Table of Contents
Advertisement
Quick Links
The oil/water coolers type PHE are plate heat exchangers with soldered stainless steel plates.
Table of contents
1
2
2.1
2.2
2.3
2.4
3
3.1
3.2
4
4.1
4.2
4.3
4.4
5
6
7
8
Please observe protection
note ISO 16016.
Oil/water cooler PHE
(Plate heat exchanger)
Operating/Assembly instructions
Oil/water cooler - Type PHE
Drawn:
2020-02-07 Pz/Bet
Verified:
2020-03-03 Pz
KTR-N
Sheet:
Edition:
Replacing:
KTR-N dated 2017-08-16
Replaced by:
41412 EN
1 of 7
2
2
3
3
3
3
4
4
4
4
5
5
6
6
6
6
7
7
7
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for KTR-Group PHE Series
Summary of Contents for KTR-Group PHE Series
- Page 1 Oil/water cooler PHE KTR-N 41412 EN (Plate heat exchanger) Sheet: 1 of 7 Operating/Assembly instructions Edition: Oil/water cooler - Type PHE The oil/water coolers type PHE are plate heat exchangers with soldered stainless steel plates. Table of contents Technical data Advice General advice Safety and advice symbols...
- Page 2 Oil/water cooler PHE KTR-N 41412 EN (Plate heat exchanger) Sheet: 2 of 7 Operating/Assembly instructions Edition: Technical data Illustration 1: Oil/water cooler - Type PHE Table 1: Dimensions - Type PHE Dimensions [mm] Max. perm. operating Series Type Thread Plates pressure [bar] 4 x ¾“...
- Page 3 Oil/water cooler PHE KTR-N 41412 EN (Plate heat exchanger) Sheet: 3 of 7 Operating/Assembly instructions Edition: Advice 2.1 General advice Please read through these operating/assembly instructions carefully before you start up the oil/water cooler. Please pay special attention to the safety instructions! The operating/assembly instructions are part of your product.
- Page 4 Oil/water cooler PHE KTR-N 41412 EN (Plate heat exchanger) Sheet: 4 of 7 Operating/Assembly instructions Edition: Advice 2.4 Intended use You may only assemble, operate and maintain the oil/water cooler if you • have carefully read through the operating/assembly instructions and understood them •...
- Page 5 Oil/water cooler PHE KTR-N 41412 EN (Plate heat exchanger) Sheet: 5 of 7 Operating/Assembly instructions Edition: Assembly Operating temperature -10 °C to +200 °C Oil/water cooler (plate heat exchanger) made of stainless steel 1.4401 soldered with copper. Please observe boiling and freezing point. 4.1 Assembly / start-up Please note that there may be sharp metal edges on the oil/water cooler due to manufacturing.
- Page 6 Oil/water cooler PHE KTR-N 41412 EN (Plate heat exchanger) Sheet: 6 of 7 Operating/Assembly instructions Edition: Assembly 4.2 Fastening device For fastening the oil/water cooler we recommend to use a fastening retainer as per illustration 3. From size 200 two fastening retainers per oil/water cooler are recommended.
- Page 7 Oil/water cooler PHE KTR-N 41412 EN (Plate heat exchanger) Sheet: 7 of 7 Operating/Assembly instructions Edition: Cleaning Before cleaning please make sure that the oil/water cooler has cooled down. Touching the heated components causes burns. Rinsing allows to remove most of the soft deposits/dirt blocking the interior space. A solution used for rinsing should be a soft acidity with a concentration of less than 5 %, e.
Need help?
Do you have a question about the PHE Series and is the answer not in the manual?
Questions and answers