Advertisement
Daily Cleaning Instructions: KL1Plus
Clean the following components at least once daily. Clean more frequently if your pharmacy dispenses
many dust‐generating medications or if you experience counting errors.
Materials: 70% isopropyl alcohol or mild soap (e.g., dish soap), lint‐free cloth or paper towels, computer
screen cleaner. Do not use facial tissue, cotton balls or cotton swabs.
Before starting, turn off the unit and unplug it.
1. Funnel
A. Remove the funnel from the unit.
B. Clean outside and inside thoroughly with alcohol or mild soapy water.
2. Glass Detector Windows
The unit's counting sensors are located behind the removable inside channel
assembly. Most counting errors are caused by pill dust accumulating on the edges
and corners of the glass windows on the inside channel assembly. Clean the windows well.
A. Unscrew the two round thumb screws on top of the unit. Remove the square guard.
B. Lift out the entire inside channel assembly.
C. Wipe off excess pill dust on the inside of the four glass windows with a dry cloth.
D. Wet a clean cloth with alcohol or mild soapy water and clean the inside of the four
glass windows thoroughly to remove all remaining dust and residue. Carefully wipe
back‐and‐forth, not up‐and‐down. Do not press hard as this may break the glass
windows. Do not remove the individual glass panes unless Service instructs you to.
E. Fold the cloth to form a "point" to carefully clean any edge or corner where dust can
accumulate. Pay special attention to corners.
F. Wipe the glass windows dry with a clean cloth. Hold the inside channel assembly up
to a light to visually inspect the glass windows for any dust, fingerprints, or streaks.
Re‐clean if necessary. Wipe dry.
G. Look down inside the device and visually inspect the four inside glass windows for dust
or streaks. If necessary, clean with water and wipe dry.
H. Replace the inside channel assembly and square guard. Tighten the two round thumb
screws until snug. Do not over‐tighten the thumb screws.
I.
If desired, the glass window holder can be removed from the inside channel assembly
for a more thorough cleaning and visual inspection. Gently push down on the square
sliding ring, which spreads the two black clips holding the glass window holder. Take
special care not to break the black clips.
3. Counting Tray
Clean thoroughly with mild soapy water. Do not use alcohol.
Touch Screen
Funnel
Square
Guard
Tray
Steps 2C‐F – Inside
Channel Assembly:
Clean inside and
outside of 4 glass
windows without
removing or damaging
the panes
Step 2I – Visually
Inspect Glass
Windows
5BIM‐380201‐DCI 5/2016
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Kirby Lester KL1Plus
Summary of Contents for Kirby Lester KL1Plus
- Page 1 Daily Cleaning Instructions: KL1Plus Clean the following components at least once daily. Clean more frequently if your pharmacy dispenses many dust‐generating medications or if you experience counting errors. Materials: 70% isopropyl alcohol or mild soap (e.g., dish soap), lint‐free cloth or paper towels, computer screen cleaner. Do not use facial tissue, cotton balls or cotton swabs. Before starting, turn off the unit and unplug it. Funnel Square 1. Funnel Touch Screen Guard A. Remove the funnel from the unit. B. Clean outside and inside thoroughly with alcohol or mild soapy water. Tray 2. Glass Detector Windows The unit’s counting sensors are located behind the removable inside channel assembly. Most counting errors are caused by pill dust accumulating on the edges and corners of the glass windows on the inside channel assembly. Clean the windows well. A. Unscrew the two round thumb screws on top of the unit. Remove the square guard. B. Lift out the entire inside channel assembly. C. Wipe off excess pill dust on the inside of the four glass windows with a dry cloth. D. Wet a clean cloth with alcohol or mild soapy water and clean the inside of the four glass windows thoroughly to remove all remaining dust and residue. Carefully wipe back‐and‐forth, not up‐and‐down. Do not press hard as this may break the glass windows. Do not remove the individual glass panes unless Service instructs you to. E. Fold the cloth to form a “point” to carefully clean any edge or corner where dust can Steps 2C‐F – Inside ...
- Page 2 3. Counting Tray Clean thoroughly with mild soapy water. Do not use alcohol. 4. Tray Sensor Located on the KL1Plus behind the counting tray when the tray is fully inserted. This sensor tells the unit that the tray is properly seated. With the tray removed, clean the sensor window with water. Wipe dry to remove streaks. Step 4 – 5. As Needed: Clean Touch Screen Tray Sensor As needed, carefully clean with a non‐ammonia glass cleaner or a computer screen cleaner and a clean, lint‐free cloth. Do not spray any liquid directly onto the touch screen. Instead, spray onto the cloth first. 6. Customize Onscreen Cleaning Reminders You can customize the automatic cleaning reminder function of your KL1Plus. See the KL1Plus operating manual for full instructions on making these adjustments: Turn the cleaning checklist off Change the frequency of the cleaning reminder (default 150 scripts) Add medications that automatically trigger a cleaning reminder (e.g., sulfa) Note about the use of mild soapy water versus isopropyl alcohol: Mild soapy water and alcohol both provide appropriate sanitary cleansing. Water leaves fewer streaks than alcohol on a Kirby Lester device's inside glass windows. If streaks are found after cleaning, use just water and wipe dry. In general, prolonged alcohol exposure causes faster wear‐and‐tear on plastic. 7. Cleaning and Troubleshooting Problem or Error Code Probable Cause Possible Solution(s) In KL1 Mode only: E‐2, E‐4, E‐9, O‐S Tablet dust or residue on glass windows, or Clean glass windows thoroughly. Or replace ...
Need help?
Do you have a question about the KL1Plus and is the answer not in the manual?
Questions and answers