Related Manuals for Vaillant uniSTOR VIH GB /3 BES Series
Summary of Contents for Vaillant uniSTOR VIH GB /3 BES Series
- Page 1 Installation and maintenance instructions uniSTOR VIH GB .../3 BES GB, IE Publisher/manufacturer Vaillant GmbH Berghauser Str. 40 D-42859 Remscheid Tel. +492191 18 0 Fax +492191 18 2810 info@vaillant.de www.vaillant.de...
-
Page 2: Table Of Contents
Contents Contents Commissioning Checklist......... 19 Index ................... 22 Safety ..............3 Action-related warnings ......... 3 Risk caused by inadequate qualifications....3 Intended use ............3 General safety information ........3 Regulations (directives, laws, standards) ....4 Notes on the documentation ......5 Observing other applicable documents .... -
Page 3: Safety 1
Safety 1 Safety for the product and any other system com- ponents Action-related warnings – installing and setting up the product in ac- Classification of action-related warnings cordance with the product and system ap- proval The action-related warnings are classified in –... -
Page 4: Regulations (Directives, Laws, Standards)
1 Safety 1.4.4 Risk of material damage caused by using an unsuitable tool ▶ Use the correct tool. 1.4.5 Risk of material damage caused by frost ▶ Do not install the product in rooms prone to frost. 1.4.6 Risk of injury due to the heavy weight of the product ▶... -
Page 5: Notes On The Documentation 2
VIH GB 300/3 BES 0010019214 Benchmark Vaillant is a licensed member of the Benchmark Scheme. Benchmark places responsibilities on both manufacturers and installers. The purpose is to ensure that customers are provided with the correct equipment for their needs, that it is installed, commissioned and serviced in accordance with the manufacturer’s instructions by a competent person approved... -
Page 6: Hot Water Association
Hot Water Association Install the product in such a way that the thermostat and immersion heater can be accessed easily. Vaillant is a full member of the Hot Water Association and – Leave sufficient space around the product for installing, promotes the scheme in association with its cylinder range. -
Page 7: Unpacking The Product
Set-up 4 Unpacking the product Product dimensions,slimline Remove the product from its box. Validity: VIH GB 120/3 BES Remove the protective film from all of the product's OR VIH GB 150/3 BES components. Caution. Risk of material damage caused by un- packing incorrectly. -
Page 8: Product Dimensions, Standard Diameter
5 Installation Installation Product dimensions, standard diameter Validity: VIH GB 180/3 BES Setting up the unit horizontally OR VIH GB 200/3 BES ▶ Align the product vertically by adjusting the adjustable OR VIH GB 250/3 BES feet. OR VIH GB 300/3 BES Hydraulic connection Caution. - Page 9 Installation 5 5.2.4 Installing a discharge pipe ≥ 300 mm Temperature and pres- Tundish sure expansion relief valve The drain connections of the temperature and pressure re- lief valve and the expansion relief valve must be connected Heat generator heating Domestic hot water return outlet...
- Page 10 5 Installation age point. According to the table, the maximum permiss- Validity: Except for VIH GB 120/3 BES ible resistance for a straight length of a 22-mm-thick cop- OR Except for VIH GB 150/3 BES per discharge pipe (D2) of a thermal expansion relief valve G1/2 is 9.0 m.
-
Page 11: Electrical Installation
Installation 5 5.2.6 Installing a secondary return Validity: VIH GB 250/3 BES OR VIH GB 300/3 BES 60 50 60 50 Immersion heater Primary circuit thermo- stat Immersion heater ther- Retainer for the temper- mostat ature sensor 5.3.1 Optional combination of thermostats Use the wiring diagram in the system instructions for the T-piece for the second- Secondary return pipe... - Page 12 5 Installation 5.3.3 Cable route 5.3.4 Connecting the immersion heater to the power supply Validity: Except for VIH GB 120/3 BES OR Except for VIH GB 150/3 BES 60 50 60 50 ▶ Use the grommets that are included in the scope of delivery for the cylinder in the electronics box.
-
Page 13: Start-Up
Start-up 6 5.3.6 Connecting the control Condition: Y plan Condition: eBUS The thermal cut-out for the primary circuit is not used when connecting an eBUS unit. Condition: 230 V control If you use a 230 V control from a third-party manufacturer, connect the thermal cut-out (2) and (3) for the primary circuit with the 2-way motorised valve to isolate the heat source in the event of a fault in the 2-way motorised valve. -
Page 14: Cold Water Inlet Pressure
7 Handing the product over to the end user – Setting the thermostats: 60 ℃ Condition: Without a multi-functional module or control Start up the heat generator. ▶ Set the domestic hot water temperature as desired. Drain the heating circuit as soon as the operating temperature has been reached in order to remove any Condition: With multi-functional module or control residue from the heating installation. -
Page 15: Draining The Product
11 Customer service To ensure regular servicing, it is strongly recommended that arrangements are made for a Maintenance Agreement. Please contact Vaillant Service Solutions for further details: Telephone: 0330 100 3461 0020221302_02 uniSTOR Installation and maintenance instructions... -
Page 16: Appendix
Appendix Appendix Detecting and eliminating faults Fault Possible cause Remedy No flow rate at the valve Water supply valve closed Check and open the valve. Main filter blocked Close the water supply valve, clean the filter and the water pressure reducer. Pressure reducer not installed correctly Check whether the pressure reducer has been installed correctly. - Page 17 Appendix VIH GB VIH GB VIH GB VIH GB VIH GB VIH GB 120/3 BES 150/3 BES 180/3 BES 200/3 BES 250/3 BES 300/3 BES Temperature and pressure expansion 0.7 MPa 0.7 MPa 0.7 MPa 0.7 MPa 0.7 MPa 0.7 MPa relief valve (7.0 bar) (7.0 bar)
- Page 18 Appendix VIH GB VIH GB VIH GB VIH GB VIH GB VIH GB 120/3 BES 150/3 BES 180/3 BES 200/3 BES 250/3 BES 300/3 BES Propellant for insulating material GWP < 5 GWP < 5 GWP < 5 GWP < 5 GWP <...
-
Page 19: Contents D Commissioning Checklist
Appendix Commissioning Checklist 0020221302_02 uniSTOR Installation and maintenance instructions... - Page 20 Appendix MAINS PRESSURE HOT WATER STORAGE SYSTEM COMMISSIONING CHECKLIST This Commissioning Checklist is to be completed in full by the competent person who commissioned the storage system as a means of demonstrating compliance with the appropriate Building Regulations and then handed to the customer to keep for future reference. Failure to install and commission this equipment to the manufacturer’s instructions may invalidate the warranty but does not affect statutory rights.
- Page 21 Appendix SERVICE RECORD It is recommended that your hot water system is serviced regularly and that the appropriate Service Record is completed. Service Provider Before completing the appropriate Service Record below, please ensure you have carried out the service as described in the manufacturer’s instructions. SERVICE 01 SERVICE 02 Date:...
-
Page 22: Index
Index Index Article number ............... 5 Basic diagram................ 3 CE marking................5 Checking the pre-charge pressure of the expansion vessel .................. 15 Competent person..............3 Decommissioning ..............15 Decommissioning the product ..........15 Discharge pipe ..............9 Documents ................5 Draining the product ............ - Page 24 0020221302_02 0020221302_02 29.11.2019 Supplier Vaillant Ltd. Nottingham Road Belper Derbyshire DE56 1JT Telephone 0330 100 3461 info@vaillant.co.uk www.vaillant.co.uk © These instructions, or parts thereof, are protected by copyright and may be reproduced or distributed only with the manufacturer's written consent. Subject to technical modifications.