Percent Weighing - U-Line OHAUS SCOUT H-5848 Manual

TARE CONTINUED
2. Press the TARE button. The NET indicator will be
displayed on the bottom of the display.
3. The container's weight is then stored in the scale's
0
memory and is displayed.
4. Add pieces to the container. As the pieces are
added, their net weight will be displayed.
5. Removing the container from the platform will
cause the scale to display the container's negative
number. Pressing the TARE button will readjust the
scale to zero.
WEIGHING
This mode is the factory default setting.
1. If needed, press and hold MODE until
is displayed.
2. If required, place an empty container on the
platform and press TARE.
3. Add a sample to the platform or container. The
display shows the weight of the sample.
COUNTING
This mode counts large numbers of items based on the
weight of a reference count.
1. Place an empty container on the platform and press
TARE (if needed).
2. Press and hold MODE until
CLr.PwW
(clear average piece weight, APW) will then
display. If no APW exists, the balance will display
Put.10
, proceed to step 5.
3. Press NO to use the stored APW. Proceed to step 7.
4. Press YES to establish an APW.
5. The balance will then display the stored sample size,
Put 10
i.e. . Press NO or BACK to toggle the choices
(5, 10, 20, 50 or 100).
6. Put the indicated number of pieces on the platform
then press YES to calculate the APW. The display
shows the piece count.
7. Add additional pieces until the desired count is
reached.
8. To clear the stored APW, press and hold MODE
Count
until is displayed. Press YES when
displayed.
NOTE: Press FUNCTION to view the current APW.
PAGE 5 OF 33
OPERATION CONTINUED
WeIGH
(weigh)
Count
is displayed.
Clr.pwW

PERCENT WEIGHING

This mode measures the weight of a sample as a
percentage of a reference weight.
1. If required, place an empty container on the
platform and press TARE.
2. Press and hold MODE until
Clr.ref
(clear reference) will then display. If no
reference weight exists, the balance will display
Put.ref
, proceed to step 5.
3. Press NO to use the stored reference weight and
proceed to step 6.
4. Press YES to establish a new reference. Balance will
now display
5. Add the desired reference material to the platform
or container. Press YES to store the reference weight.
The display shows 100%.
6. Replace the reference material with the sample
material. The display shows the percentage of the
sample compared to reference weight.
7. To clear the stored reference, press and hold MODE
PERCNT
until
displayed.
NOTE: Press FUNCTION to view the current
reference weight.
CHECK WEIGHING
Use this mode to compare the weight of items to a
target weight range. The balance supports positive,
negative and zero check weighing.
1. Press and hold MODE until
CLr.ref
displayed.
display. If no limits exist, the balance will display
SEt.Lo, proceed to step 4.
2. Press NO to use the stored check limits and proceed
to step 6.
3. Press YES to establish new check limits.
4. The balance will then display
the low limit value. Press YES to accept or NO to edit
the low limit value. The stored value then displays with
the first digit highlighted
press NO until the desired number appears. Press YES
to accept and highlight the next digit. Repeat until all
the digits are correct. Press YES to accept the low limit
Set. Hi
value,
is
5. Repeat the same procedure to accept or edit the
high value.
Percnt
is displayed.
Put.ref
.
is displayed. Press YES when C
CHeCk
(check) is
(clear check limits) will then
Set.Lo.
00.000 kg.
will be displayed.
lr.ref
is
Press YES to view
Repeatedly
0218 IH-5848