Page 1
Venice - Large Corner TV Unit Assembly Instructions - 450/9071 Please keep for future reference 459/9641 Dimensions Width - 119.8cm Depth - 39.19cm MADE IN Height - 51.2cm BRITAIN Important - Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928.
Page 2
Safety and Care Advice Important - Please read these instructions fully before starting assembly • Warning: This unit weighs • Make sure you have enough • We do not approximately 25kgs. space to layout the parts before recommend the Please lift with care. starting.
Page 3
Components - Panels If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 When applicable, remove any Please check you have all the panels listed below protective film before use...
Page 4
Components - Fittings If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly.
Page 5
Assembly Instructions Step 1 Note: The right drawer front has a small identification hole. Prepare the 2 drawer fronts Screw 2 metal dowels into each of the drawer fronts Note: Tighten the metal dowels up fully against the panels. Step 2 Prepare the drawer sides Insert a small locking...
Page 6
Assembly Instructions Step 4 Fit the drawer base Slide the drawer base down the grooves in the drawer sides and down into the groove in the drawer front Step 5 Fit the drawer back Fit the drawer back between the drawer sides Make sure that the drawer base...
Page 7
Assembly Instructions Step 8 Prepare the top Screw 4 metal dowels into the top Screw 4 small metal dowels into the holes on the top Note: Tighten metal dowels up fully against the panels. Step 9 Prepare the top divider Insert 2 large locking nuts into the...
Page 8
Assembly Instructions Step 11 Prepare the 2 horizontals Insert 4 large locking nuts into each of the 2 horizontals Step 12 Fit a horizontal Attach a horizontal the top divider using 2 screws Note: Support the horizontal until the right Step 13 side has been fitted.
Page 9
Assembly Instructions Step 14 Prepare the right side Place a runner onto one of the sides Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw Slide the runner back the other way and fit the 2nd screw into the corresponding hole...
Page 10
Assembly Instructions Step 15 Fit the right side Push the right side onto the top and the horizontal The 2 small metal dowels fitted to the top must slide into the top of the 2 hollow core locking nuts fitted to the right side .
Page 11
Assembly Instructions Step 16 Prepare the lower divider Place a runner Finished onto the lower divider front edge Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw Finished Slide the runner front edge back the other way and use the 2nd hole from...
Page 12
Assembly Instructions Step 17 Finished Fit the lower divider front edge Push the lower divider down onto the horizontal Step 18 Fit the other horizontal Fit the horizontal the right side and the lower divider Attach the horizontal to the lower divider using 2 screws Use a screwdriver to tighten the 2 large...
Page 13
Assembly Instructions Step 19 Prepare the plinth Insert 2 large locking nuts into the plinth Tap 2 wooden dowels into the plinth Step 20 Fit the plinth Push the plinth onto the right side Use a screwdriver to tighten the large locking fitted to the plinth...
Page 14
Assembly Instructions Step 21 Prepare the left side Place a runner onto one of the sides Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw Slide the runner back the other way and fit the 2nd screw into the corresponding hole...
Page 15
Assembly Instructions Step 22 Fit the left side Push the left side onto the assembly. Use a screwdriver to turn the nuts inside the 2 hollow core locking nuts fitted to the left side Use a screwdriver to tighten the 5 large locking nuts fitted to the horizontals...
Page 16
Assembly Instructions Step 25 Secure the back Secure the back the 2 horizontals using 4 screws Carefully stand the unit up for the next step. Warning: The unit is heavy. Lift with care. Step 26 Fit the drawers Remember: The right drawer front has a Slide both the runners small identification hole...