Right Of Complaint - RUSTA 901512890101 Manual

Maintenance
Maintenance
Fig 7
Fig 7
1. Change the dust bag: when the indicator turns to be red, it is time to repla
1. Change the dust bag: when the indicator turns to be red, it is time to replace with a
(Fig 10)
(Fig 10)

Open the front cover by clipping. (Fig 11)

MAINTENANCE
Maintenance
Maintenance

1. Change the dust bag: when the indicator turns to be red, it is time to replace with a new bag.
1. Change the dust bag: when the indicator turns to be red, it is time to replace with a new bag. Take out the bag holder then remove the full dust bag. (Fig 12)

• Change the dust bag: When the indicator turns red, it is time to replace with a new bag.
(Fig 10)
(Fig 10)
Install the dust bag: insert the dust bag into the bag holder and then put
(Fig. 10).
Install the dust bag: insert the dust bag into the bag holder and then put it in the s
cabinet.(Fig 13)
Open the front cover by clipping. (Fig 11) Open the front cover by clipping. (Fig 11)
 
• Open the front cover by clipping. (Fig. 11).
cabinet.(Fig 13)
Take out the bag holder then remove the full dust bag. (Fig 12)
Take out the bag holder then remove the full dust bag. (Fig 12)


If the dust bag is not installed, the front cover can't be closed.
• Take out the bag holder then remove the full dust bag. (Fig. 12).
If the dust bag is not installed, the front cover can't be closed.
Install the dust bag: insert the dust bag into the bag holder and then put it in the slot
Install the dust bag: insert the dust bag into the bag holder and then put it in the slot
• Install the dust bag: Insert the dust bag into the bag holder and then put it in the slot
2. Inlet filter: clean the filter with warm water once a year and you can instal
cabinet.(Fig 13)
cabinet.(Fig 13)
2. Inlet filter: clean the filter with warm water once a year and you can install it after d
cabinet.(Fig 13) NOTE! If the dust bag is not installed, the front cover can't be closed.
is damaged, a new filter should be replaced .(Fig 14)
If the dust bag is not installed, the front cover can't be closed.
If the dust bag is not installed, the front cover can't be closed.
is damaged, a new filter should be replaced .(Fig 14)
• Inlet filter: Clean the filter with warm water once a year and you can install it after dry.
3. Exchange the inlet filter: clip down and remove the inlet cover by hands f
2. Inlet filter: clean the filter with warm water once a year and you can install it after dry. If the filter
2. Inlet filter: clean the filter with warm water once a year and you can install it after dry. If the filter
If the filter is damaged, a new filter should be replaced .(Fig 14)
3. Exchange the inlet filter: clip down and remove the inlet cover by hands for exchan
is damaged, a new filter should be replaced .(Fig 14)
filter.(Fig 15)
is damaged, a new filter should be replaced .(Fig 14)
• Exchange the inlet filter: Clip down and remove the inlet cover by hands for exchange
filter.(Fig 15)
3. Exchange the inlet filter: clip down and remove the inlet cover by hands for exchange of
3. Exchange the inlet filter: clip down and remove the inlet cover by hands for exchange of
of filter.(Fig 15) 4. Clean the filter: open the front cover and draw out the HEPA frame and fi
filter.(Fig 15)
4. Clean the filter: open the front cover and draw out the HEPA frame and filter. Was filter.(Fig 15)
it after dry(Fig 16/17).
• Clean the filter: Open the front cover and draw out the HEPA frame and filter. Wash it
4. Clean the filter: open the front cover and draw out the HEPA frame and filter. Wash it and install it after dry(Fig 16/17).
4. Clean the filter: open the front cover and draw out the HEPA frame and filter. Wash it and install
and install it after dry (Fig 16/17).
it after dry(Fig 16/17).
it after dry(Fig 16/17).
Fig. 10
Fig 10
Fig 10
Fig 10
Fig 10
Fig. 14
Fig 14
Fig 14
Fig 14 Fig 14
WARNING!
The plug must be removed from the power socket before any maintenance
Warning
Warning
Warning Warning
or replacement. If the power cord is damaged, it may only be replaced by the factory, a
The plug must be removed from the power socket before any maintenance or replacement.
The plug must be removed from the power socket before any maintenance or replacement.
The plug must be removed from the power socket before any maintenance or replacemen The plug must be removed from the power socket before any maintenance or replac
maintenance centre or similarly qualified person.
If the power cord is damaged, replace them only by the factory or maintenance center or
If the power cord is damaged, replace them only by the factory or maintenance center or
If the power cord is damaged, replace them only by the factory or maintenance center or If the power cord is damaged, replace them only by the factory or maintenance cente
similarly qualified persons. similarly qualified persons.
similarly qualified persons. similarly qualified persons.

RIGHT OF COMPLAINT

By law the product must be returned to the place of purchase along with the original
receipt in the event of a complaint. The user is liable for any damage to the product that
is caused by not using the product for its intended purpose or by not following this user
manual correctly. The right of complaint will not apply in these instances.
INFORMATION ABOUT HAZARDOUS WASTE
Used products should be handled separately from
household waste. They should be taken for recycling in
accordance with local rules for waste management.
Fig 8
Open the front cover by clipping. (Fig 11)
Take out the bag holder then remove the full dust bag. (Fig 12)
Fig. 11
Fig 11
Fig 11
Fig 11
Fig. 15
Fig 15
Fig 15
Fig 15
Fig 8
Fig. 12
Fig 12
Fig 12
Fig 11
Fig 16
Fig 16
Fig 15
Fig 9
Fig 9
Fig 13
Fig 13
Fig 12
Fig 12
Fig. 16
Fig 16 Fig 16
Fig. 13
Fig 1
Fig. 17
Fig 17
Fig 17
Fig 17 Fig 17
5