and content server are displayed in a tree view. If you select a folder, its subfolders and a list of files in it are displayed in the list view in the right pane. Exploring Normal Files Exploring Libraries Exploring Screen Files...
  • Page 65 Displays the screen management folders created with the Screen menu in a tree view. Function: Displays the subfolders and screen files below the selected folder in the list window on the right by selecting a folder. Hot Key F2 key: Renames the selected folder. Delete key: Deletes the selected folder, its sub folder(s) and all the files in the selected folder and subfolders.
  • Page 66 Double-click to move to the upper folder. Double-click to move to the lower folder. Double-click a file to run the file. Drag & Drop If you drag and drop a file from the list view into a library, it is registered to that library. However, the drag &...
  • Page 67 If you drag and drop library files into a library folder in the tree view or list view, they are moved to that folder if the content types of both the library files and the library folder are the same. However, the drag &...
  • Page 68 - Comments : Comments entered by the user for the selected library file. You can edit them. New Folder: This menu item is only activated when neither a folder nor a file is selected. If you select this menu item, a new folder is created. However, it is deactivated when a library or office folder is selected in the tree view.
  • Page 69 If you drag and drop screen files to a screen folder in the tree view or the list view, they are moved to that folder. However, the drag & drop function is not supported for folders. Context Menu Open: If you click Open for a folder, you are moved to that folder. However, this menu item is deactivated when a screen file is selected.
  • Page 70 - Name: The name of the selected screen - Location : The location where the selected screen is registered - Size : The size of the selected screen - Resolution : The resolution of the selected screen - Duration : The playing time of the selected screen - Date Modified : The date when the selected screen was last modified - Target : The real location of the selected screen.
  • Page 71 Displays the subfolders and content servers below the selected folder. Function: Double-Click Double-click to move to the upper folder. Double-click to move to the lower folder. Drag & Drop If you drag and drop content servers to a content server folder in the tree view or the list view, they are moved to that folder.
  • Page 72 1) Mac Address: The MAC address of the selected content server. You can edit this. 2) Server Name: The server name of the selected content server. You can edit this. 3) IP Address: The IP address of the selected content server. You cannot edit this. * The IP address is displayed if the content server is connected at least once.
  • Page 73 Hot Key Ctrl + C: Copies the selected message to the clipboard so that you can paste it to another location.
  • Page 74 What is MagicInfo Pro? Using MagicInfo Pro Remote Management Message Screen File Menu Library / Screen / Schedule / Remote Management / Message Creates a view or selects a created view for each menu item so that you can perform a screen schedule and performs basic control for the monitors from the server.
  • Page 75 accounts that can be created: Administrator and User Accounts Administrator: Has privileges for all server functions. User: Has privileges for all server functions except for changing server options and user account features. Exit Exits the program. If there are any unsaved changes, a new window is displayed so that you can save them.
  • Page 76 Screen Tree View Edit View List View Tree View A tree is created in accordance with the order of the areas created in the Edit View. You can check the area currently selected in the Edit View using the Tree View. If you select a property of an area, the detailed property information is displayed in the List View.
  • Page 77 New: Initializes the screen view you are currently working with. If there are any unsaved changes, a new window is displayed so that you can save them. Open: Opens a screen file. If there are any unsaved changes, a new window is displayed so that you can save them.
  • Page 78 Name: Changes the background name. You cannot use a name already used for another area name. Resolution: Changes the resolution for the background. You can add a new resolution and set the default resolution using the Options menu. Start Time, Stop Time, Duration: Sets the playing time of the background in minutes. The playing time of the background changes to that of the screen.
  • Page 79 Tile: The photo file is tiled continuously across the entire background. Time Interval: Sets the slide show time between photo files when the background type is set to Photo File. Office File: Selects the office files when the background type is set to Office File. You can create the background using a Power Point, Excel, Word, or PDF file.
  • Page 80 Sound: Turns the background sound on or off. Music File: Selects a music file for the background. Volume: Controls the volume of the background music. Repeat: A music file can be played repeatedly. When set to Repeat, the music file is played repeatedly while the background is created.
  • Page 81 Photo This function is for configuring screens using photo files and consists of the Area, Screen, Background, Effect functions. The Area function allows you to set the position where the photo is displayed and when and for how long it is displayed. The Screen function allows you to select photo files and how to display them.
  • Page 82 Screen Photo File: Selects a photo file to play in the Photo area. Aspect Ratio: Selects the aspect ratio for the photo files to be played in the Photo area. Full: The photo file is enlarged or reduced to fit the entire background. Original: The photo file is displayed at the original size.
  • Page 83 Picture File: Selects the photo file when the background type for the Photo area is set to Picture File. Picture Aspect Ratio: Selects the aspect ratio for the photo file when the background type of the Photo area is set to Picture File. Full: The photo file is enlarged or reduced to fit the entire background.
  • Page 84 Effect: Selects the type of effect to be applied when the Photo area is created. None: No effect is used. Slide: The Photo area is created while it is moving. Block: The Photo area is created with blocks. Fade In: The Photo Area fades in when it is created. Effect Speed: Adjusts the speed of an effect being created.
  • Page 85 Name: Changes the area name. You cannot use a name already used for another area name. Lock Position: Locks the position of the area. Left, Top, Width, Height: Changes the position and size of the area. The area positions must be within the background and the area size cannot be larger than the background size.
  • Page 86 Movie Repeat: A movie file can be played repeatedly. When set to Repeat, the movie file is played repeatedly while the background is created. Background Type: Sets the background type (Color, Picture File) for the Movie area. Color: Selects the color when the background type for the Movie area is set to Color. Transparency: Selects the degree of transparency when the background type for the Movie area is set to Color.
  • Page 87 Changes the detailed properties and the transfer mode for the selected file of each type. Transfer Mode: Changes the mode in which the selected file is transferred to the monitor. Download: Downloads the file to the monitor and plays it. Stream: Streams the file to the monitor.
  • Page 88 This function is for configuring screens using Macromedia flash files and consists of Area, Screen, Background, Effect functions. The Area function allows you to set the position where the movie is played and when and for how long it is played. The Screen function allows you to set the flash file and how to play it.
  • Page 89 Screen Flash File: Selects the flash file to be played in the Flash area. Aspect Ratio: Selects the aspect ratio for the flash file to be played in the Flash area. Full: The flash file is enlarged or reduced to fit the entire background. Original: The flash file is displayed at the original size.
  • Page 90 Picture Aspect Ratio: Selects the aspect ratio for the photo file to be played in the Flash area when the background type of the Flash area is set to Picture File. Full: The photo file is enlarged or reduced to fit the entire background. Original: The photo file is displayed at the original size.
  • Page 91 Effect: Selects the type of effect to be applied when the Flash area is created. None: No effect is used. Slide: The Flash area is created while it is moving. Block: The Flash area is created with blocks. Fade In: The Flash area fades in when it is created. Effect Speed: Adjusts the speed of an effect being created.
  • Page 92 Name: Changes the area name. You cannot use a name already used for another area name. Lock Position: Locks the position of the area. Left, Top, Width, Height: Changes the position and size of the area. The area positions must be within the background and the area size cannot be larger than the background size.
  • Page 93 Background Type: Sets the background type (Color, Picture File) for the Web area. Color: Selects the color when the background type for the Web area is set to Color. Transparency: Selects the degree of transparency when the background type for the Web area is set to Color.
  • Page 94 Changes the detailed properties and the transfer mode for the selected file of each type. Transfer Mode: Changes the mode in which the selected file is transferred to the monitor. Download: Downloads the file to the monitor and plays it. Stream: Streams the file to the monitor.
  • Page 95 This function is for configuring screens by connecting text and consists of the Area, Screen, Background, Effect functions. The Area function allows you to set the position of the text and when and for how long it is displayed. The Screen function allows you to select the text and how to display it. The Background function allows you to set the background image and music when the text is displayed.
  • Page 96 Text: Sets the text to be displayed in the Text area. Direction: Sets the direction of the text flow in the Text area. None Right to Left Left to Right Top to Bottom Bottom to Top Text Speed: Sets the speed of the text flow in the Text area. Step: Sets the interval of the text flow in the Text area.
  • Page 97 Color: Selects the color to use when the background type for the Text area is set to Color. Transparency: Selects the degree of transparency to be used when the background type for the text area is set to Color. If the Transparency is set to a value under 100, the area which is placed beneath the present area is shown transparently.
  • Page 98 Effect: Selects the type of effect to be applied when the Text area is created. None: No effect is used. Slide: The Text area is created while it is moving. Block: The Text area is created with blocks. Fade In: The Text area fades in when it is created. Effect Speed: Adjusts the speed of an effect being created.
  • Page 99 Name: Changes the area name. You cannot use a name already used for another area name. Lock Position: Locks the position of the area. Left, Top, Width, Height: Changes the position and size of the area. The area positions must be within the background and the area size cannot be larger than the background size.
  • Page 100 Edit View This view is used for screen design and allows you to create, move and change the size of an area using your mouse. You can preview the current state by selecting Preview Area from the context menu or double-clicking on an area. Context Menu Area: Selects the type of area you wish to create.
  • Page 101 What is MagicInfo Pro? Using MagicInfo Pro Remote Management Message Schedule File Menu Library / Screen / Schedule / Remote Management / Message Creates a view or selects a created view for each menu item so that you can perform a screen schedule and performs basic control for the monitors from the server.
  • Page 102 Tool Menu Undo / Redo Cancels the previously performed command or performs the canceled command again. You can change the maximum number of commands that you can undo using the Option menu. Adds the screen you wish to schedule after selecting a monitor and time by clicking in the EPG window.
  • Page 103 Schedule Tree View EPG View List View Publish View Tree View Displays the connection state of the monitors currently connected to the server depending on the monitor icon. You can also efficiently manage the monitors by creating network groups. You can move a networked monitor by dragging and dropping it into a group.
  • Page 104 Network: A monitor which is connected to the server over a network. New Group: Creates a new group that can include some networked monitors. You can drag and drop a networked monitor to a group. Copy/Paste: Copies all the schedules configured on the selected monitor to the clipboard and pastes them to another monitor.
  • Page 105 This is a virtual monitor used to create schedules for a monitor used without being connected to the network. Local publishing can be performed for a local monitor to create schedules for it. New Monitor: Creates a new virtual local monitor. Copy / Paste: Copies the schedules set on the selected monitor and pastes them to another monitor.
  • Page 106 Add: Adds the screen you wish to schedule after selecting a monitor and time by clicking in the EPG window. Delete: Deletes the screen currently selected in the EPG window. Copy / Paste: Copies the currently selected screen and pastes it after selecting a monitor and time by clicking in the EPG window.
  • Page 107 Name: Changes the name of the selected screen. Only the screen name changes and the time information is retained. Start Time / Stop Time / Duration: Sets the time information for the selected screen in minutes. Periodic: Sets how frequently the selected screen recurs. (None / Daily / Weekly / Monthly) End on: Sets an end date for the selected schedule to recur.
  • Page 108 What is MagicInfo Pro? Using MagicInfo Pro Message Remote Management Remote Management File Menu Library / Screen / Schedule / Remote Management / Message Creates a view or selects a created view for each menu item so that you can perform a screen schedule and have basic control over the monitors from the server.
  • Page 109: Remote Management

    Tools Menu Refresh Refreshes the value of each client for the currently selected remote control item. Option Changes the server settings. For more information, refer to the Options section. Remote Management Tree View List View Combo View...
  • Page 110 Tree View Displays various control items for the client in a tree view. If you select an item, the current state of the selected item is displayed and you can control it in the list view. Displays the items for which remote management is required from among the OSD menus of each client monitor in a tree view.
  • Page 111 1) Hour: Enter the hour. 2) Minute: Enter the minutes. 3) AM/PM: Enter AM or PM. -On Timer 1) Hour: Enter the hour. 2) Minute: Enter the minutes. 3) AM/PM: Enter AM or PM. 4) Status: Select whether to use the turn-on time. 5) Source: Select the external input 6) Volume: Select the volume -Off Timer...
  • Page 112 System Displays the items required to manage the client in the tree view separately from MDC. If you select an item, the current state of the selected item is displayed and you can control it in the list view. Detailed Items System: Displays the product information for the client in a list view.
  • Page 113 mode. The Color Temperature item is only applicable if the Color Tone item is turned off. The Auto Wide option for the Size item is only available in TV mode. (Only applicable for monitors that support TV.) Picture PC: Displays the current state of MagicBright, contrast, brightness, color tone, red, green, blue, color temp, and size.
  • Page 114 3) Type: Enter the type of screensaver. Video Wall 1) Video Wall: Select whether to activate the video wall. 2) Horizontal: Set how many parts the screen is divided into horizontally. 3) Vertical: Set how many parts the screen is divided into vertically. : Select the area that the monitor will display.
  • Page 115 System Displays the items required to manage the system properties of the client in a tree view. You have to set the settings for each item by double-clicking the client or using the Edit item from the context menu, instead of selecting each item and setting a value as in MDC. Detailed Items System: Displays the information for the model name, serial number, screen size, firmware version, MagicInfo Pro version, and OS image version.
  • Page 116 1) Current Status: Displays the current EWF status of the selected client. 2) EWF command: Changes the EWF status of the selected client. 3) Screen Rotation: Selects the screen direction of the selected client. 4) Screen Resolution: Displays the resolution of the selected client. 5) System message: Selects whether to display a system message for the selected client.
  • Page 117 Context Menu Update: This item is only enabled if a monitor name is selected. This item compares the client version to the update version on the server and updates the client if required. Edit: Displays a window so that you can change the monitor settings. For the System, General, and Performance items, the settings are read-only so they are disabled.
  • Page 118 What is MagicInfo Pro? Using MagicInfo Pro Remote Management Message Message File Menu Library / Screen / Schedule / Remote Management / Message Creates a view or selects a created view for each menu item so that you can run a screen schedule and perform basic control for the monitors from the server.
  • Page 119 user account features. Exit Exits the program. If there are any unsaved changes, a new window is displayed so that you can save them. Tool Menu Undo / Redo Cancels the previously performed command or performs the canceled command again. You can change the maximum number of commands that you can undo using the Option menu.
  • Page 120 Tree View List View Tree View You can select the monitors to which the message is sent by checking the checkbox next to each monitor and group. List View Changes the detailed functions for the message to be sent to the monitors by double-clicking it or by clicking the created button.
  • Page 121: Table Of Contents

    What is MagicInfo Pro? Using MagicInfo Pro Remote Management Message Option Option General Network Connection: Selects the connection method between the server and the monitor. The server and monitor can be connected to each other only if the same connection method is used. Automatic connection: The monitor automatically connects a server on the same network.
  • Page 122 Direct connection: The monitor directly connects to the server with the specified IP address. If the server and monitor are on a different private network, they cannot connect to each other. However, if the server has a public IP address, a monitor with a private IP address can be connected to it using the direct connection method.
  • Page 123 Use the available disk space of each monitor: Sets the size to the maximum free disk space of the monitor. Use the equal disk space of each monitor: Sets the size to the value entered in the edit box. Do not check disk space when schedule is published: Publishing continues even though the total size of the schedules to be published is larger than that of the free disk space of the monitor.
  • Page 124 What is MagicInfo Pro? Using MagicInfo Pro Remote Management Message Contents Server A program run on the additional PC where the content server is operating. Version: The version of the content Server. MAC ID: The MAC address of the network device on the PC where the content server is installed.
  • Page 125 Displays or changes the drive settings. Password Manages the password. Setup Rotation Rotates the screen with the selected option. Program Runs or exits the program. Exit Exits mnMain. If you exit mnMain, MagicInfo Pro and the Schedule program are also exited together.
  • Page 126 Old password Enter the existing password. New password Enter the new password. Change Change the password. Use password lock Verifies your password before you enter the Setup screen. Setup Connection Tab Schedule server Server Connection Settings The client automatically connects to the server. When a connection is disconnected, the client connects to another server automatically.
  • Page 127 The ID of the server to connect to Client ID 1 Schedule server Automatic connection using server name : If the schedule server and client are on the same sub network, the client connects to the servers using their name. Reconnecting another server when disconnected : If a connection is disconnected, the client connects to another server on the same sub network automatically.
  • Page 128 Select the program performed when the client starts. Automatic updates Select how to perform automatic updates. 1 Startup Sets the program to be performed when the client starts. You can select one of two programs, or select neither of them. Player: Runs a media player program that can be run using the remote control and can receive and play the content that exists on the server.
  • Page 129 Background: Sets the background for the entire screen. File: Sets the logo screen to be displayed on the background. (A flash, photo, or movie file can be set.) 2 Schedule folder Sets the directory which the content to be scheduled is downloaded to and managed in and manages the size of the disk.
  • Page 130: Client / Contents

    What is MagicInfo Pro? Using MagicInfo Pro Remote Management Message Troubleshooting When a monitor is not connected to the server Check whether the network environment for the server and monitor is normal.. (Check the network cable connections and IP address settings, etc) Check whether a correct network card has been selected when there is more than one network card in the PC where the server is operating.
  • Page 131 When the monitor update function does not work Check the monitor version. If it is the latest version, no updating is performed. When a movie file is not registered to the library Check whether the proper codec is installed for the movie file the server wants to register to the monitor.
  • Page 132 MagicInfo Pro 소개 Screen Design Remote Management Option 프로그램 제거 MagicInfo Pro는 Windows 프로그램 추가/제거 옵션을 사용하거나 프로그램 설치시 추가되는 메뉴를 통해 제거할 수 있습니다. MagicInfo Pro를 제거하려면 다음 단계를 수행하십시오. 시스템 트레이에서 [시작] 메뉴로 이동하고 [설정]을 선택한 다음 메뉴에서 [제어판]을 선택합니다. 2.
  • Page 133: Source List

    Adjusting the LCD Display Input Available Modes • PC / DVI • • HDMI • MagicInfo • Source List MENU → ENTER → [Input] → ENTER → [Source List] → , → ENTER Use to select PC, DVI or other external input sources connected to the LCD Display. Use to select the screen of your choice.
  • Page 134 → , → ENTER Name the input device connected to the input jacks to make your input source selection easier. HDMI Picture [PC / DVI / MagicInfo Mode] Available Modes • PC / DVI • • HDMI • MagicInfo • MagicBright MENU →...
  • Page 135 Entertain High brightness For watching motion pictures such as a DVD or VCD. Internet Medium brightness For working with a mixture of images such as texts and graphics. Text Normal brightness For documents or works involving heavy text. Custom Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste.
  • Page 136: Color Tone

    → , → ENTER Adjusts the Sharpness. Color Tone MENU → → ENTER → [Picture] → → →ENTER → [Color Tone] → , → ENTER The color tones can be changed. (Not available in Dynamic Contrast mode of On.) Cool Normal Warm Custom...
  • Page 137: Color Temp

    → , → ENTER Green MENU → → ENTER → [Picture] → → → → ENTER → [Color Control] → ENTER → → [Green] → , → ENTER Blue MENU → → ENTER → [Picture] → → → [Blue] → , → ENTER Color Temp MENU →...
  • Page 138: Auto Adjustment

    Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. Fine MENU → → ENTER → [Picture] → → → [Fine] → , → ENTER Removes noise such as horizontal stripes.
  • Page 139: Signal Control

    (Available in PC mode only) Signal Balance MENU → → ENTER → [Picture] → → ENTER → [Signal Balance] → , → ENTER Selects either On or Off with the signal control. Signal Control MENU → → ENTER → [Picture] → →...
  • Page 140 → , → ENTER G-Offset MENU → → ENTER → [Picture] → ance] → → ENTER → [Signal Control] → ENTER→ → → → → [G-Offset] → , → ENTER B-Offset MENU → → ENTER → [Picture] → ance] → → ENTER → [Signal Control] → ENTER→ → → → → → [B-Offset] →...
  • Page 141 Picture [ AV / HDMI / TV Mode] Available Modes • PC / DVI • • HDMI • MagicInfo • Mode MENU → → ENTER → [Picture] → ENTER → [Mode] → , → ENTER The LCD Display has four automatic picture settings ("Dynamic", "Standard", "Movie" and "Cus- tom") that are preset at the factory.
  • Page 142 Contrast MENU → → ENTER → [Picture] → → ENTER → [Custom] → ENTER→ [Contrast] → , → ENTER Adjusts the Contrast. Brightness MENU → → ENTER → [Picture] → → ENTER → [Custom] → ENTER → → [Brightness] → , → ENTER Adjusts the Brightness.
  • Page 143 → , → ENTER The color tones can be changed. The individual Color components are also user adjustable. (Not available in Dynamic Contrast mode of On.) Cool2 Cool1 Normal Warm1 Warm2 Note If you set the Color Tone to Cool2, Cool1, Normal, Warm1, or Warm2, the Color Temp function is disabled.
  • Page 144: Film Mode

    → , → ENTER The Size can be switched. 16:9 Zoom 1 Zoom 2 Just Scan (Not available in Dynamic Contrast mode of On.) Note The Zoom1, Zoom2 are not available HDMI. The Just Scan are available in HDMI. Digital NR (Digital Noise Reduction) MENU →...
  • Page 145: Brightness Sensor

    The Film Mode feature offers you a theater-quality viewing experience. (Not available in HDMI Mode) Brightness Sensor MENU → → ENTER → [Picture] → → → → → → → → ENTER → [Brightness Sensor ] → , → ENTER Brightness Sensor is to automatically detect distribution of inputted visual signal and adjust to create optimum brightness.
  • Page 146 • • HDMI • MagicInfo • Mode MENU → → → ENTER → [Sound] → ENTER → [Mode] → , → ENTER The LCD Display has a built-in high fidelity stereo amplifier. Standard Selects Standard for the standard factory settings. Music Selects Music when watching music videos or concerts.
  • Page 147: Auto Volume

    → , → ENTER Emphasizes low frequency audio. Treble MENU → → → ENTER → [Sound] → → ENTER → [Custom ]→ →ENTER→ [Treble] → , → ENTER Emphasizes high frequency audio. Balance MENU → → → ENTER → [Sound] → → ENTER → [Custom ]→ → →ENTER→ [Bal- ance] →...
  • Page 148 → , → ENTER SRS TS XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers. TruSurround delivers a compelling, virtual surround sound experience through any two-speaker playback system, including internal television speakers. It is fully compatible with all multichannel formats.
  • Page 149: Clock Set

    Note The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. Time Selects from one of 4 time settings, Clock Set, Sleep Timer, On Timer, and Off Timer. MENU → → → → ENTER → [Setup] → → ENTER → [Time ] Clock Set MENU →...
  • Page 150: Off Timer

    On Timer MENU → → → → ENTER → [Setup] → → ENTER → [Time ] → → → ENTER→ [On Timer] → , / , → ENTER Turns the LCD Display on automatically at a preset time. Controls the mode and the volume level at the time the LCD Display turns on automatically.
  • Page 151: Energy Saving

    Opaque Safety Lock PIN MENU → → → → ENTER → [Setup] → → → → ENTER → [Safety Lock PIN ] → [0 9] → [0 9] → [0 9] → [0 9] The password can be changed. Energy Saving MENU →...
  • Page 152 → , → ENTER When a DVD or set-top box is connected to your TV via HDMI, it may cause a degradation in the screen quality, such as an increase in the black level, a low contrast, or discoloration, etc., depending on the external device connected.
  • Page 153 Format MENU → → → → ENTER → [Setup] → → → → Wall ]→ → ENTER → [Format] → , → ENTER The Format can be selected to see a divided screen. Full Provides a full screen without any margins. Natural Displays a natural image with the original aspect ratio intact.
  • Page 154: Safety Screen

    → , → ENTER Sets how many parts the screen should be divided vertically. Five adjustment levels: 1, 2, 3, 4, and 5. Screen Divider MENU → → → → ENTER → [Setup] → → → → Wall ]→ → → → → ENTER → [Screen Divider] The screen can be divided into several images.
  • Page 155 Interval MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen]→ → ENTER → [Interval] → , → ENTER Determines the time interval to run the Safety Screen operation. The time is calculated on the basis of the power on time. By default, the time is set to 10 mins and 10 hours respectively.
  • Page 156 → , → ENTER You can change the Safety Screen Type. Scroll Pixel Shift Eraser Horizontal Dot MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen]→ → → → ENTER → [Horizontal Dot] →...
  • Page 157: Resolution Select

    Five adjustment levels: 0, 1, 2, 3, and 4. Resolution Select MENU → → → → ENTER → [Setup] → → → → [Resolution Select ] → , → ENTER When the picture is not displayed properly on the screen when setting the graphics card resolution of the computer to 1024 x 768 @ 60Hz, 1280 x 768 @ 60Hz, 1360 x 768@ 60Hz or 1366 x768 @ 60Hz, by using this function(Resolution Select), you can have the picture displayed on the screen in the specified resolution.
  • Page 158 Caution: Set the Power On time to be loger to avoid overvoltage. Side Gray MENU → → → → ENTER → [Setup] → → → → → → → → → → → ENTER → [Side Gray] → , → ENTER Select the brightness of the grey for the screen background.
  • Page 159: Multi Control

    → , → ENTER Lamp Control MENU → → → → ENTER → [Setup] → → → → → → → → → → → → → ENTER → [Lamp Control ] → , → ENTER Adjusts the inverter lamp in order to reduce energy consumption. Note This function does not operate when Dynamic Contrast is set to On in PC, DVI, AV, HDMI, TV modes.
  • Page 160 MagicInfo Available Modes • PC / DVI • • HDMI • MagicInfo • Note • The operating system for this set only supports English so the other languages might be corrupted on the screen. • For MagicInfo, a remote control is available for MagicInfo. However, it is recommended using a separate USB keyboard.
  • Page 161 • When the contents of Setup have been changed when EWF is in the Enable state, to save the changes in the disk, you must Commit them. • By selecting Disable, Enable or Commit, the system is restarted. Photo The JPEG, BMP file format are supported. Auto Automatically fits the image to the window.
  • Page 162: Slide Show

    Slide Show Displays the properties of the original file as they are. Interval Controls the time intervals between image files for a slide show. (5 Sec, 10 Sec, 20 Sec, 30 Sec, 60 Sec) Adjusting the LCD Display...
  • Page 163 Rotation Displays an image file by turning it clockwise by 90 degrees. Zoom Displays a reduced picture. Adjusting the LCD Display...
  • Page 164 Close Closes the image control Menu. Music The MP3 file format is supported. Movie The MPEG1, WMV file format are supported. Adjusting the LCD Display...
  • Page 165 Play Plays a movie file. Full Size Plays a movie file in full screen. Adjusting the LCD Display...
  • Page 166 OFFICE / HTML PPT(Power Point), DOC(MS Word), XLS(MS Excel), PDF, HTML, HTM files are displayed. Note • Install the proper viewer(freeware) program to see the MS Office(Word, Excel, Power Point) or PDF doucuments. Internet Connects to the Internet Setup Sets various functions in MagicInfo mode. A password must be entered to access Setup mode. Adjusting the LCD Display...
  • Page 167: Schedule View

    Schedule View Displays a schedule. TCP/IP Changes the TCP/IP settings. Adjusting the LCD Display...
  • Page 168 Connection Modifies the network settings. Password The password can be changed. • The password should be between 6 and 12 characters in numeric format. (You should enter a password between 6 and 12 characters in numeric format) • If you enter the wrong password three times, the setup configuration is reset and a warning message appears from the server.
  • Page 169: Play Option

    • If you forget the password, enter Info, 8, 2 and 4 on the remote control to initialize the password. This will reset the previous settings of Setup mode. File Local : You can delete or copy files on both local and removable disks. Play Option You can set the repeat play and screen settings.
  • Page 170 Adjusting the LCD Display • File Repeat - Select Repeat File to play a movie or tune in the list repeatedly. • List Repeat - Select Repeat List to play movies or tunes in the list in sequence repeatedly. Rotation - Sets the picture orientation. •...
  • Page 171: Troubleshooting

    Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check Turn off both your computer and the LCD Display. Unplug the video cable from the back of the computer. Turn on the LCD Display.
  • Page 172: Check List

    • Do not use benzene, thinner or other flammable substan- ces, or a wet cloth. • We recommend that a SAMSUNG cleansing agent is used to prevent damage to the screen. • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen sur- face.)
  • Page 173: Problems Related To The Screen

    Check if the signal cable between the computer and the LCD Display is securely connected. (Refer to Connecting a Computer) Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed. The screen is blank and the power indicator is off. Ensure that the power cord is firmly connected and the LCD Display is on.
  • Page 174: Problems Related To Audio

    Adjust color using Custom under OSD Color Adjustment menu. The color image is distorted by dark shadows. Adjust color using Custom under OSD Color Adjustment menu. The color white is poor. Adjust color using Custom under OSD Color Adjustment menu. The Power Indicator blinks.
  • Page 175 Check if the power is on. Check if the power cord is securely connected. Check if a special fluorescent or neon lamp is on in the vicinity. Problems related to MagicInfo Note Making a Bootable USB Flash Disk. Making a Bootable USB Flash Disk 1) You can turn a common 512-MB or bigger USB storage media into a bootable disk using a USB bootable disk creation tool.
  • Page 176 Set the resolution at the Control Panel → Display → Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Man- ual). How can I clean the outer case/LCD Panel? Disconnect the power cord and then clean the LCD Display with a soft cloth, using either a cleaning solution or plain water.
  • Page 177: Specifications

    Specifications General General Model Name LCD Panel Size Display area Pixel Pitch Synchronization Horizontal Vertical Display Color 16.7 M Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB 0.7 Vp-p ±5 % Separate H/V sync, Composite, SOG TTL level (V high ≥...
  • Page 178 Dimensions (W x H x D) / Weight SyncMaster 320MXn VESA Mounting Interface 200 x 200 mm Environmental considerations Operating Storage Plug and Play Capability This LCD Display can be installed on any Plug & Play compatible system. The interaction of the LCD Display and the computer systems will provide the best operating conditions and LCD Display settings.
  • Page 179 Item Music Movie File Internet Browser Language MagicInfo Pro - Server Requirement Note This is activated when a network box is installed in the MXn or MX model. Minimum Recommended PowerSaver This LCD Display has a built-in power management system called PowerSaver. This system saves energy by switching your LCD Display to low-power mode when it has not been used for a certain amount of time.
  • Page 180: Preset Timing Modes

    Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows. Display Mode IBM, 640 x 350 IBM, 640 x 480...
  • Page 181: For Better Display

    Information For Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFT-LCD. •...
  • Page 182 Power Off, Screen Saver, or Power Save Mode • Turn the power off for 4 hours after 20 hours in use • Turn the power off for 2 hours after 12 hours in use • Set the Monitor to power off with the PC Display Properties Power Scheme. •...
  • Page 183 • Avoid using a combination of characters and background color with large difference in luminance. Avoid using Grey colors, which can cause Image retention easily. Avoid: Colors with big difference in luminance (Black & White, Grey) Change the characters color periodically •...
  • Page 184 Note ( Please check CD's User Guide at "OSD Function", some model's will not available ) Apply the Screen Pixel function on Product • Apply the Screen Pixel function - Symptom: Dot with Black Color move up and down. - Select method •...
  • Page 185 - Select method • Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Eraser • Time Interval : 1 ~ 10 hours ( Recommend : 1 ) • Time Period : 10 ~ 50 second ( Recommend : 50 ) Note ( Please check CD's User Guide at "OSD Function", some model's will not available ) Information...
  • Page 186: Contact Samsung Worldwide

    Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. U.S.A CANADA MEXICO ARGENTINE BRAZIL CHILE COLOMBIA COSTA RICA ECUADOR EL SALVADOR GUATEMALA HONDURAS JAMAICA NICARAGUA PANAMA PUERTO RICO REP.
  • Page 187 GERMANY 01805 - SAMSUNG (726-7864) (€ 0,14/Min) HUNGARY 06-80-SAMSUNG (726-7864) ITALIA 800-SAMSUNG (726-7864) LUXEMBURG 0035 (0)2 261 03 710 NETHERLANDS 0900 SAMSUNG (726-7864 € 0,10/Min) NORWAY 815-56 480 POLAND 0 801 801 881 022-607-93-33 PORTUGAL 80820-SAMSUNG (726-7864) http://www.samsung.com/pt SLOVAKIA 0800-SAMSUNG (726-7864)
  • Page 188 Vertical Frequency Horizontal Frequency Interlace Non-Interlace Methods Plug & Play Resolution SRS TS XT Appendix Asia Pacific 0800-329-999 http://www.samsung.com/tw 1 800 588 889 http://www.samsung.com Middle East & Africa 0860-SAMSUNG(726-7864) http://www.samsung.com 444 77 11 http://www.samsung.com 800-SAMSUNG(726-7864) http://www.samsung.com 8000-4726 The image on a monitor is composed of red, green and blue dots.
  • Page 189: Correct Disposal

    Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or con- sequential damages in connection with the furnishing, performance, or use of this material.

This manual is also suitable for:

Syncmaster 320mxn

Comments to this Manuals

Symbols: 0
Latest comments: