Page 4
Technical Bulletin No. RTB-006 SUBJECT: F400/F410 Troubleshooting DATE:Nov.30, ’93 PAGE: 7 of 10 9. DJF Original Skew < Phenomenon> If original skews occur as illustrated even if the DJF height is correctly adjusted, perform the following adjustment. Rear Left scale <...
Page 5
No. RTB-008 SUBJECT: DJF Multiple feeding DATE:Nov.30, ’93 PAGE: 1 of 2 PREPARED BY: S. MANO FROM: Copier Technical Support Group CHECKED BY: CLASSIFICATION: MODEL: F400/F410 Action Required Revision of service manual Troubleshooting Information only Retrofit Information Other < Phenomenon >...
Page 6
Technical Bulletin No. RTB-008 SUBJECT: DJF Multiple feeding DATE:Nov.30, ’93 PAGE: 2 of 2 < Countermeasure > Replace the original guide mylars (2 mylars per machine). New part is the assembled part of the mylar and the bracket. New part number is A3761254. For the cut-in serial number, please refer to the modification bulletin which will be issued soon.
Page 7
Technical Bulletin No. RTB-009 SUBJECT: Installation procedure DATE:Nov.30, ’93 PAGE: 2 of 3 3. Caution for DJF shipping tape removal (dual job feeder service manual - installation procedure page, 24) When removing the tape [B] fixing the original press roller shaft [C], be careful to confirm that the shaft is correctly in the holder [D].
Page 8
SUBJECT: DJF feed roller assembly replacement DATE:Nov.30, ’93 PAGE: 1 of 3 PREPARED BY: S.MANO FROM: Copier Technical Support Group CHECKED BY: CLASSIFICATION: MODEL: F400/F410 Action Required Revision of service manual Troubleshooting Information only Retrofit Information Other 1. Manual correction In the feed roller replacement procedure (page 32 to 33), there are steps asking to remove the original table and original guide.
Page 9
Technical Bulletin No. RTB-010 SUBJECT: DJF feed roller assembly replacement DATE:Nov.30, ’93 PAGE: 2 of 3 Before the modification, the middle roller could be shifted to the front when the feed roller was pulled to the front. After the modification, when the feed roller is pulled to the front, the middle roller hits the guide plate and it cannot be moved to the front.
Page 10
Technical Bulletin No. RTB-010 SUBJECT: DJF feed roller assembly replacement DATE:Nov.30, ’93 PAGE: 3 of 3 Rear Front 1. Turn off the main switch then open the feed cover [A]. 2. Remove the guide mylars [B] ( 1 screw each ). 3.
Page 11
DATE:Jan. 31, ’93 SIDED ORIGINAL MODE PAGE: 1 of 3 PREPARED BY: S. MANO FROM: Copier Technical Support Section CHECKED BY: CLASSIFICATION: MODEL: F400/F410 Action Required Revision of service manual DUAL JOB FEEDER Troubleshooting Information only Retrofit Information Other Dual job feeders with the following serial numbers have the possibility that the vertical registration for two sided original mode is improper due to insufficiant inspection during production.
Page 12
Technical Bulletin No. RTB-016 SUBJECT: DJF VERTICAL REGISTRATION ADJUSTMENT FOR TWO DATE:Jan. 31, ’93 SIDED ORIGINAL MODE PAGE: 2 of 3 Two Sided Original Mode VR102 10 ± 2 1. Remove the copier’s left scale [A] (2 screws). 2. Remove the small cover at the rear side on the upper DJF cover then turn on DIP SW 101-2, 101-4, and 102-1.
Page 13
Technical Bulletin No. RTB-016 SUBJECT: DJF VERTICAL REGISTRATION ADJUSTMENT FOR TWO DATE:Jan. 31, ’93 SIDED ORIGINAL MODE PAGE: 3 of 3 8. If the registration cannot be adjusted even though the SP data is changed to the maximum value, return the data to "00". 9.
Technical Bulletin No. RTB-017 SUBJECT: MANUAL CORRECTIONS DATE: Jan. 31,’94 PAGE: 9 of 13 Page 6-19 1.15 • Incorrect 1.15 DUAL JOB FEEDER Definition: [Level:B] Encoder pulse is not detected by the DJF main board..Possible causes DJF feed motor defective DJF transport motor defective DJF feed out motor defective DJF inverter motor defective...
Page 15
Technical Bulletin No. RTB-017 SUBJECT: MANUAL CORRECTIONS DATE: Jan. 31,’94 PAGE: 10 of 13 Page 12 of DJF 3rd line of [Figure 3] explanation • Incorrect A few pulses (0 ∼ 14 pulses: depends on the SP mode adjustment) ..•...
Page 16
Technical Bulletin No. RTB-017 SUBJECT: MANUAL CORRECTIONS DATE: Jan. 31,’94 PAGE:11 of 13 Page 43 of DJF Illustration • Correct • Incorrect Page 46 of DJF Step 6 • Incorrect 6. Confirm that the gap between the trailing edge of the paper and the left edge [C] of the original rear scale is 10 ±...
SUBJECT: Manual Correction DATE: February. 15, 1994 PAGE: 1 of 2 PREPARED BY: S. Mano FROM: Copier Technical Support Section CHECKED BY: CLASSIFICATION: MODEL: F400 DJF Action Required Revision of service manual Troubleshooting Information only Retrofit Information Other MANUAL CORRECTION...
Page 18
120K PM. (48,000 x 2.5 = 120,000) Because the F400/F410 series has an SP mode PM counter (indicates the original feed time since the last PM), you can recognize how many times originals have been fed since the last PM parts replacement.
Page 19
SUBJECT: DJF ORIGINAL DOUBLE FEEDING DATE: Mar. 15 ’94 PAGE: 1 of 2 PREPARED BY: S. MANO FROM: 2nd Technical Support Section CHECKED BY: S. Hamano CLASSIFICATION: MODEL:DJF for F400 series Action Required Revision of service manual Troubleshooting Information only Retrofit Information...
Page 20
Technical Bulletin No. RTB-025 SUBJECT: DJF ORIGINAL DOUBLE FEEDING DATE: Mar. 15 ’94 PAGE: 2 of 2 Countermeasure Clean the separation belt surface with alcohol to recover the separation ability. We recommend to do this at every customer visit including at the installation to eliminate further EM calls.
Page 21
SUBJECT: Irregular original stack in auto counting mode DATE: April 30, ’94 PAGE: 1 of 2 PREPARED BY: S. MANO FROM: 2nd Technical Support Section CHECKED BY: S. Hamano CLASSIFICATION: MODEL: F400 / F410 Action Required Revision of service manual Troubleshooting Information only Retrofit Information Other <PHENOMENON>...
Page 22
Technical Bulletin No. RTB-033 SUBJECT: Irregular original stack in auto counting mode DATE: April 30, ’94 PAGE: 2 of 2 <COUNTERMEASURE> The original stack guide mylar is added. This mylar is attached to the DJF as an accessory. Please install the mylar at installation as shown in the illustration below.
Page 23
FROM: 2nd Technical Support Section CHECKED BY: S. Hamano CLASSIFICATION: MODEL:DUAL JOB FEEDER FOR Action Required Revision of service manual F400/F410/F420 Troubleshooting Information only Retrofit Information Other This is additional information of RTB-025 "DJF double feeding". <PHENOMENON> Original double feeding (two or more sheets of the originals are fed at a time) <POSSIBLE CAUSE>...
Page 24
Technical Bulletin No. RTB-036 SUBJECT: ORIGINAL DOUBLE FEEDING DATE: June 30, ’94 PAGE: 2 of 2 <FIELD COUNTERMEASURE> Replace the separation belts with the new parts. The new part number is A3769502. The material of the separation belts has been changed to the one which less toner adheres to.
Page 25
SUBJECT: SOFTWARE MODIFICATION DATE:Dec. 31, ’94 PAGE: 1 of 7 PREPARED BY: S. Mano FROM: 2nd Technical Support Section CHECKED BY: S. Hamano CLASSIFICATION: MODEL: F400/F410 Action Required Revision of service manual Troubleshooting Information only Retrofit Information Other 1. "A" version ROMs From the following serial numbers, the EPROMs (A0965151 and A0965153) on the main board have been updated to version "A".
Page 26
Technical Bulletin No. RTB-011 SUBJECT: Sorter/DJF Installation DATE: September 15, ’95 PAGE: 1 of 2 PREPARED BY: N. Kaiya FROM: 2nd Technical Support Section CHECKED BY: M. Iwasa CLASSIFICATION: MODEL: DFC - α Action Required Revision of service manual Troubleshooting Information only Retrofit Information Other...
Page 27
Technical Bulletin No. RTB-011 SUBJECT: Sorter/DJF Installation DATE: September 15, ’95 PAGE: 2 of 2 Ferrite Cores Packed with DFC - α For Sorter Installation P/N 16070721 P/N 16070418 For DJF installation P/N 16070638 P/N 16070623...