Iget SECURITY M3P1 Installation Manual

Trigger Mode Clarification/ Funkce Trigger/ Funkcie Trigger
Trigger Mode Mód Triggeru Mód Triggeru Clarification
Close Zavřený Zatvorený Deactivated when triggered
Instant Okamžitý Okamžitý Activated when ARM/HOME ARM
24 Hours 24 Hodin 24 Hodín Activated even when DISARM
Home Režim Doma Režim Doma Deactivated when DISARM/HOME ARM
Door Chime Uvítací Gong Uvítací Gong No alarm but clanking
Delay Zpoždění Oneskorenie Wait few seconds before alarm
Battery replacement instructions/ Výměna baterie/
① Press down the hook on sensor with thumb, push it to open the cover.
① Stiskněte tlačítko dolů pomocí palce a druhou rukou otevřete kryt detektoru.
① Stlačte tlačidlo nadol pomocou palca a druhou rukou otvorte kryt detektora.
Exclusive importer of products Shenzhen Dinsafe Intelligence Co., Ltd.
for the Czech Republic and Slovak Republic
INTELEK spol. s.r.o., Vlárská 22, 627 00 Brno
SUPPORT: http: //www.iget.eu/helpdesk
Copyright © 2015 INTELEK spol. s r.o. All rights reserved.
Features
The M3P1 wireless motion sensor is an accessory of iGET SECURITY M3 series smart alarm system, mainly for indoor use. With
high performance infrared sensor, works under digital dual-core fuzzy logic operative programming and intelligent analysis,
it accurately detects human body movement and effectively avoids false alarms. Featured with automatic temperature
compensation technology, it ensures high intelligence, sensitivity, and stability. It's fashion design, energy saving, low battery
warning supported and with long transmission distance. The main panel will send a SMS to user for battery changing when
needed. With 360º angle adjustment supported, it's easy to setup and never get stuck.
Parameters
• Working Voltage
DC 3V
• Battery
2 × AA battery(1.5V)
• Working Current
22mA
• Standby Current 60μA
• Detective Range 110°
• Detective Distance
9m
• Transmission Distance
Without obstacle 100m
• Transmission Frequency 433.29MHz
• Working Temperature -10℃~40℃
• Humidity
≤90%rh (non-condensing)
• Weight
66g (battery not included)
• Dimension
99.6mm*54.0mm*40.2mm
Appearance
Detection Window
Stainless-steel Bead
r
LED Indicato
Význam Význam
Deaktivován pro všechny režimy alarmu Deaktivovaný pre všetky režimy alarmu
Aktivní když je režim alarmu Aktivován/ Aktívny keď je režim alarmu Aktivovaný /
Režim Doma Režim Doma
Aktívna vždy aj pri režime alarmu
Aktivní vždy i při režimu alarmu Deaktivace
Deaktivácia
Neaktivní pokud je režim alarmu Deaktivace/ Neaktívne ak je režim alarmu Deaktivácia /
Režim Doma Režim Doma
Bez alarmu, ale uvítací gong (např. pro Bez alarmu, ale uvítací gong (napr. pre
obchody) obchody)
Čaká niekoľko sekúnd pred aktiváciou
Čeká několik vteřin před aktivací alarmu
Výmena batérie
② Replace with 2x AA battery.
② Vyměňte 2x AA baterie.
② Vymeňte 2x AA batérie.
112g (battery included) 62.3g (Bracket)
L*W*H(±0.1mm)
Trigger Button
Magnetic Slice
Bracket
alarmu
Installation manual
Instalační manuál
Inštalačný manuál
PCB Layout
On/Off Switch
Installation & Notice
• Open the case and remove the battery insulative strip.
• Pairing with main panel by App before installing.
• Fix the bracket with double-side sticky tape or screws on wall, connect the sensor to bracket, adjust a
proper angle. 360° angle adjustment is easily available with connection of bead and magnetic slice.
• Recommended to install at height of 1.8-2.2m from ground, with gradient 10°~20°.
• Indoor use only. Avoid installing the sensors in area with strong light, temperature changes rapidly or
the air stream flows frequently, like close to windows, air conditioner, refrigerator, heater, oven, and
large obstacles.
• Aovid installing two sensors in the same detection scope to interference.
• The sensor is more sensitive to the cross movement than to the vertical movement, so the perference
of sensor is best when the detection direction is vertical to the walking direction of people.
10°-20°
1.8-2.2m
SECURITY M3P1
Wireless Motion Sensor
|
| Pohybový PIR detektor
| Pohybový PIR detektor
Website : www.iget.eu E-mail : sales@iget.eu
Operating Instructions
1. Working principle
with digital dual-core fuzzy logic operative pro-
Infrared Sensor
gramming and intelligent analysis, it accurately
detects human body movement with infrared
sensor and sends signal to main panel.
2. Pairing with main panel by App
① Scan the QR code printed on the sensor.
② The pairing result would be confirmed by SMS
Detective Interval Time
sent from main panel.
Setting Switch
(every 5s. or 5min.)
1.2m 6m
Detection blind zone
12m