Sealey TR1000.V3 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear Protective
instruction Gloves
manual
1. SAFETY
ELECTRICAL SAFETY
1.1.
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired
8
or replaced is repaired replaced immediately by a qualified electrician.
1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2. GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this
‰
transformer.
Familiarise yourself with the application and limitations of the transformer, as well as the potential hazards.
9
WARNING! Disconnect the transformer from the mains power before performing any maintenance.
‰
Maintain the transformer in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
9
WARNING! DO NOT connect to mains if any parts are damaged or missing as this may cause failure and/or personal injury.
‰
Keep the transformer clean for best and safest performance.
9
Keep children and unauthorised persons away from the working area.
9
DO NOT use the transformer for any purpose other than that for which it is designed.
8
DO NOT exceed the rated capacity of the transformer.
8
DO NOT allow untrained persons to use the transformer.
8
DO NOT use the transformer when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT pull the plug from the power supply by the cable.
8
When not in use unplug from the mains power supply and store in a safe, dry, childproof area.
9
2. INTRODUCTION
i
110V Transformer with tool rated performance suitable for intermittent running of power tools and continuous running of lighting products within
specified capacity. IP44 Rated unit with case manufactured from GRP and insulated to class H. Fitted with thermostatic overload protection.
Supplied with 16Amp/110V socket(s) and 1.2mtr flexible three-core cable.
© Jack Sealey Limited
INSTRUCTIONS FOR
MODEL NO:
TR1000.V3, TR1500.V3, TR2000.V3, TR3000.V3
Isolating Warning:
Transformer Electricity
Original Language Version
TOOL TRANSFORMERS
Warning:
Hot surface
TR1000.V3, TR1500.V3, TR2000.V3, TR3000.V3 Issue 4 (3) 14/05/18
Recommended fuse rating
13 Amp