Related Manuals for v.LOGiC V5-NBT-PNP
Summary of Contents for v.LOGiC V5-NBT-PNP
- Page 1 Intelligent Solution Interface V5-NBT-PNP Compatible for the F-series BMW with navigation system or radio and 6.5”, 7”, 8.8” or 10.25” monitor with 4+2pin HSD2 LVDS connector Version 26.11.2019 V5-NBT-PNP...
- Page 2 • Picture-in-picture mode combining after-market rear-view and front camera picture(s) with factory parking sensor graphics • Interactive lane lines • Compatible with all factory video accessories (e.g. rear-view camera, Top-View, nightvison, DVD-changer, TV-tuner) • USB update-port for software-updates by consumer Version 26.11.2019 V5-NBT-PNP...
-
Page 3: Table Of Contents
OSD – Additional setting options 4.2. Video-in-motion function 4.3. Selecting the interface as current video source 4.4. Controlling of the connected SMART-LINK module 4.4.1. Controlling by iDrive High 4.4.2. Controlling by iDrive Low 5. Specifications 6. Connections (interface-box) 7. Technical support Version 26.11.2019 V5-NBT-PNP... - Page 4 To receive a free update, the interface must be sent in at own cost. Labor cost for and other expenses involved with the software-updates will not be refunded. Version 26.11.2019 V5-NBT-PNP...
-
Page 5: Prior To Installation
Check compatibility of vehicle and accessories Requirements Navigation F-series with navigation system or radio with 6.5”, 7”, 8.8“ or 10.25“ monitor with 4+2pin HSD2 LVDS connector Note ”PDC – picture in picture” and “interactive lane lines” function is not simultaneously usable Version 26.11.2019 V5-NBT-PNP... -
Page 6: Setting The Dip Switches Of The Interface-Box V5C-M637
7“ monitor (ver.2) 8.8“ monitor 10.25“ monitor (ver.1) 10.25“ monitor (ver.2) After each change of the dip switch settings you have to execute a power reset of the interface-box! 1.4. LED‘s of the interface-box V5C-M637 Valid%input source CAN%ok Power Version 26.11.2019 V5-NBT-PNP... -
Page 7: Connection Schema
2. Connection schema Version 26.11.2019 V5-NBT-PNP... - Page 8 Back of factory monitor LVDS cable CAB-HSD2-RR148 Interface-box V5C-M637 FRONT 4+2Pin HSD2 LVDS female vehicle harness Version 26.11.2019 V5-NBT-PNP...
-
Page 9: Installation
Quadlock connector of harness TV-BM01 at the same position. Connect female Quadlock connector of vehicle harness to the male Quadlock connector of harness TV-BM01. Connect female Quadlock connector of harness TV-BM01 to the male Quadlock connector of the navigation computer Version 26.11.2019 V5-NBT-PNP... -
Page 10: Special Case Bmw I3
4+2pin HSD2 LVDS connector (LVDS-IN) on the front of the interface-box V5C-M637. Connect the second female 4+2pin HSD2 LVDS connector of the LVDS cable CAB-HSD2-RR148 to the male 4+2pin HSD2 LVDS connector of the factory monitor. Version 26.11.2019 V5-NBT-PNP... -
Page 11: After-Market Front Camera
The pink wire of harness V5C-UNI01 can be used for +12V electric power supply (max. 1A) of the after-market front camera. Configure in the OSD- menu “OPTION”, menu item “POWER OUT 1” the designated electric power supply (see chapter “Configurable switching outputs”). Version 26.11.2019 V5-NBT-PNP... -
Page 12: Settings For Connecting An After-Market Front Camera
(e.g. radio). After deactivation you can’t enable the parking process again until the vehicle is diving faster than 20km/h, the ignition is switched off and on or the PDC will be disabled and enabled again, if existing. Version 26.11.2019 V5-NBT-PNP... -
Page 13: After-Market Rear-View Camera
The green wire of harness TV-BM01 can be used for +12V electric power supply (max. 1A) of the after- market rear-view camera. Configure in the OSD- menu “OPTION”, menu item “POWER OUT 2” the designated electric power supply (see chapter “Configurable switching outputs”). Version 26.11.2019 V5-NBT-PNP... -
Page 14: Settings For Connecting An After-Market Rear-View Camera
The interface turns off, if PDC or reverse gear INPUT is enabled and it displays factory rear-view camera and/or PDC-display For vehicles with PDC button. Enabled while OPTION PARK LOGIC parking process and up to 20 km/h or together with PDC if existing Version 26.11.2019 V5-NBT-PNP... -
Page 15: Smart-Link
SMART-LINK module. Configure in the OSD- menu “OPTION”, menu item “Power Out 1” the setting “CAN” (see also chapter “Configurable switching outputs”). Connect the SMART-LINK interface control port “STA-UART” (available separately) to the "SMART-LINK CarPlay® Android Auto®" socket of V5C-UNI01 harness.. Version 26.11.2019 V5-NBT-PNP... -
Page 16: Smart-Link Audio Connection
You have to configure some settings in the OSD-menu INPUT if you want to connect the SMART-LINK module (Operation of the OSD: see chapter “OSD-Operation”). OSD-menu Menu item Setting Explication No front camera/SMART-LINK connected INPUT Enables the " FRONT CAM" input and control SmartPhone for the SMART-LINK set Version 26.11.2019 V5-NBT-PNP... -
Page 17: Configurable Trigger Outputs
+12V when ignition is on +12V when the rear-view camera input is POWER OUT1 activated (pink) OPTION POWER OUT2 RGEAR +12V when reverse gear is engaged (green) +12V when interface video-source is active (for external audio switch) Trigger putput deactivated Version 26.11.2019 V5-NBT-PNP... -
Page 18: Interactive Lane Lines
(Operation of the OSD: see chapter “OSD-Operation”). OSD-menu Menu item Setting Explication RVC LINES LINES Interactive lane lines activated 1/2/3/4/5/6/7/ OPTION CAR TYPE X1/X3/X4/X5/X6/ Vehicle type selection Z4/i3 Note: ”PDC – picture in picture” and “interactive lane lines” function is not simultaneously usable. Version 26.11.2019 V5-NBT-PNP... -
Page 19: Picture Settings
= 24:10 video full screen mode zoom -AV+LVDS = 16:9 video on left side, factory picture on right side - 6.5” and 7” 16:9 monitor: -FULL = 16:9 video full screen mode -ZOOM = 16:9 video full screen mode - zoom Version 26.11.2019 V5-NBT-PNP... -
Page 20: Operation
You can change the basic configurations of the interface in the OSD (on screen display). 4.1.1. OSD – Operation You can control the OSD by iDrive. 4.1.1.1. iDrive High Options Options Back OK OK Long press = enter OSD Short press= leave OSD Options Version 26.11.2019 V5-NBT-PNP... -
Page 21: Idrive Low
OSD menu „OPTION“ – „IDRIVE“ is for setting the right iDrive control knob. OSD-menu Menu item Setting Explication Vehicles with iDrive Low control knob OPTION IDRIVE Vehicles with iDrive High control knob HIGH iDrive High iDrive Low Version 26.11.2019 V5-NBT-PNP... -
Page 22: Osd - Additional Setting Options
Resetting to factory settings 4.2. Video-in-motion function It is possible to activate and deactivate the video-in-motion in the OSD menu “OPTION” (Operation of the OSD: see chapter “OSD-Operation”). OSD-menu Menu item Setting Explication Video-in-motion activated OPTION Video-in-motion deactivated Version 26.11.2019 V5-NBT-PNP... -
Page 23: Selecting The Interface As Current Video Source
The exiting of the video interface level is achieved by long press of MEDIA / AUDIO button or short press of RADIO / MENU / TEL / NAV button. Note: Activation of the AUX level is not necessary for camera view. Version 26.11.2019 V5-NBT-PNP... -
Page 24: Controlling Of The Connected Smart-Link Module
The picture shows which functions of the connected SMART-LINK module can be executed by iDrive control panel. Once the FVC/SmartPhone input is activated the iDrive control panel action will execute the function described in the picture. 4.4.1. Controlling by iDrive High Version 26.11.2019 V5-NBT-PNP... -
Page 25: Controlling By Idrive Low
4.4.2. Controlling by iDrive Low Version 26.11.2019 V5-NBT-PNP... -
Page 26: Specifications
Mini USB 7. Technical Support Caraudio-Systems Vertriebs GmbH manufacturer/distribution In den Fuchslöchern 3 D-67240 Bobenheim-Roxheim email support@caraudio-systems.de Legal disclaimer: Mentioned company and trademarks, as well as product names/codes are registered trademarks ® of their corresponding legal owners. Version 26.11.2019 V5-NBT-PNP...
Need help?
Do you have a question about the V5-NBT-PNP and is the answer not in the manual?
Questions and answers