Kioti Daedong License Plate Installation Instructions

INSTALLATION
INSTRUCTIONS
FOR UTV
LICENSE PLATE
1. PACkINg LIST
2. gENERAL SAFETy INFORmATION
3. ExPLOdEd VIEw
4. INSTALLATION INSTRUCTION
d.d kIT#. U3210-91152
kIOTI TRACTOR dIVISION /dAEdONg-USA, INC.
6300 Kioti Dr. Wendell, NC 27591
Toll Free:1-877-gO-kIOTI
Tel:1-919-374-5100 Fax:1-919-374-5001
http://www.kiotitractor.com
OVERSEAS SERVICE dIVISION / dAEdONg INdUSTRIAL Co.,Ltd.
1-12, BUKRI, NONGONG, DALSUNG-GUN, DAEGU, KOREA
Tel:82-53-610-3350 Fax:82-53-610-3359
http://www.daedong.co.kr
Printed in Korea. Sep.2009
MEC2200(UD120)-번호판조합-영문.indd 1
1. PACkINg LIST
NO. Part No. description
1 02761-50040B FLANGE NUT
2 02763-50080B FLANGE NUT
3 03024-50414B SCREW, WASHER
4 T2185-82561 BAND, CORD
5 T2611-75712 NUMBER PLATE ASSEMBLY
6 T4815-93211 NUT
7 U3210-91162 NUMBER BOARD SUPPORT PLATE
8 U3215-60191 WIRE HARNESS, PLATE LAMP
9 U3215-97782 BOLT, U TYPE (M8)
3. ExPLOdEd VIEw
(1) FLANGE NUT
(2) FLANGE NUT
(3) SCREW, WASHER
(4) BAND, CORD
(5) NUMBER PLATE ASSEMBLY
(6) NUT
(7) NUMBER BOARD SUPPORT PLATE
(8) WIRE HARNESS, PLATE LAMP
(9) BOLT
2. gENERAL SAFETy INFORmATION.
Q'Ty Remark
2
4
BEFORE SERVICINg ANd REPAIRINg
2
1. Read all safety instruction in this
5
manual and be aware of safety decal
1
locations on your machine.
6
2. Thoroughly clean your work area and
1 the machine.
1 3. Make sure the machine is on firm
and level ground and that the parking
2
brake is set.
4. Lower the implement to the ground.
5. Stop the engine and remove the key.
6. Disconnect the negative battery cable.
7. Place a "DO NOT OPERATE" tag in
the operator station.
wORkINg SAFETy
1. Do not operate or service the machine
while under the influence of alcohol,
medications, or other sustances.
2. Never wear loose fitting clothing and
always use safety equipment appro-
priate to the job.
4. INSTALLATION INSTRUCTION
1. Park the vehicle on firm and level ground. Then, engage the parking brake and stop
the engine.
5
9
9
3
2. Fit the U-bolts (9) to the left side of
8
1
7
the rear upper frame of the ROPS as
shown in the figure.
2
6
4
UT2S401A
This symbol means ATTENTION! yOUR SATETy IS INVOLVEd.
The message that follows the symbol contains important information
about satety. Carefully read the message.
3. Never use improvised tools, parts or
procedures. Use only recommended
tools appropriate to the work.
4. Extra care should be taken to work
safely when servicing is done by two
or more persons.
5. Always support the machine with safe-
ty stands rated for the weight of the
machine. Never work under a machine
that is supported solely with a jack.
6. Do not touch any rotating or hot parts
while the engine is running.
7. Escaping fluid (hydraulic oil) under pres-
sure can penetrate the skin causing seri-
ous injury. Relieve pressure before dis-
connecting hydraulic or fuel lines. Tighten
all connections before applying pressure.
dISPOSE OF FLUIdS PROPERLy
1. Observe relevant environmental protec-
tion regulations when disposing of oil.
NEVER pour fluids onto the ground,
down a drain, or into any body of water.
UUVS701B.
3. Remove the license plate lamp lens
and pass the wiring through the hole
of the license plate bracket. Then,
fix the license plate lamp (5) with the
screw (3) and nut (1) and install the
removed lens.
UT2S402A
UT2S403A
Next page▼
2014-09-30 오전 10:24:55