Elmo CRA-2 Quick Start Manual

Wireless Pen Tablet
CRA-2 Quick Start Guide
● PACKAGE CONTENTS
□ Pen
□ Tablet
（CRA-2）
□ Pen holder
● PREPARATION
● Charging
Connect the tablet to a computer with
the supplied USB cable.
Status LED
Charging: Red
Fully charged: Off
● Connecting to a device
Use the supplied wireless dongle to connect the tablet to a device wirelessly.
Connecting to a computer
You can control your computer like a
mouse. By using with the EIT, you can
add annotations to the screen image.
Insert the wireless
dongle to the USB
port of the computer.
※ You can also use the tablet by connecting it to a device using the supplied USB cable.
6X1xxxx01 R0-Xxx
□ USB cable
□ Wireless
(For charging or
Dongle
for connecting to
a device)
（This book ）
□ Quick Start
□ Extra core x 8
Guide
( ※ Extra cores are
□ IMPORTANT
in the pen holder.)
SAFEGUARDS
●接続端子・スイッチを確認する
● Checking the connection ports and
switches
Side view (left)
USB port
Storage for
the wireless
Wireless switch
dongle
※ The wireless switch will be
used only when the tablet
is connected wirelessly.
Connecting to the document camera
You can add annotations to the document
camera image or control the document camera.
Insert the wireless dongle to
the USB port of the document
camera.
● USING THE PRODUCT
1. Turn on the power.
The Status LED will turn green and go off
after the power is on.
Status
LED
● When connecting wirelessly
⇒ The tablet will power on when the
wireless switch is set to on.
ON（Enabled）
By connecting the wireless dongle to a computer
or document camera, you can use the CRA-2
wirelessly.
OFF（Disabled）
The power enters standby mode.
※ You can use the tablet no matter the wireless
switch is on or off when connecting with the
USB cable.
● When connecting with the USB cable
⇒ The tablet will power on when it is
connected to a running computer or
document camera.
2. Operate the tablet
Working area
The tablet will start to
recognize the pen if the
working range is touched
by the pen tip button.
The tablet will enter sleep
mode after about 45
minutes of inactivity.
※ Only when connected
wirelessly
● Replacing the pen tip
When the pen tip becomes round, replace it with the supplied "extra
core". Use the supplied pen holder when replacing the pen tip.
＜ Step1 ＞ ＜ Step2 ＞
②
Cover
①
Pen holder
※ Caution
・When replacing the pen tip, be sure to replace it with the supplied "extra core".
・Make sure that children do not put small parts into their mouths.
● DETAILED USAGE OF THE PRODUCT
For detailed information about the Instruction Manual, refer to the following website:
https://www.elmousa.com/
● Pen operations
Right click
(when using with the document camera
: eraser)
When using with the
document camera
: eraser
Left click
● Shortcut keys
※ You need to install the EIT on your computer
to use the tablet with your computer. Available
functions may differ depending on the document
camera used.
①
②
③
④
⑤
Name Description
Document
①
To display the document camera image.
camera mode
Whiteboard
②
To display the whiteboard screen.
mode
Playback
③
To display images stored.
mode
・When connecting to a computer:
④ Operation/ to control a computer as a mouse
Settings mode ・When connecting to the document
camera: to configure pen settings
・When connecting to a computer:
⑤ to close the EIT
Close/ Hide
・When connecting to the document
camera: to display or hide menus
● Storage for the pen and wireless dongle
Pen storage
Storage for the wireless dongle
Slide and push the dongle into
the storage.Push the dongle
with your finger to take it out.
Storage for the pen
Insert the pen from the pen tip
into the storage.
Pull the pen with your finger to
take it out.
Step1.Rotate the pen holder counterclockwise
＜ Step3 ＞
(arrow ① ) and remove the cover (arrow ② ).
Step2.Put the pen to the center of the pen holder.
Tilt the pen to remove the pen tip.
Step3.Insert the extra core firmly into the pen until
it stops.
https://www.elmoeurope.com/index.php/en/
※ Available functions
may differ depending
on the document
camera used.