Table of Contents
Advertisement
Quick Links
Quest H5
Quest Dry
Installation, Operation and Maintenance Instructions
Installation, Operation and Maintenance Instructions
– Read and Save These Instructions –
This manual is provided to acquaint you with the
Quest H5 air mover so that installation, operation
and maintenance can proceed successfully. Ultimate
satisfaction depends on the quality of set up and
a thorough understanding of this equipment. The
Quest H5 is built around tested engineering principles
and has passed a thorough inspection for quality of
workmanship and function.
Quest H5:
• Compact design
• Variable speed flow
• Multiple ducting options
• Tough, plastic cabinet
• Optional carbon filter
Specifications subject to change without notice.
4201 Lien Rd
Madison, WI 53704
www.QuestClimate.com
1
Patent Pending
Phone 608-237-8400
Toll-Free 1-877-420-1330
info@QuestClimate.com
TS-986
02/20 Rev. B
Advertisement
Table of Contents
Summary of Contents for Quest Engineering H5
- Page 1 Installation, Operation and Maintenance Instructions – Read and Save These Instructions – This manual is provided to acquaint you with the Quest H5 air mover so that installation, operation and maintenance can proceed successfully. Ultimate satisfaction depends on the quality of set up and Patent Pending a thorough understanding of this equipment.
-
Page 2: Table Of Contents
Introduction .........................1 Specifications ......................2 Important Safety Instructions .................. 2 Operation ........................2 3.1 Transporting the Quest H5 ................2 3.2 Electrical Requirements ..................2 3.3 Air Ducting ......................3 3.3A Inlet Ducting ....................3 3.3B Outlet Ducting ................... 3 3.3C Negative Air Ducting ................ -
Page 3: Specifications
3.2 Electrical Requirements The Quest H5 HEPA System can be plugged into a grounded 15 Amp circuit. It draws about 2.4 Amps with clean filters and no ducting. The amp draw will decrease slightly with added ducting and as the filters load with particulate.Due to the presence of GFCI receptacle, the unit must be plugged directly into a wall outlet. -
Page 4: Air Ducting
3.3C Negative Air Ducting The Quest H5 HEPA System can be used to filter and exhaust air from a space. When exhausting to outside the space, the space will be under a slight negative pressure. This will help prevent airborne particles from leaving the space, because the negative pressure will draw air in through openings in the space’s exterior surfaces. -
Page 5: Resettable Circuit Breaker
GFCI duplex outlet. If operating properly the “RESET” button on the GFCI outlet will pop out. A tripped GFCI is indicated by a small LED. The device can only be “RESET” when the H5 is connected to a wall outlet providing standard voltage. -
Page 6: B Optional Activated Carbon/Potassium Permanganate Filters
The filter is the same size as the pleated fabric filter. Install it in place of the pleated fabric filter. 5. Service CAUTION: Servicing the Quest H5 HEPA System with its high voltage circuitry presents a health hazard that could result in death, serious bodily injury, and/or property damage. Disconnect the appliance from the power supply before servicing. -
Page 7: Wiring Diagram
Quest H5 Installation, Operation and Maintenance Instructions 6. Wiring Diagram BLOWER SPEED CNTRL TRIAC FILTER PRESSURE CHECK SWITCH LIGHT 120v 60Hz single phase 7. Service Parts Item Part No. Description 4031877 Air Filter, Pleated, 1” x 18” x 18” 4031864 Air Filter, HEPA, 2.5”... - Page 8 Quest H5 Installation, Operation and Maintenance Instructions 1-877-420-1330 www.QuestClimate.com info@QuestClimate.com...
- Page 9 If any Quest H5 part is repaired or replaced, the new part shall be warranted for the balance of original warranty (but all warranty periods will be extended by the period of time, if any, that the Quest H5 with FOCUS Technology is out of service while awaiting covered warranty service).