Related Manuals for ENAR PC60
Summary of Contents for ENAR PC60
-
Page 1: Table Of Contents
6.1 INTRUCTIONS FOR ORDERING PARTS 6.2 INTRUCTIONS FOR REQUESTING GUARANTEES PLACAS E INDICATIVOS / PLATES AND INDICATIVES /PLAQUES ET INDICATEURS /PLATTEN UND KENNZEICHEN ESPECIFICACIONES TÉCNICAS / TECHNICAL DATA / SPECIFICATIONS TECHNIQUES / TECHNISCHE DATEN TAMPING RAMMERS PC60, PC65, PC70, PC80... -
Page 2: Preface
PREFACE We would like to thank our customers for the trust placed in the ENAR brand. It is important to read this manual to gain a full understanding of the characteristics and functions of the compactor. Before commencing work with this machine, or performing maintenance tasks on it, read, digest and observe all the safety instructions included in this manual. -
Page 3: Safety Information
ENARCO. ENARCO will be exempt from any liability deriving from failure to comply with this instruction. TAMPING RAMMERS PC60, PC65, PC70, PC80... -
Page 4: Safety During Operation Of The Machine
When being transported over long distances, it is highly recommended that the fuel tank be emptied beforehand. • The transport accessory has not been designed for standing the compaction plate on it and should only be used to move the equipment. TAMPING RAMMERS PC60, PC65, PC70, PC80... -
Page 5: Which Machine Is The Most Suitable For Each Application
Layer thickness 0 – 25 cm Layer thickness 20 – 40 cm Hot mortar Cold mortar Subgrade 40 – 100 mm Layer of boulders 25 – 60 mm # Can be used + Recommended TAMPING RAMMERS PC60, PC65, PC70, PC80... -
Page 6: Sound And Vibration Measurements
When the engine is hot, the air regulator should be half-open or completely open. If it proves difficult to start the engine, make sure that the air regulator lever is half-open to prevent the carburettor from flooding due to excess fuel. TAMPING RAMMERS PC60, PC65, PC70, PC80... -
Page 7: Operating The Machine
Before stopping the engine, leave it ticking over for two to three minutes and then press the stop button until the engine stops completely. 5.4.3. Close the fuel tap by putting the lever in a horizontal position. TAMPING RAMMERS PC60, PC65, PC70, PC80... -
Page 8: Maintenance Service And Storage
Incorrect separation between electrodes • There is no electricity in the high-tension cable Switch of detention button short-circuited Ignition coil defective Insulation of condenser deficient or short-circuited Ignition coil broken or short-circuited • Compression satisfactory Incorrect fuel TAMPING RAMMERS PC60, PC65, PC70, PC80... - Page 9 • Regulator spring faulty • Deficient fuel flow • Air entering tube suction system Starter functioning defectively - Rotating part clogged with dust - Helical spring faulty DIESEL ENGINE (AIR COOLED) Problems with starting: TAMPING RAMMERS PC60, PC65, PC70, PC80...
- Page 10 • Ignition defective accompanied by blank exhaust Piston, cylinder, ring worn out Injector blocked Upper and lower piston rings fitted the wrong way round Injection feed incorrectly set. Incorrect valve synchronization Injection pump joint is loose TAMPING RAMMERS PC60, PC65, PC70, PC80...
- Page 11 • Winding belt is uncoupled or slips • Clutch slips • Vibrator is jammed • If there is vibration but no movement, it could be that the vibrator is on a moist or slippery surface. Try on the appropriate surface. TAMPING RAMMERS PC60, PC65, PC70, PC80...
-
Page 12: In Case Of Failure
No piece of equipment will be covered by guarantee if it has been manipulated previously by personnel not connected to ENARCO, S.A. ENARCO, S.A., reserves the right to modify any part of this manual without prior notice. NOTA: TAMPING RAMMERS PC60, PC65, PC70, PC80... -
Page 13: Placas E Indicativos / Plates And Indicatives /Plaques Et Indicateurs /Platten Und Kennzeichen
ENAR STICKER AUTOCOLANT ENAR ANAGRAMM 107235 ENAR 80x80 80x80 ENAR 80x80 80x80 ANAGRAMA AUTOCOLANT RC6506 ENAR STICKER ENAR ANAGRAMM ENAR ENAR ADHESIVO STICKER ADHÉSIF KLEBSTOFF 107225 PRECAUCION PRECAUTION PRECAUTION ACHTUNG MUELLES SPRINGS RESSORTS SPRUNGFEDER TAMPING RAMMERS PC60, PC65, PC70, PC80... -
Page 14: Especificaciones Técnicas / Technical Data / Specifications Techniques / Technische Daten
HONDA YANMAR MOTEUR GX120 DKR EC12 D EH12 DU GX120 DKR L40 AE MOTOR LUBRICANTE MÁQUINA (L) MACHINE OIL (L) MORLINA 100 (1.8 L.) HUILE POUR MACHINE (L) DENSOLINA 100 (1.8 L.) MASCHINENOEL (L) TAMPING RAMMERS PC60, PC65, PC70, PC80... - Page 15 High resistant product, wich doesn´t need air to react and bears Green Loctite 601 the oil. 124154 – 6 oz. Producte anaérobie de rétention d’haute resistence, tolérant au Verte huile. Stoff von grösser widerstandskraft, der ohne sauerstoff reagiert Grün und das öl zulässt. TAMPING RAMMERS PC60, PC65, PC70, PC80...
Need help?
Do you have a question about the PC60 and is the answer not in the manual?
Questions and answers