Page 1 BUILT WITH QUALITY AND DESIGN FIRST WHOLE TREE CHIPPER ATTENTION: Depending on what replacement MODEL 1850 parts you are ordering, we will need the following information: OPERATING & PARTS MANUAL CHIPPER COMPONENTS Serial Number 1850 Model Number of Chipper Model No: _________________...
Page 2 CALIFORNIA PROPOSITION 65 WARNING ADVERTENCIA Breathing diesel engine Respirar gases de escape de exhaust exposes you to motores diesel expone chemicals known to the quÍmicos conocidos por el estado State of California to cause de California como causales de cancer and birth defects or cáncer y defectos congénitos u other reproductive harm.
Page 3 Copyright 3-15 FORM #WV-117 IT IS VERY IMPORTANT THAT THIS FORM IS FILLED OUT COMPLETELY & ACCURATELY. IF WE CANNOT READ THE PURCHASER’S INFORMATION OR IT IS INCORRECT, OUR CUSTOMER LIST WILL NOT BE ACCURATE. IMPORTANT - THIS FORM MUST BE RETURNED TO THE Customer Data Department 6750 Millbrook Road CUSTOMER DATA DEPARTMENT WITHIN TEN (10)
Page 4 Copyright 3-05 FORM #Q-111 DATE PURCHASED: _________________ TO BE RETURNED AFTER THIRTY (30) DAYS OF OPERATION MODEL: ___________________________ Please return to: Customer Data Department SERIAL NUMBER: ___________________ 6750 Millbrook Road DEALER NAME: ____________________ Remus, MI 49340 ___________________________________ (800) 952-0178 in USA (989) 561-2270 FAX: (989) 561-2273 E-MAIL: www.banditchippers.com...
Page 5: Table Of Contents
MODEL 1850 TABLE OF CONTENTS TABLE OF CONTENTS PAGES INTRODUCTION & WARRANTY ............SERIAL NUMBER LOCATION ............SAFETY PROCEDURES ..............EQUIPMENT SPECIFICATIONS ............DECALS .................... AUTOFEED OPTIONS ..............21 CONTROLS..................TRANSPORTATION PROCEDURES ..........MAINTENANCE ................HYDRAULIC SECTION ............CHIPPER SECTION ..............
Page 6: Introduction & Warranty
INTRODUCTION & WARRANTY INTRODUCTION The purpose of this manual is to provide the user with specifications and procedures for the operation, maintenance and repair of this BANDIT product. As with any piece of equipment, safety should always be a constant thought while the machine is being operated, serviced or stored. In order to highlight this consideration, the material which addresses safety is proceeded by the following signal words: Degree of Potential Signal Word...
Page 8: Serial Number Location
MODEL 1850 SERIAL NUMBER LOCATIONS TYPICAL CHIPPER SERIAL NUMBER AND/OR WORK ORDER NUMBER LOCATIONS . Beltshield NOTE: The engine information is located on the . Hinged chipper hood under handle engine block. The clutch information is . Top of throat located on the clutch plate.
Page 9: Safety Procedures
MODEL 1850 SAFETY PROCEDURES SAFETY PROCEDURES DANGER The words Danger, Warning, Caution, and DANGER Notice are used on the safety decals and throughout this manual, to make you aware of the safety Before starting the machine, take a minute to procedures.
Page 10 MODEL 1850 SAFETY PROCEDURES SAFETY PROCEDURES DANGER DANGER Never reach into the infeed hopper area of Always block the tires and the machine tongue the machine, there is never any reason to. The whenever the machine is unhooked for operation.
Page 11 MODEL 1850 SAFETY PROCEDURES SAFETY PROCEDURES DANGER DANGER Before attempting any type of maintenance DO NOT operate this machine indoors! Exhaust disengage clutch, install clutch lock if equipped, turn fumes can be fatal. Never refuel while the machine is off engine, wait for the chipper disc/drum to come running.
Page 12 MODEL 1850 SAFETY PROCEDURES SAFETY PROCEDURES WARNING DANGER The machine was built with a chipper hood engine Do not work on the machine if the engine is running with the clutch disengaged. A clutch can self engage if disable plug which disables the engine if it is not...
Page 13 MODEL 1850 SAFETY PROCEDURES SAFETY PROCEDURES WARNING WARNING Before you begin to transport your trailerized machine DO NOT operate this machine unless all hydraulic follow all of the transportation procedures on pages control devises operate properly. They must function, 34-36. Make sure that the tongue has been raised to shift and position smoothly and accurately at all times.
Page 14 MODEL 1850 SAFETY PROCEDURES SAFETY PROCEDURES IF MACHINE IS EQUIPPED WITH UNDERCARRIAGE TRACK Machines equipped with undercarriage tracks are shipped with a manual from the track manufacturer. Refer to it for service, operation, and safety information. WARNING Do not attempt to operate the track machine on an ascending or descending slope of more than 25° or 46% or a side slope of more than 17°...
Page 15: Equipment Specifications
Model 1850: Height: 9’ 4” (2.8 m), Length: 21’ 2” (6.5 m), Width: 7’ 5” (2.3 m) Dimension: Model 1850 w/ Loader: Height: 9’ 4” (2.8 m), Length: 24’ (7.3 m), Width: 8’ 5” (2.6 m) (Not Shown) Model 1850 Track: Height: 11’...
Page 16 MODEL 1850 DECALS DECAL LOCATIONS - MODEL 1850 Decal locations may vary, these are general locations. 9,13,14 1,15 4,7,18, 33,47 11,44 34,51 21,27 6,22,31,32 1,22 2,46 INSIDE CAB (If Equipped) 17,20,23,55,57,58 53,54, 56,59 40,43 1,15 3,10,50 22,24,26,29,30, 37,38,39,42 12,22 16,17,19,20,...
Page 17 MODEL 1850 DECALS DECAL LOCATIONS - MODEL 1850 Modifications and/or additions of decals to this list will happen. Consult chipper dealer or manufacturer for most current decal package. LOCATION NUMBER DESCRIPTION SPD-0 Moving Parts... SPD-03 Lockout All Energy Sources... SPD-0 Flying Discharge Material...
Page 18 MODEL 1850 DECALS DECAL LOCATIONS - MODEL 1850 Decal locations may vary, these are general locations. 9,13,14 1,15 4,7,18, 33,47 11,44 34,51 21,27 6,22,31,32 1,22 2,46 INSIDE CAB (If Equipped) 17,20,23,55,57,58 53,54, 56,59 40,43 1,15 3,10,50 22,24,26,29,30, 37,38,39,42 12,22 16,17,19,20,...
Page 19 MODEL 1850 DECALS DECAL LOCATIONS - MODEL 1850 Modifications and/or additions of decals to this list will happen. Consult chipper dealer or manufacturer for most current decal package. LOCATION NUMBER DESCRIPTION N-0 Maintain Lubrication... N-03 Service Required Under Beltshield... N-0 Frequently Adjust...PTO...
Page 20: Decals
MODEL 1850 DECALS DECALS Decals located on your Bandit equipment contain useful information to assist you in operating your equipment safely. Some of the decals on your machine and their location are shown in this section. It is very important that all decals remain in place and in good condition on your machine. Please follow the care and instructions given below: 1) You should use soap and water to keep your decals clean.
Page 21 MODEL 1850 DECALS Bandit Copyright 9/07 PAGE 9...
Page 22 MODEL 1850 DECALS Bandit Copyright 9/07 PAGE 0...
Page 23: Autofeed Options
MODEL 1850 AUTOFEED OPTIONS AUTOFEED OPTIONS AUTOFEED SYSTEM Consult the original manufacturer’s manual for your chippers Autofeed operating and maintenance procedures When processing material through the chipper, the feed system will automatically stop when the engine drops below a preset RPM point. The engine is constantly being monitored by an adjustable electronic speed switch.
Page 24 See Figure . Dual Coil Normally seen on bigger machines such as 280, 1850, 1890, 1990, 2090, etc. and special options. Reverse Valve This will normally be located on the infeed hopper of the machine. It can recognized by a valve with two solenoids bolted on a square block.
Page 25 MODEL 1850 AUTOFEED OPTIONS TROUBLE SHOOTING GUIDE PROBLEM POSSIBLE CAUSE SOLUTION No Display -Gauge not getting power. -Check continuity of Red wire to a clean power source. -Check 7.5 amp fuse. -Check connection at engine disable plug at hood pin.
Page 26 MODEL 1850 AUTOFEED OPTIONS TROUBLE SHOOTING GUIDE cont. PROBLEM POSSIBLE CAUSE SOLUTION Feedwheels Run -Backup time set wrong. Reset backup time. Normal setting is .3 seconds. In Reverse From -Sticking reverse valve. -Check solenoid operation. Normal -Override cartridge manually by sticking a small allen wrench in the end of the solenoid.
Page 27: Controls
MODEL 1850 CONTROLS CONTROLS CORRECT OPERATION OF FEED CONTROL HANDLE PULL TO REVERSE FEEDING FEEDING FOR ALL CHIPPERS DESIGNED TO BE “LOADER FED”. IF YOU ARE IN THE AREA OF INFEED HOPPER, ALWAYS BE PREPARED TO OPERATE AND WITHIN EASY REACH OF THE FEED CONTROL HANDLE.
Page 28 MODEL 1850 CONTROLS CONTROLS Model 1850 Basic Location of Controls and Adjustments LOCATION SHOWN NOT SHOWN 1. Foot Pad Jack Knives & Hardware 2. Hydraulic Tongue Jack Wooden Push Paddle . Autofeed Controls Feedwheel Motor Coupler 4. Engine Controls, Adjusters Loader “Optional”...
Page 29 MODEL 1850 CONTROLS CONTROL OPERATING PROCEDURES Feedwheel Control Bar: The feedwheel control bar operates the feedwheel(s). This machine is NOT designed or authorized to be hand fed! To make the feedwheel(s) operate so they are pulling material into the machine, push the control handle towards the machine.
Page 30 MODEL 1850 CONTROLS CONTROLS Basic Location Of Cab Controls And Adjustments For Model 1850 With A Cab 4. Road Side Stabilizer Control (if equipped) . Feedwheel Control Switch . Discharge Swivel Control 2. Joystick Console Adjustment Knob 6. Flipper Control 3.
Page 31 MODEL 1850 CONTROLS Joystick Application For The Loader Function Of Model 1850 MAIN BOOM DOWN LEFT RIGHT GRAPPLE SWING SWING ROTATE BOOM MAIN BOOM UP Right Hand Joystick Left Hand Joystick Joystick Switch: Grapple Joystick Switch: Yoke OPEN CLOSE DOWN...
Page 32 MODEL 1850 CONTROLS WINCH OPERATING PROCEDURES Figure Clutch Lock Pin (Safety Pin) (Pin does not need to be retracted this far, this is for visual reference only.) Figure Cable Feed Bottom Of Drum Clutch Handle WARNING HYDRAULIC WINCH OPERATION PER WINCH MANUFACTURER! Install 5/16”...
Page 33 MODEL 1850 CONTROLS CHIPPER HOOD ENGINE DISABLE PLUG OPERATION This chipper hood engine disable plug is installed Chipper Hood Engine for safety purposes. It is designed to shut down the Disable Plug engine if the hood pin is not properly in place holding the chipper hood in the closed position.
Page 34 MODEL 1850 CONTROLS SPRING LOCK FOR HOOD PIN OPERATION The patented spring lock for hood pin, is installed for safety purposes. It is designed to help keep the hood pin from being removed if the chipper disc is turning. NEVER ATTEMPT TO PUSH THE SPRING LOCK FOR HOOD PIN DOWN OR REMOVE THE HOOD PIN, UNTIL AFTER THE ENGINE AND CHIPPER DISC HAVE BOTH COME TO A COMPLETE STOP.
Page 35 MODEL 1850 CONTROLS CONSULT THE ENGINE MANUFACTURER’S MANUAL FOR SPECIFIC CONTROLS, OPERATION, & MAINTENANCE FOR TYPICAL ENGINES Ignition Switch: Turn the ignition switch key clockwise one stop (on position) to turn the electrical system on. The key should remain in the on position while the engine is running.
Page 36: Transportation Procedures
MODEL 1850 TRANSPORTATION PROCEDURES Transportation Procedures WARNING BEFORE TRANSPORTING THE MACHINE THE FOLLOWING MUST BE COMPLETED. Idle engine, disengage clutch, and install clutch lock if equipped. Make sure the feedwheel is in the lowered position. Place all hydraulic controls in the “off” position.
Page 37 MODEL 1850 TRANSPORTATION PROCEDURES Loader Transportation Procedures Figure Figure WARNING IF EQUIPPED WITH LOADER OPTION, BEFORE TRANSPORTING THE MACHINE THE FOLLOWING MUST BE COMPLETED ALONG WITH THE MACHINE TRANSPORTATION PROCEDURES. Idle engine, disengage clutch, and install clutch lock if equipped.
Page 38 MODEL 1850 TRANSPORTATION PROCEDURES Loading & Unloading Self-Propelled Machines WARNING BEFORE ATTEMPTING TO USE A TRAILER FOR TRANSPORT, MAKE SURE THE TRAILER TOWING VEHICLE IS APPROPRIATE FOR THE TASK. The trailer has a cargo weight rating capacity for the weight of the machine. The combined weight of the trailer and the machine can not exceed the load capacity of the tires, axles, hitch coupler system or the GVWR (Gross Vehicle Weight Rating) of the trailer.
Page 39 MODEL 1850 MAINTENANCE SECTION MAINTENANCE SECTION The Bandit is a very simple machine to maintain. If you will follow a regular scheduled preventative maintenance program you should have years of trouble free operation. DANGER Before attempting any type of maintenance disengage clutch, install clutch lock if equipped, turn off engine, wait for the disc/drum to come to a complete stop, install the disc/drum lock pin, disconnect battery, and make sure the ignition key is in your possession.
Page 40 MODEL 1850 MAINTENANCE SECTION DAILY START UP & MAINTENANCE (cont.) 7) Check chipper disc assembly: 13) Grease loader (if equipped): Check for elongated bolt holes, secure welds, torqued Grease all loader and grapple pins and bushings with bolts, excessive wear and impact cracks. If a problem to shots of an EP- Lithium type grease.
Page 41 MODEL 1850 MAINTENANCE SECTION DAILY START UP & MAINTENANCE (cont.) 22) Check radiator, debris screen: 27) Inspect axle dust caps (if equipped): Thoroughly clean radiator fins at least once a day and Inspect axle dust caps and replace if damaged or twice in excessive conditions.
Page 42 MODEL 1850 MAINTENANCE SECTION MONTHLY MAINTENANCE 1) Check towing hitch: 7) Check hydraulic function pressures: Check for excessive damage or wear. Replace if Check, reset and maintain all hydraulic function needed. Keep pintle ring greased to reduce wear. pressure settings to a maximum of the specified PSI (bar).
Page 43 MODEL 1850 MAINTENANCE SECTION MAINTENANCE SECTION BOLT TORQUE CHART (THESE TORQUES ARE BASED ON DRY, CLEAN THREADS) DESCRIPTION BOLT SIZE TORQUE (FT.-LBS.) TORQUE (Nm) Chipper Bearing Bolts /” - 0 NC Bearing Retainer Bolts ” - 8 NC Draw Ring Bolts /”...
Page 44 MODEL 1850 MAINTENANCE SECTION DAILY START UP & MAINTENANCE CHECK LIST Each day before starting your machine these checks must be made: O.K. Repaired Check the safety decals and engine gauges, replace if damaged. Check, maintain, and service all safety equipment for proper operation: engine disable plug, control bar, hood pin, spring lock for hood pin (disc chippers only), pusher tool, etc.
Page 45 MODEL 1850 MAINTENANCE SECTION WEEKLY CHECK LIST O.K. Repaired Check anvil clearance, tightness, and wear. Check alternator and fan belts on engine. Check spring tension on easy climb system. Check and retighten wheel lug nuts (if equipped). Check and retighten fuel tank and hydraulic tank mount bolts.
Page 46 MODEL 1850 MAINTENANCE SECTION BELT TENSION GENERAL RULES FOR TENSIONING 1. Check tensioning during the first 2 through 48 hours of run-in operation especially. . Over tensioning or under tensioning shortens belt and bearing life. . Keep belts free from foreign materials that may cause the belt to slip.
Page 47 MODEL 1850 MAINTENANCE SECTION BELT TENSION FIGURE 1 CHIPPER CLUTCH END SHEAVE OF ENGINE ENGINE CHECK SHEAVE MOUNTING BOLTS ALIGNMENT WITH STRAIGHT EDGE OR STRING RADIATOR END OF ENGINE ENGINE SHEAVE ENGINE ENGINE MOUNTING MOUNTING POSITIONING BOLTS BOLTS JAM NUTS...
Page 48 MODEL 1850 MAINTENANCE SECTION ANVIL ADJUSTMENT DANGER Hex Nut Before attempting any type of maintenance disengage clutch, install clutch lock if equipped, turn off engine, wait for the disc to come to a complete stop, install the disc lock pin, disconnect battery, and...
Page 49 MODEL 1850 MAINTENANCE SECTION EASY CLIMB FEED SYSTEM DANGER Before attempting any type of maintenance disengage clutch, turn off engine, wait for the disc/drum to come to a complete stop, install the disc/drum lock pin, disconnect battery, and make sure the ignition key is in your possession.
Page 50 MODEL 1850 MAINTENANCE SECTION PROPER PROCEDURE FOR INSTALLATION AND REMOVAL OF TAPERLOCK KEYLESS FEEDWHEEL COUPLERS AND FEEDWHEEL MOTORS Proper Equipment Needed: Feedwheel motor with straight shaft. Torque wrench Correct feedwheel shaft and coupler ass’y 7mm crow foot Emery cloth and/or a file...
Page 51 MODEL 1850 MAINTENANCE SECTION PROPER PROCEDURE FOR INSTALLATION OF LEE-TITE FEEDWHEEL COUPLERS AND FEEDWHEEL MOTORS Proper Equipment Needed: Feedwheel motor with straight shaft. Torque wrench 3/8” x 5/8” x 1 1/2” long key (special) 15/16” socket Part number: 955-1006-68 A degreaser agent Correct feedwheel shaft and coupler ass’y...
Page 52 MODEL 1850 MAINTENANCE SECTION SERVICING BEARING BLOCK Your machine maybe equipped with bearing block(s) and hydraulic pump(s) that are belt driven. The female splines in the bearing block need to be packed with an EP-2 Lithium type grease every six months. To do this, unbolt the hydraulic pump from the bearing block and slide the hydraulic pump out of the bearing block.
Page 53 MODEL 1850 MAINTENANCE SECTION SERVICING / CHANGING FEEDWHEEL BEARING (WITH THE GRIP TIGHT BEARING BEHIND FEEDWHEEL MOTOR) Your Bandit Chipper maybe equipped with a tapered lock style (Grip Tight) feedwheel bearing on the hydraulic motor side of the feedwheel and a conventional (set screw) style on the opposite side. With the Grip Tight bearing this gives a very positive locking system to the feedwheel shaft.
Page 54: Maintenance
MODEL 1850 MAINTENANCE SECTION MAINTENANCE PROCEDURE FOR UNPLUGGING YOUR CHIPPER If your chipper is plugging, it is usually caused by allowing the engine to drop below required R.P.M.’s. This can be resolved by simply shutting the feedwheel(s) off when the engine begins to lug down.
Page 55 MODEL 1850 MAINTENANCE SECTION PAINT CARE To help keep up the appearance of your Bandit Equipment and reduce the possibility of surface rust follow these steps: ) The machine should be washed on a regular basis with a non-abrasive mild detergent and then rinsed thoroughly.
Page 56 MODEL 1850 MAINTENANCE SECTION TIRE WEAR DIAGNOSTIC CHART Wear Pattern Cause Action Center Wear Over Inflation Adjust pressure to particular load per tire catalog Edge Wear Under Inflation Adjust pressure to particular load per tire catalog Side Wear Not Hauling Trailer Level...
Page 57: Hydraulic Section
MODEL 1850 HYDRAULIC SECTION HYDRAULIC SECTION WARNING DO NOT GO NEAR HYDRAULIC LEAKS! High pressure oil easily punctures skin causing serious injury, gangrene, or death. If injured, seek emergency medical help. Immediate surgery is required to remove oil. DO NOT use fingers or skin to check for leaks. Lower load or relieve hydraulic pressure before loosening fittings.
Page 58 MODEL 1850 HYDRAULIC SECTION HYDRAULIC SECTION Alternate hydraulic oils are available, but they do not equal the performance or longevity of the “Hydrex XV” oil. Consult the following information supplied by the oil distributor. CELCIUS - -8 + +7 FAHRENHEIT...
Page 59 MODEL 1850 HYDRAULIC SECTION TYPICAL HYDRAULIC RELIEF PRESSURE SETTINGS TYPICAL HYDRAULIC FLOWS AND RPM SETTINGS (Approximate, For Reference Only, Engine At Full RPM) Track (each) - GPM (LPM) 6.6 (00) Main Boom - GPM (LPM) 0 (8) Jib Boom, Grapple, Loader Swing - GPM (LPM)
Page 60 MODEL 1850 HYDRAULIC SECTION HYDRAULIC SECTION THE BANDIT HYDRAULIC SYSTEM The Bandit is equipped with a very efficient, simple • If the Bandit’s hydraulic system is kept clean and hydraulic system. Each component is capable of the hydraulic pressures are not increased beyond...
Page 61 Bottom Feedwheel Relief Autofeed Plus Block PROCEDURE FOR MODEL 1850 WARNING Before attempting any hydraulic pressure settings, make sure engine is shut off, engine key removed and in your possession, hydraulic oil is clean, hydraulic tank is 7/8 full, and the machine has been pre-run to warm the hydraulic oil.
Page 62 HYDRAULIC PRESSURE ADJUSTMENT PROCEDURE VALVE BANK TEST PORTS PROCEDURE FOR MODEL 1850 WITH LOADER OR TRACKS WARNING Before attempting any hydraulic pressure settings, make sure engine is shut off, engine key removed and in your possession, hydraulic oil is clean, hydraulic tank is 7/8 full, and the machine has been pre-run to warm the hydraulic oil.
Page 63 HYDRAULIC SECTION PROCEDURE FOR CHECKING OPTIONAL HYDRAULIC COMPONENTS FOR MODEL 1850 HYDRAULIC COMPONENT OPTIONS The relief valve is typically located internally in the control valve. Do not adjust this relief valve above the specified PSI (bar). The relief valve system is a simple spring tension design but small pieces of debris can stick the valve partially open which weakens the feedwheel power.
Page 64 FEEDWHEEL CONTROL VALVE WARNING MODEL 1850 PROCEDURE Before attempting any hydraulic pressure settings, make sure engine is shut off, the ignition key is removed and in your possession, hydraulic oil is clean, hydraulic tank is 7/8 full, and the machine has been pre-run to warm the hydraulic oil.
Page 65 MODEL 1850 HYDRAULIC SECTION HYDRAULIC SYSTEM TROUBLE SHOOTING Before attempting any type of maintenance disengage clutch, install clutch lock if equipped, turn off engine, wait for the disc/drum to come to a complete stop, install the disc/drum lock pin, disconnect battery, and make sure the ignition key is in your...
Page 66 MODEL 1850 HYDRAULIC SECTION CORRECTING HYDRAULIC PROBLEMS Before attempting any type of maintenance disengage clutch, install clutch lock if equipped, turn off engine, wait for the disc/drum to come to a complete stop, install the disc/drum lock pin, disconnect battery, and make sure the ignition key is in your...
Page 67 MODEL 1850 HYDRAULIC SECTION HYDRAULIC MOTOR CHECK OUT HYDRAULIC MOTOR CHECK OUT FOR MACHINES WITH LIVE HYDRAULICS To check out a hydraulic motor the mechanic will need a pressure gauge capable of reading 3000 p.s.i. (207 bar), a Tee fitting to install in the control valve, a plug fitting to install in the control valve and a clean 5 gallon (19L) pail.
Page 68 MODEL 1850 HYDRAULIC SECTION HYDRAULIC PUMP CHECK OUT HYDRAULIC PUMP CHECK OUT WITHOUT USING A FLOW METER To check out the hydraulic pump the mechanic will need a needle type flow control valve, a pressure gauge capable of reading 3000 psi (207 bar) and a long enough hose that will span between the pump and the hydraulic tank.
Page 69 MODEL 1850 HYDRAULIC SECTION HYDRAULIC PUMP CHECK OUT HYDRAULIC PUMP CHECK OUT USING A FLOW METER To check out the hydraulic pump the mechanic will need a needle type flow meter capable of reading 3000 psi (207 bar) and a long enough hose that will go from the flow meter back to the first component.
Page 70 MODEL 1850 HYDRAULIC SECTION CONTROL VALVE DETENT ASSEMBLY AND O-RING REPLACEMENT Tools Required: - Small amount of clean hydraulic oil - Clean working area, free of debris and shop rags 1/2” Drag Link - 3/16” Tee handle hex driver Drive Socket - 1/2”...
Page 71 MODEL 1850 HYDRAULIC SECTION 1850 SPECIFIC SCHEMATIC FUNCTION MAY VARY DEPENDING ON OPTIONS OR COMPONENT MANUFACTURE. WITH OPTIONAL REAR STABILIZERS CONTROL VALVE CHECK VALVE DISCHARGE TONGUE JACK MOTOR CYLINDER FLIPPER CHECK CYLINDER VALVE BOTTOM FEEDWHEEL FEEDWHEEL MOTOR MOTOR AUTOFEED AUTOFEED...
Page 72 MODEL 1850 HYDRAULIC SECTION 1850 With Loader SPECIFIC SCHEMATIC FUNCTION MAY VARY DEPENDING ON OPTIONS OR COMPONENT MANUFACTURE. WITH MODEL 1700 LOADER & OPTIONAL REAR STABILIZERS Bandit Copyright 9/07 PAGE 70...
Page 73 MODEL 1850 HYDRAULIC SECTION 1850 Track SPECIFIC SCHEMATIC FUNCTION MAY VARY DEPENDING ON OPTIONS OR COMPONENT MANUFACTURE. Bandit Copyright 9/07 PAGE 7...
Page 74: Chipper Section
MODEL 1850 CHIPPER SECTION CHIPPER SECTION Knives should be replaced in sets. These sets UNDER NO SITUATION IS HEAL OF KNIFE TO BE are determined by the amount of resharpening INSIDE EDGE OF MILLED POCKET! done to the knives. It should be reinstalled with another knife of comparable usage.
Page 75 MODEL 1850 CHIPPER SECTION KNIFE GRINDING AND FILING Only Bandit knives and hardware are recommended for use in your Bandit chippers. Only then can you be assured of a quality product that fits and performs the best to the standards of excellence that is expected from the Bandit chipper.
Page 76 MODEL 1850 CHIPPER SECTION KNIFE CHANGING PROCEDURE Only Bandit knives and hardware are recommended for use in your Bandit chippers. Only then can you be assured of a quality product that fits and performs the best to the standards of excellence that is expected from the Bandit chipper.
Page 77: Lubrication & Coolant
MODEL 1850 LUBRICATION & COOLANT LUBRICATION & COOLANT Engine: Follow original equipment manufacturer’s requirements for both changing oils and filters, refer to engine manual specifications. Engine Coolant: Refer to engine manufacturer’s manual specifications. Clutch: Follow original equipment manufacturer’s requirements for both greasing and adjusting. Frequently, adjust and lubricate per PTO manufacturer’s manual.
Page 78 MODEL 1850 ELECTRICAL SECTION 1850 WITH RADIO REMOTE MACHINE HARNESS 900-2912-36 SPECIFIC SCHEMATIC FUNCTION MAY VARY DEPENDING ON OPTIONS OR COMPONENT MANUFACTURE. Bandit Copyright 9/07 PAGE 76...
Page 79 MODEL 1850 ELECTRICAL SECTION 1850 WITH RADIO REMOTE MACHINE HARNESS TO VALVES SPECIFIC SCHEMATIC FUNCTION MAY VARY DEPENDING ON OPTIONS OR COMPONENT MANUFACTURE. Bandit Copyright 9/07 PAGE 77...
Page 80 MODEL 1850 ELECTRICAL SECTION RADIO REMOTE 1850 WITH JOHN DEERE ENGINE MACHINE HARNESS TO ENGINE 999-800051 SPECIFIC SCHEMATIC FUNCTION MAY VARY DEPENDING ON OPTIONS OR COMPONENT MANUFACTURE. Bandit Copyright 9/07 PAGE 78...
Page 81 MODEL 1850 ELECTRICAL SECTION RADIO REMOTE 1850 WITH CAT OR PERKINS ENGINE MACHINE HARNESS TO ENGINE 999-800018 SPECIFIC SCHEMATIC FUNCTION MAY VARY DEPENDING ON OPTIONS OR COMPONENT MANUFACTURE. Bandit Copyright 9/07 PAGE 79...
Page 82 MODEL 1850 ELECTRICAL SECTION 1850 WITH RADIO REMOTE TETHER 900-2912-82 SPECIFIC SCHEMATIC FUNCTION MAY VARY DEPENDING ON OPTIONS OR COMPONENT MANUFACTURE. Bandit Copyright 9/07 PAGE 80...
Page 83 MODEL 1850 ELECTRICAL SECTION 1850 WITH RADIO REMOTE RECIEVER, TRANSMITTER, & OUTPUT SPECIFIC SCHEMATIC FUNCTION MAY VARY DEPENDING ON OPTIONS OR COMPONENT MANUFACTURE. Bandit Copyright 9/07 PAGE 8...
Page 84: Electrical Section
MODEL 1850 ELECTRICAL SECTION TYPICAL ELECTRICAL WIRING DIAGRAMS WIRING FOR STANDARD 6 PRONG PLUG AND 6 WIRE MAIN CABLE EFFECTIVE ON MACHINES BUILT AFTER 11/01/04 POWER TO 6 Wire Main Cable Color Code BREAK AWAY BREAKAWAY- SWITCH BLACK WIRE Red R (Brakes & Breakaway Switch)
Page 85: Replacement Parts Section
MODEL 1850 REPLACEMENT PARTS REPLACEMENT PARTS SECTION Depending on what replacement parts you are ordering the following information will be needed: ENGINE COMPONENTS CLUTCH COMPONENTS CHIPPER COMPONENTS Brand Brand Serial Number Engine Serial Number Serial Number Model Number of Chipper Engine Spec.
Page 86 MODEL 1850 INFEED HOPPER COMPONENTS LEE-TITE COUPLER (PRE 5/07) Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07 PAGE 8...
Page 87: Infeed Hopper Components
MODEL 1850 INFEED HOPPER COMPONENTS STANDARD SUPER SIZED LOCATION PART NUMBER PART NUMBER DESCRIPTION 9-00- 9-00- Weld On Pan For Infeed Hopper 980-0069 980-0069 Mount For LED Light Bar 900-909-9 900-909-9 LED Light Bar 9-06-9 9-06-9 Pivot Pin...
Page 88 MODEL 1850 INFEED HOPPER COMPONENTS LEE-TITE COUPLER (PRE 5/07) Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07 PAGE 86...
Page 89 MODEL 1850 INFEED HOPPER COMPONENTS STANDARD SUPER SIZED LOCATION PART NUMBER PART NUMBER DESCRIPTION 33 a. 955-0502-03 955-0502-38 Top Yoke Assembly (Start 2/03) 955-0500-12 955-0502-16 Top Yoke Assembly (Pre 2/03) 900-906-9 900-906-9 Top Feedwheel Hydraulic Motor 955-1007-72 955-1007-72 Yoke Lock Pin...
Page 90 MODEL 1850 CONVEYOR COMPONENTS DRIVE SET UP (PRE 5/07) Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07 PAGE 88...
Page 91: Conveyor Components
MODEL 1850 CONVEYOR COMPONENTS STANDARD SUPER SIZED LOCATION PART NUMBER PART NUMBER DESCRIPTION 900-906- 900-906- Infeed Conveyor Tail Shaft Bearing 9-00-6 9-00-6 Infeed Conveyor Tail Shaft Assembly 3 a. 900-4902-75 900-4902-75 Adjuster Bolt - 5/8”-11NC x 6” (Start 6/07) 900-4910-43 900-4910-43 3/4”-10NC x 8”...
Page 92 MODEL 1850 CHIPPER COMPONENTS Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07 PAGE 90...
Page 93: Chipper Components
MODEL 1850 CHIPPER COMPONENTS LOCATION PART NUMBER DESCRIPTION 9-00-6 Front Chipper Bearing Cover 2 a. 900-4912-45 Bearing Retainer Bolt - 1”-8NC x 3 3/4” Hex Head (Start 6/05) 900-4909-12 Bearing Retainer Bolt - 1”-8NC x 3” Hex Head (5/02 - 6/05) 900-4907-14 Bearing Retainer Bolt - 3/4”-10NC x 3”...
Page 94 MODEL 1850 CHIPPER COMPONENTS Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07 PAGE 9...
Page 95 MODEL 1850 CHIPPER COMPONENTS LOCATION PART NUMBER DESCRIPTION 7 a. 9-00098 Beltshield Assembly - Chipper End (Start /0) 9-000- Beltshield Assembly - Piece (Not Shown) (Pre /0) 9-00099 Beltshield Assembly - PTO End (Start /0) 9-00 Beltshield Bottom - Chipper End (Start /0)
Page 96: Chipper Knife & Hardware
MODEL 1850 CHIPPER KNIFE & HARDWARE KNIFE BOLTS MUST BE INSTALLED THROUGH KNIFE AS SHOWN Part Numbers For Model 1850 Knives LOCATION PART NUMBER DESCRIPTION 900-9901-18 1/2” x 4 1/2” x 7 1/4” Chipper Knife 900-9901-19 1/2” x 4 1/2” x 5 1/8” Chipper Knife 900-4903-92 5/8”-11NC x 3”...
Page 97: Anvil & Hardware
MODEL 1850 ANVIL & HARDWARE LOCATION PART NUMBER DESCRIPTION 9-000-7 Anvil Only 9-07- “AR” Anvil Only 914-1002-14 Square Anvil Washer - 1/4” Thick 900-4902-87 5/16”-18NC x 3/4” Set Screw 900-4902-75 Anvil Eye Bolt - 5/8”-11NC x 6” 900-4900-33 3/4” High Collar Lock Washer 900-4902-78 3/4”-10NC x 2 1/2”...
Page 98: Discharge Components
MODEL 1850 DISCHARGE COMPONENTS DISCHARGE PRIOR STYLE LOCATION PART NUMBER DESCRIPTION a. 900-9-7 Discharge Swivel Hydraulic Motor - SAE O-ring 900-90- Discharge Swivel Hydraulic Motor - Pipe Fitting 980-00-66 Hydraulic Swivel Mount 9-006-7 Hydraulic Swivel Motor Mount 980-06-0 Chain Guard Mount...
Page 99 MODEL 1850 DISCHARGE COMPONENTS HAND CRANK ADJ. HEIGHT DISCHARGE LOCATION PART NUMBER DESCRIPTION 980-300032 Hand Crank Adj. Height Mount Brackets 2 a. 980-0510-86 Hand Crank For Adj. Height Discharge - Mounted On The Side 980-0508-51 Hand Crank For Adj. Height Discharge - Mounted Underneath...
Page 100 MODEL 1850 HYDRAULIC COMPONENTS TYPICAL MODEL 1850 HYDRAULIC SCHEMATIC (Options May Vary) PIPE FITTING JIC / SAE O-RING Examples of straight fittings. Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07 PAGE 98...
Page 101: Hydraulic Components
MODEL 1850 HYDRAULIC COMPONENTS TYPICAL MODEL 1850 HYDRAULIC COMPONENTS (Options May Vary) LOCATION PIPE FITTING SAE O-RING DESCRIPTION See Pages 126-127 See Pages 126-127 Hydraulic Tank 900-3912-51 Hydraulic Tank Strainer - 2” 900-3920-14 Shut Off Valve - 1 1/2” a.
Page 102 MODEL 1850 HYDRAULIC COMPONENTS TYPICAL MODEL 1850 WITH LOADER HYDRAULIC SCHEMATIC (Options May Vary) PIPE FITTING JIC / SAE O-RING Examples of straight fittings. Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07 PAGE 00...
Page 103 MODEL 1850 HYDRAULIC COMPONENTS TYPICAL MODEL 1850 WITH LOADER HYDRAULIC COMPONENTS (Options May Vary) LOCATION PIPE FITTING SAE O-RING DESCRIPTION See Pages 126-127 See Pages 126-127 Hydraulic Tank 900-3912-51 900-3912-51 Hydraulic Tank Strainer - 2” 900-3920-14 900-3920-14 Shut Off Valve - 1 1/2”...
Page 104 MODEL 1850 HYDRAULIC COMPONENTS TYPICAL MODEL 1850 WITH LOADER HYDRAULIC SCHEMATIC (Options May Vary) PIPE FITTING JIC / SAE O-RING Examples of straight fittings. Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07 PAGE 0...
Page 105 MODEL 1850 HYDRAULIC COMPONENTS TYPICAL MODEL 1850 WITH LOADER HYDRAULIC COMPONENTS (Options May Vary) LOCATION PIPE FITTING SAE O-RING DESCRIPTION 6 a. 900-90-7 Swing Motor (Start /98) 900-90-0 Swing Cylinder (Pre /98) - (Not Shown) 900-90-70 Cross Over Relief 8 a.
Page 106 MODEL 1850 HYDRAULIC COMPONENTS TYPICAL MODEL 1850 TRACK HYDRAULIC SCHEMATIC (Options May Vary) PIPE FITTING JIC / SAE O-RING Examples of straight fittings. Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07 PAGE 0...
Page 107 MODEL 1850 HYDRAULIC COMPONENTS TYPICAL MODEL 1850 TRACK HYDRAULIC COMPONENTS (Options May Vary) LOCATION PIPE FITTING SAE O-RING DESCRIPTION See Pages 126-127 See Pages 126-127 Hydraulic Tank a. 900-90-8 Filter Head 900-90-66 Filter Element 900-90-7 Filter Gauge 900-3905-57 Shut Off Valve - 3/4”...
Page 108 MODEL 1850 HYDRAULIC COMPONENTS TYPICAL MODEL 1850 TRACK HYDRAULIC SCHEMATIC (Options May Vary) PIPE FITTING JIC / SAE O-RING Examples of straight fittings. Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07 PAGE 06...
Page 109 MODEL 1850 HYDRAULIC COMPONENTS TYPICAL MODEL 1850 TRACK (cont.) HYDRAULIC COMPONENTS (Options May Vary) LOCATION PIPE FITTING SAE O-RING DESCRIPTION 900-90-70 Cross Over Relief a. 900-90-7 Swing Motor (Start /98) 900-90-0 Swing Cylinder (Pre /98) - (Not Shown) a.
Page 110 MODEL 1850 HYDRAULIC COMPONENTS RELIEF BLOCK Hydraulic Hose From Pump Hydraulic Hose To Tank Torque Autofeed Cartridge Nut to a Maximum of 4 to 6 ft.-lbs. (5 to 8 Nm) and Install Loc-Tite 241. Over Torque Will Cause Damage and Will Also Void Warranty.
Page 111 MODEL 1850 HYDRAULIC COMPONENTS RELIEF BLOCK LOCATION PIPE FITTING SAE O-RING DESCRIPTION 1 a. 900-2900-82 Autofeed Block Only Main Relief Block Only 900-9-7 900-9-7 Autofeed Cartridge Only 900-3923-44 900-3923-44 12 V Autofeed Solenoid Only 4 a. 900-3908-23 900-3908-23 Main Relief Only (Vickers)
Page 112 MODEL 1850 HYDRAULIC COMPONENTS TYPICAL SPRING LOADED CONTROL VALVE TYPICAL FEEDWHEEL CONTROL VALVES 4,12 1,12 3,12 Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07 PAGE 0...
Page 113 MODEL 1850 HYDRAULIC COMPONENTS TYPICAL SPRING LOADED CONTROL VALVE COMPONENTS LOCATION PART NUMBER DESCRIPTION 90-000-9 Handle Only (Long) 900-3905-95 Valve Bracket Only With Screws 904-0003-30 Master Link Only Control Valve 904-0003-31 Pin And Cotter Key For Control Valve 904-0003-32 Bracket, Handle And Chain Link NOTE: INCLUDES #’s 1, 2, 3, 4...
Page 114 MODEL 1850 HYDRAULIC COMPONENTS Dual Control Valve 900-3916-62 LOCATION PART NUMBER DESCRIPTION 900-9-70 Seal Kit (Includes through 8) LOCATION PART NUMBER DESCRIPTION 900-97-7 Handle Kit (Includes through 8) Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07...
Page 115 MODEL 1850 HYDRAULIC COMPONENTS Parker Valve Section LOCATION PART NUMBER DESCRIPTION Valve Section 900-98-9 Pressure Limiter a. 900-98-0 Spool - Closed Center 900-98- Spool - Open Center 4 a. 900-3938-71 Electrohydraulic Pilot - 12V 900-3938-72 Electrohydraulic Pilot - 24V...
Page 116 MODEL 1850 HYDRAULIC COMPONENTS Husco Valve Section LOCATION PART NUMBER DESCRIPTION 900-3938-46 Solenoid Only - 12 Volt Pilot Port 90-000-8 Handle Kit 900-3917-80 Main Relief - (3000 PSI Max.) 5 a. 900-3917-79 Low Pressure Port Relief - (1000 PSI Max.) 900-3917-80 High Pressure Port Relief - (3000 PSI Max.)
Page 117 MODEL 1850 HYDRAULIC COMPONENTS FPS Valve LOCATION PART NUMBER DESCRIPTION 1 a. 900-3938-12 Solenoid Only - 12 Volt 900-3938-13 Solenoid Only - 24 Volt 900-908- Relief Only Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07 PAGE ...
Page 118 MODEL 1850 HYDRAULIC COMPONENTS Kawasaki Joystick LOCATION PART NUMBER DESCRIPTION 900-98- Handle With Switches 900-98-8 Bellows 900-3938-55 Joystick Lever (Not Shown) 4 a. 900-3938-56 Spring Used With Parker Valve Bank (Not Shown) 900-3938-57 Spring Used With Husco Valve Bank (Not Shown) 5 a.
Page 119 MODEL 1850 HYDRAULIC COMPONENTS Hydro Control Joystick LOCATION PART NUMBER DESCRIPTION 900-90-80 Switch Boot For Top Of Handle 900-9-8 Handle Assembly a. 900-9- /” Spade Snap Action Switch (Not Shown) 900-9-8 /6” Spade Snap Action Switch (Not Shown) Joystick Assembly Bandit NOTE: Parts may not be exactly as shown.
Page 120 MODEL 1850 HYDRAULIC COMPONENTS Control Arms & Valve Linkages Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07 PAGE 8...
Page 121 980-0125-74 Single Valve Linkage 955-200092 Double Valve Linkage 5 a. 955-1010-17 Control Valve Linkage With Handle - 1850 With Loader 900-9904-59 Vinyl Cap For Control Valve Linkage Handle 955-1011-32 Hydraulic Control Arm - 1850 Track 955-200101 Double Control Valve Linkage Assembly (Side By Side Valves)
Page 122 MODEL 1850 HYDRAULIC COMPONENTS HYDRAULIC FILTERS - REFERENCE ONLY (REFER TO CHECK SHEET FOR PART NUMBERS) LOCATION PART NUMBER DESCRIPTION 900-9-9 Internal Hydraulic Return Filter Assembly (Includes Filter Element) 900-9- Filter Element Only For Internal Return Hydraulic Filter Assembly 900-3910-18...
Page 123 MODEL 1850 HYDRAULIC COMPONENTS LOADER & TRACK PUMP DRIVES LOCATION PART NUMBER DESCRIPTION Stub Shaft For Engine Pump Belt 900-3913-31 Pump Bearing Block 900-90-7 Pump Belt Tension Adjuster 9-00- Pump Mount Plate 9-00-9 Pump Mount Slide 9-0- Sheave Guard Mount...
Page 124 MODEL 1850 FRAME & ACCESSORY COMPONENTS Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07 PAGE ...
Page 125: Frame & Accessory Components
MODEL 1850 FRAME & ACCESSORY COMPONENTS LOCATION PART NUMBER DESCRIPTION a. 900-900- /” Heavy Duty Pintle Ring Hitch 900-90-7 ” Heavy Duty Pintle Ring Hitch *--* Other Hitch Options Available a. 900-9-6 Coil Cable Assembly With 6 Prong Plugs - ’...
Page 126 MODEL 1850 FRAME & ACCESSORY COMPONENTS Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07 PAGE ...
Page 127 MODEL 1850 FRAME & ACCESSORY COMPONENTS LOCATION PART NUMBER DESCRIPTION 980-0006 Trailer Plug Receptacle Mount 980-0- Safety Chain Holder 22 a. 900-4912-71 Safety Chain W / Hooks and Spring Latches for Standard Tongue 900-4905-77 Hook For Safety Chain Engine Rails 900-4905-11 Engine Adjuster Rod End - 5/8”-11NC X 6”...
Page 128 MODEL 1850 FUEL & HYDRAULIC TANK COMPONENTS Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07 PAGE 6...
Page 129 Rubber Fuel Tank Pad (Not Shown) 955-0501-12 125 Gallon Rectangle Fuel Tank Assembly - 1850 Track 13 a. 900-2902-26 Electric Sight Gauge For 100 Gallon Rectangle Fuel Tank - 1850 Track 900-9-0 Electric Gauge Face 955-0501-60 70 Gallon Triangle Hydraulic Tank Assembly - 1850 Track 15 a.
Page 130 MODEL 1850 LOADER COMPONENTS MODEL 1700 LOADER (START 5/98) Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07 PAGE 8...
Page 131: Loader Components
MODEL 1850 LOADER COMPONENTS MODEL 1700 LOADER (START 5/98) LOCATION PART NUMBER DESCRIPTION 900-90-7 Loader Swing Hydraulic Motor 900-90-9 Input Shaft (Spline Adaptor) 900-90-8 Planetary Speed Reducer 900-9-8 Oil Hose For Planetary Speed Reducer 900-90- Oil Cup For Planetary Speed Reducer...
Page 132 MODEL 1850 LOADER COMPONENTS BACK HOE LOADER (PRE 5/98) Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07 PAGE 0...
Page 133 MODEL 1850 LOADER COMPONENTS BACK HOE LOADER (PRE 5/98) LOCATION PART NUMBER DESCRIPTION 9-000- Loader Pedestal Assembly 9-00-7 Cylinder Pin Nut 955-1008-64 Cylinder Pin Lock 9-0- Pivot Bushing Assembly 9-000- Pedestal Assembly 9-00-8 Main Boom To Pedestal Pin 9-000- Main Boom Assembly...
Page 134 MODEL 1850 LOADER COMPONENTS PLANETARY SPEED REDUCER Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07 PAGE ...
Page 135 MODEL 1850 LOADER COMPONENTS PLANETARY SPEED REDUCER LOCATION PART NUMBER DESCRIPTION Cap Screw 06 Shaft Seal* 06 Seal Carrier 15105 Backup Ring* 0 Quad Ring* O-Ring* Output Shaft 0 .” Straight Keyed 0 .” Tapered 096 6T 8/6 Spline...
Page 136 MODEL 1850 LOADER COMPONENTS DUAL CYLINDER GRAPPLE LOCATION PART NUMBER DESCRIPTION 9-00- Grapple Jaw Pin 9-00- Narrow Jaw Assembly 9-000-89 Grapple Cylinder Pins 9-00- Grapple Jaw Pin 9-00- Wide Jaw Assembly 9-0-67 Cylinder Cover Wide Jaw 900-90-70 Grapple Jaw Pin Nut 8 a.
Page 137 MODEL 1850 LOADER COMPONENTS SINGLE CYLINDER GRAPPLE LOCATION PART NUMBER DESCRIPTION 955-300043 Pivot Link Pin - 2” Diameter x 6 15/16” 955-200026 Pivot Link Assembly 955-300042 Pivot Link Pin - 2” Diameter x 9 1/2” 9-0007 Cylinder Assembly 900-4913-18 7/8”-9NC x 2 1/4” Hex Head Bolt 900-90-98 7/8”...
Page 138 MODEL 1850 LOADER COMPONENTS GRAPPLE ROTATOR Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07 PAGE 6...
Page 139 MODEL 1850 LOADER COMPONENTS GRAPPLE ROTATOR LOCATION PART NUMBER DESCRIPTION 1 a. 5002-508 Stator Plate, Upper (Pre 9/02) 5002-603 Stator Plate, Upper (Start 9/02) 00-8 Plug 0-0 O-Ring 00- Ball 00-6 Spring 0-08 Glide Ring 00- Rotator Shaft 006-00 Spring...
Page 140 MODEL 1850 LOADER COMPONENTS DUAL SWING BRAKE (START 9/02) Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07 PAGE 8...
Page 141 MODEL 1850 LOADER COMPONENTS DUAL SWING BRAKE (START 9/02) LOCATION PART NUMBER DESCRIPTION 006-7 Dual Swing Damper Body 900-908-8 Pin - mm Diameter 00-8 Grease Nipple 900-908- Washer 900-908-0 006-670 Bushing - mm Diameter 5016-274 Lower Brake Disc 5016-125 Brake Block...
Page 142 MODEL 1850 LOADER COMPONENTS KNUCKLE SWING BRAKE (PRE 9/02) LOCATION PART NUMBER DESCRIPTION 900-4904-80 Damper Link Body 00-6 00-9 Nut (M) 1017-839 Screw (M16 x 30) 900-4904-83 Brake Lining With Disc (2 Required Per Assembly) 900-90-8 Cup Spring 00-7 Washer 900-4904-81 Pivot Kit With Brake (Includes 2 - 7) (2 Required Per Ass’y)
Page 143: Remote Control Components
MODEL 1850 REMOTE CONTROL COMPONENTS OMNEX REMOTE LOR REMOTE LOCATION PART NUMBER DESCRIPTION 900-2917-09 Omnex Radio Transmitter - Trailerized Unit 900-2917-08 Omnex Radio Receiver - Trailerized Unit 900-2917-56 Omnex Radio Remote Kit - Trailerized Unit (Includes 1-2) 900-2912-81 LOR Radio Transmitter - Trailerized Unit...
Page 144 MODEL 1850 CAB COMPONENTS LEVER STYLE CONTROLS Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07 PAGE ...
Page 145: Cab Components
MODEL 1850 CAB COMPONENTS LOCATION PART NUMBER DESCRIPTION a. 960-000-98 Cab Door Window - Loader 900-8900-01 Cab Door Window - Track a. 960-000-7 Cab Door Assembly - Loader 900-9906-60 Cab Door Assembly - Track a. 900-9900-9 Outside Door Handle...
Page 146 MODEL 1850 CAB COMPONENTS LEVER STYLE CONTROLS Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07 PAGE ...
Page 147 MODEL 1850 CAB COMPONENTS LOCATION PART NUMBER DESCRIPTION a. 9-00-0 Gauge Panel 900-2904-77 Visual Flashing Alarm Indicator - 12 Volt (Not Shown) 900-2905-10 Visual Flashing Alarm Indicator - 24 Volt (Not Shown) 900-90-78 Audible Alarm Indicator (Not Shown) 900-96-...
Page 148 MODEL 1850 OPTIONAL COMPONENTS Bandit NOTE: Parts may not be exactly as shown. Copyright 9/07 PAGE 6...
Page 149: Optional Components
MODEL 1850 OPTIONAL COMPONENTS LOCATION PART NUMBER DESCRIPTION 900-9-7 Winch Hydraulic Motor (SAE O-rings) “RS” - Square 900-90- Winch Hydraulic Motor (Pipe Fittings) “RS” - Square 900-9-9 Winch Hydraulic Motor (SAE O-rings) “RE” - Round 98-00-0 Winch Motor Torque Arm For “RS” Motor 9-0-7 Winch Motor Torque Arm For “RE”...
Page 150 MODEL 1850 OPTIONAL COMPONENTS LOCATION PART NUMBER DESCRIPTION 900-3934-24 Tongue Jack Cylinder - Welded 900-3912-12 Tongue Jack Cylinder - Tie Rod 90-0007- Pin For Welded Cylinder (Not Shown) 914-1000-38 Lock Pin 980-0-0 Inside Tube Assembly 980-009- Drop Leg Foot Pad Assembly...
Page 151 MODEL 1850 OPTIONAL COMPONENTS LOCATION PART NUMBER DESCRIPTION 980-008-7 Bandit H.D. Foldaway Radiator Screen Ass’y (specify latch type) 980-0122-86 Spring Lock Tab Foldaway Radiator Screen Mount Tray For Foldaway Radiator Screen 900-7900-7 Weather Strip 900-4901-83 Spring Lock Plunger 900-7900-93 Rubber Cap For Spring Lock - 1/2” Diameter...
Page 152: Service Record
MODEL 1850 SERVICE RECORD SERVICE RECORD DATE DESCRIPTION AMOUNT Bandit Copyright 9/07 PAGE 0...

Brush Bandit 1850 Operating & Parts Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Brush Bandit 1850

Summary of Contents for Brush Bandit 1850

Table of Contents