Table of Contents
Advertisement
Quick Links
Tread Scanner
1601 J. P . Hennessy Drive, La Vergne, TN USA 37086 615/641-7533 800/688-6359
HENNESSY INDUSTRIES LLC Manufacturer of COATS®, AMMCO® and BADA® Automotive Service Equipment and Tools.
Installation Instructions
READ these instructions before placing unit in
service. KEEP these and other materials delivered
with the unit in a binder near the machine for ease
of reference by supervisors and operators.
www.coatsgarage.com
Manual Part No.:
85611869 01
Revision: 09/20
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for HENNESSY INDUSTRIES COATS Tread Scanner
Summary of Contents for HENNESSY INDUSTRIES COATS Tread Scanner
- Page 1 1601 J. P . Hennessy Drive, La Vergne, TN USA 37086 615/641-7533 800/688-6359 www.coatsgarage.com Manual Part No.: 85611869 01 HENNESSY INDUSTRIES LLC Manufacturer of COATS®, AMMCO® and BADA® Automotive Service Equipment and Tools. Revision: 09/20...
- Page 2 IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS Do not stare directly into light source of the Avoid dangerous environments. Do not use unit. power tools or electrical equipment in damp or wet locations, or expose them to rain. Read and understand this manual before operating.
-
Page 3: Table Of Contents
Table of Contents Important Safety Instructions .........ii Owner’s Responsibility ..........iv Operator Protective Equipment ......... iv Definitions of Hazard Levels ........iv Symbols Used ............iv Installation Instructions ...........1 Information on Pre-installation Location .....1 Assembly Case for Floor Level Installation ....2 Evenness of The Measuring Unit .......2 Network Environment ..........2 Special Accessories ............2... -
Page 4: Owner's Responsibility
Owner’s Responsibility Definitions of Hazard Levels To maintain machine and user safety, the responsibility Identify the hazard levels used in this manual with the of the owner is to read and follow these instructions: following definitions and signal words: DANGER •... -
Page 5: Installation Instructions
Installation Instructions Avoiding Minimum Turning Curve Information on Pre-Installation Location General Test Conditions • Only use the Tread Scanner indoors. • Avoid direct and intense solar radiation on the glass plate. • Remove dirt and moisture beneath Tread Scanner. • The ground below the measuring unit must be suitable for installation with dowels and for tak- ing the load of the central support (concrete or asphalt floors). -
Page 6: Assembly Case For Floor Level Installation
Assembly Case for Floor Level Installation Network Environment An assembly case (not included in the scope of The customer must provide 2 static, (optionally 3) delivery, see “Special Accessories“) is required “IPv4 addresses” for Smart TV. for the floor level installation of the Tread Scanner. Designation Standard IP Addresses The assembly case must be grouted when the... -
Page 7: Measurement Bay
Measurement Bay Fig. 3: Dimensions Tread Scanner in mm 1 Master 2 Satellite 3 Direction of crossing 4 Camera housing 5 Marking for hazard zone Designation Dimension Screen/Smart TV (special acces- feet (8 meter) sory) max. distance to Tread Scanner Electrical cabinet/Switch and feet (8 meter) access point - max. -
Page 8: Set-Up Tread Scanner And Camera
Set-up Tread Scanner and Camera ➢ Both modules connected directly via network. This installation is not suited to be set up on a working pit. Fig. 5: Connecting the master and satellite to the network 1 Computer (optional: Digital Signage) 2 Electrical cabinet 3 Direction of travel 4 Adapter cable... -
Page 9: Installation Tread Scanner On Floor
Installation Tread Scanner on Floor ➢ For installation on working pit. ➢ Connect both modules individually to external switch. ➢ No Camera possible. Fig. 6: Connecting both modules individually to external switch 1 Computer (optional: Digital Signage) 2 External switch 3 Electrical cabinet 4 Direction of travel 5 Connection cable... -
Page 10: Size
Size Attach display on left or right. Fig. 7: Size Designation Dimensions Connection to quantity measurement system Max. width of measuring system 96 inches (2,445 m) Max. length of measuring system 41 inches (1,040 m) Min. inner track width inches (0,745 m) Max. -
Page 11: Foundation Layout
Foundation Layout Only for Tread Scanner floor-level. All dimensions in cm. Important: Always read and follow instructions. • 7... - Page 12 Item Description Remark Cable conduit to the electrical cabinet Laying bends of min. Ø 80; Max. 45° Grade to water drain (about 2%) Finished floor top edge OKFFB Concrete quality min. C20/25 (DIN EN 19992-1-1) Crossing direction As reference Hazard zone Hazard area to mark the tread depth measuring device acc.
-
Page 13: Floor Levelness And Central Unit
Floor Levelness and Central Unit Important: Always read and follow instructions. • 9... -
Page 14: Checklist
Checklist Component Desired IP address if deviating from 1.5 Master Satellite Camera Workshop PC Smart TV Number of DHCP clients Set-up A (installation on surface) Electrical cabinet with 2 power supply units (PartNumber) Power supply cable Neutrik to M12, 33 feet (10 m) (85611860) Data cable M12 to M12, 8.2 feet (2.5 m) (85611859) Data cable M12 to RJ45, 33 feet (10 m) (85611858) Set-up B (installation on working pit)) - Page 15 If the type C13 IEC cables included in the scope of delivery do not fit, the customer must provide 2 country-specific IEC cables. Dimensions checked, see “Size“ Floor levelness checked, see “Floor Levelness and Central Unit“ Floor load-bearing capacity checked, see “General Test Conditions“ Minimum turning curve checked, see “Avoiding Minimum Turning Curve“...
- Page 16 85611869 01 09/20 © Copyright 2020 Hennessy Industries LLC...
Need help?
Do you have a question about the COATS Tread Scanner and is the answer not in the manual?
Questions and answers