Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Vega Absolute SMART-MS0101
Summary of Contents for Vega Absolute SMART-MS0101
- Page 1 MOTION SENSOR SMART-MS0101 User Manual Infrared motion sensor Vega Smart-MS0101 is designed to detect penetration into the protected area. The sensor alternately operates in two modes: «Guard» and «Neutral». Sends an alarm signal to the LoRaWAN™ network by the triggering.
- Page 2 Smart-MS0101 / User Manual Document Information Title Motion sensor Smart-MS0101 Document type Manual – Translation from Russian Document number V05-MS0101-01 Revision and date 03 - 28.09.2018 This document applies to the following products: Product name Type number Vega Smart Vega Smart-MS0101...
-
Page 3: Table Of Contents
“LoRaWAN settings” tab ................................. 16 “Smart-MS0101” tab ................................21 5 COMMUNICATION PROTOCOL ............................22 SMART-MS0101 transmits the following types of packets ..................... 22 6 STORAGE AND TRANSPORTATION REQUIREMENTS ...................... 23 7 CONTENT OF THE PACKAGE ..............................24 8 WARRANTY....................................25 Revision №... -
Page 4: Introduction
Smart-MS0101 / User Manual INTRODUCTION This manual is designated for Vega Smart-MS0101 motion sensor (hereinafter – device, sensor) manufactured by Vega-Absolute LLC and provides information on powering and activation procedure, control commands and functions of the device. This manual is targeted at specialists familiar with installation work fundamentals for electronic and electrical equipment. -
Page 5: Description And Operation
Auto-post time interval is setting up by the «Vega LoRaWAN configurator» application and may vary from 1 to 60 minutes. Vega Smart-MS0101 can be used to protect premises, buildings and structures, as well as in Smart Home systems, built on LoRaWAN™ technology. -
Page 6: Specification
Housing dimensions 35 х 50 х 70 mm Ingress protection rating IP41 Vega Smart-MS0101 motion sensor is class A device (LoRaWAN™ classification) and has the following features: o ADR support (Adaptive Data Rate) o Sending of confirmed packets (configurable) o Extra communication in case of alarm event o Two working modes “Neutral”... -
Page 7: Operation
Smart-MS0101 / User Manual 3 OPERATION INDICATION A double color indicator is located on the front of the sensor case and it flashes red when detect motion in the protected area but no more than one at 10 seconds. Indicator on the... -
Page 8: Initial Startup
Smart-MS0101 / User Manual INITIAL STARTUP Motion sensor is powered by the CR123A 3V 1400 mAh replaceable battery. You need to insert the battery observing the polarity before start. Вставить батарейку CR123А в батарейный отсек The sensor supports two activation methods in the LoRaWAN™ network - ABP and OTAA. - Page 9 Smart-MS0101 / User Manual 2. OTAA. After pressing the start button, the device makes three attempts to connect to the network within the set frequency band. After the activation request is confirmed by LoRaWAN™ network, the device sends a signal and switches to the "Active" mode. If all attempts fail, the sensor switches to the “Storage”...
-
Page 10: Sensor Mounting Recommendations
Smart-MS0101 / User Manual SENSOR MOUNTING RECOMMENDATIONS The sensor must be installed in such a way that the probable penetration paths of the intruder cross the central axis of the detection zone. Recommended mounting height of the sensor is 2…2,5 m. -
Page 11: Connecting Via Usb
Smart-MS0101 / User Manual CONNECTING VIA USB The device Smart-MS0101 can be configured with the "Vega LoRaWAN Configurator" application (See part 4). micro-USB Before connecting the device to the computer for the first time, you must install the driver for the COM port stsw-stm32102, which can be downloaded from iotvega.com. After running the executable file VCP_V1.4.0_Setup.exe, the installer window will appear:... - Page 12 Smart-MS0101 / User Manual In this window, you need to click Next, then Install, and then the installation will begin. When the installation is completed successfully, the following screen appears: After pressing Finish the driver is ready for operation, - it is possible to connect the device via USB.
-
Page 13: Vega Lorawan Configurator
Smart-MS0101 / User Manual 4 VEGA LORAWAN CONFIGURATOR The "Vega LoRaWAN Configurator" application (hereinafter referred to as the configurator) is intended for setting up the device via USB. The configurator has two modes of operation - "Simple" and "Expert". In the "Simple"... -
Page 14: Connection To The Device
Smart-MS0101 / User Manual The language selection menu is in the upper right corner. CONNECTION TO THE DEVICE For the connection to the device, perform the following steps: 1. Connect the USB cable to the device. 2. Start the "Vega LoRaWAN Configurator" application. -
Page 15: Device Info" Tab
Smart-MS0101 / User Manual “DEVICE INFO” TAB The "Device info" tab displays information about the device, its current status, and also the data needed to register the device in the LoRaWAN™ network (Fig. 4.3). Fig. 4.3. The “Device info” tab. -
Page 16: Lorawan Settings" Tab
Smart-MS0101 / User Manual the download is complete. The current version of the device firmware can be downloaded from iotvega.com. Network info - shows whether the device is connected to the LoRaWAN™ network and its network address. Join network button - launch the LoRaWAN™ network connection procedure with the previously selected ABP or OTAA method. - Page 17 Smart-MS0101 / User Manual The sensor Smart-MS0101 supports the following frequency bands: Frequency band Channel Frequency Modulation 868.1 MultiSF 125 kHz 868.3 MultiSF 125 kHz EU-868 868.5 MultiSF 125 kHz 869.525 SF12 125 kHz 864.5 MultiSF 125 kHz 864.7 MultiSF 125 kHz RU-868 864.9...
- Page 18 Smart-MS0101 / User Manual This frequency band allows you to set up to 16 channels, as well as the frequency and speed of the second receiving window. The first three channels and the second receiving window parameters are mandatory. Without these parameters the custom frequency band will be considered empty.
- Page 19 Smart-MS0101 / User Manual Join accept delay 1 (not displayed in the "Simple" mode) – sets the time that the device will open the first receiving window to receive confirmation for the join request from the LoRaWAN™ network. The second window always opens after 1 second after the first.
- Page 20 Smart-MS0101 / User Manual TX power (not displayed in the "Simple" mode) – the device RF transmitter power is adjusted to this value when sending packets to the LoRaWAN™ network. This option can be changed by the network server. TX datarate (not displayed in the "Simple" mode) – the device transmission datarate at which it will transfer packets to the LoRaWAN™...
-
Page 21: Smart-Ms0101" Tab
Smart-MS0101 / User Manual “SMART-MS0101” TAB The “Smart-MS0101” tab contains the settings of the connected device (Fig. 4.5). Fig. 4.5. “Smart-MS0101” tab. Current state – displays the current parameters of the device - the internal temperature of the device and the battery level Guard settings –... -
Page 22: Communication Protocol
5 COMMUNICATION PROTOCOL This part describes the Smart-MS0101 data exchange protocol with LoRaWAN™ network. Smart-MS0101 uses the LoRaWAN™ port 2 for uplink and downlink messages. In fields consisting of several bytes, the little endian byte order is used. SMART-MS0101 TRANSMITS THE FOLLOWING TYPES OF PACKETS 1. -
Page 23: Storage And Transportation Requirements
Smart-MS0101 / User Manual 6 STORAGE AND TRANSPORTATION REQUIREMENTS The Smart-MS0101 sensor shall be stored in the original packaging in heated room at temperatures +5°С to +40°С and relative humidity less than 85%. The sensor shall be transported in covered freight compartments of all types at any distance at temperatures -40°C to +85°C. -
Page 24: Content Of The Package
Smart-MS0101 / User Manual 7 CONTENT OF THE PACKAGE The sensor is delivered complete with: Motion sensor Vega Smart-MS0101 – 1 pc. CR123A battery – 1 pc. Factory certificate – 1 pc. Revision № 03 - 28.09.2018... -
Page 25: Warranty
Smart-MS0101 / User Manual 8 WARRANTY The warranty period for the device is 5 years from the date of sale. The manufacturer is obligated to provide repair services or replace the failed device during the entire warranty period. The consumer undertakes to comply with the terms and conditions of transportation, storage and operation specified in this user manual. - Page 26 Smart-MS0101 / User Manual vega-absolute.ru Operation Manual © Vega-Absolute LLC 2017 Revision № 03 - 28.09.2018...
Need help?
Do you have a question about the SMART-MS0101 and is the answer not in the manual?
Questions and answers