red roo CMS80 Series Safety Precautions And Operating Instructions

Operating Instructions FOR CMS80 USERS
Operation
OPERATION
Open fuel shut-off valve. Move choke
4)
1) Remove the garden tiller
1) Remove the garden tiller
control to CHOKE or START position.
from its trailer/carrier. Use caution.
from its trailer/carrier. Use caution.
aution.
Note: Choke must fully close. Move throttle
2) Familiarize yourself with the machine and its
2) Familiarize yourself with the machine and its
controlto RUN or FAST position. If engine is
controls.
machine and its
controls.
equipped with rocker style stop switch, push
RUN or I (I = Ignition) before starting. Rewind
3) Ensure the safety clutch control lever is in the
3) Ensure the safety clutch control lever is in the
Starter: Grasp rope
disengaged position. The safety clutch
disengaged position. The safety clutch
trol lever is in the handle and pull slowly
control lever is located on the left handle bar.
control lever is located on the left handle bar.
until resistance is felt
The disengaged position of the lever is down.
OPERATING INSTRUCTIONS FOR SG350
e safety clutch The disengaged position of the lever is down.
to prevent kickback.
e left handle bar. 4) Remove the shaft locking pin located behind
Then pull cord rapidly
4) Remove the shaft locking pin located behind
the wheel axle. Store pin in hole provided on
to overcome compression, and start engine.
4) IGNITION: Must be in "ON" position to start. the wheel axle. Store pin in hole provided on
he lever is down.
left hand side of handle bar. Repeat if necessary with choke off and throttle
"OFF" to stop.
left hand side of handle bar.
control at maximum rpm (FAST position). Operate
n located behind
5) The wheel axle will now pivot. Lift up on the
5)
5) The wheel axle will now pivot. Lift up on the Open fuel shut-off valve. Move choke
the engine at maximum rpm (FAST position).
handle to allow wheel axle to pivot. For
hole provided on
handle to allow wheel axle to pivot. For
control to CHOKE or START position.
5) MULCHER/SHREDDER HOPPER (See Figure 1)
Transport, keep the wheel axle forward. When
transport, keep the wheel axle forward. When
Note: Choke must fully close. Move throttle As the engine ignition begins, the engine shaft
cultivating, keep the wheel axle rearward for
cultivating, keep the wheel axle rearward for
operates freely until approximately 1600 rpm at
controlto RUN or FAST position. If engine is
added stability and control.
added stability and control.
ot. Lift up on the
which speed the centrifugal clutch engages and
equipped with rocker style stop switch, push
DO NOT transport the tiller with the wheel
DO NOT transport the tiller with the wheel
begins driving the rotor. Proper rotor rpm is 2900
RUN or I (I = Ignition) before starting. Rewind
le to pivot. For
axle in the rear position.
axle in the rear position.
rpm with a plus or minus tolerance of 100 rpm.
Starter: Grasp rope
le forward. When
In this condition you have four rows of hammers
6) Adjust depth shoe (if equipped) by removing handle and pull slowly
6) Adjust depth shoe (if equipped) by removing
literally cutting or beating material until it reaches
axle rearward for shaft locking collar and sliding depth shoe to until resistance is felt
shaft locking collar and sliding depth shoe to
such fractinal size as, to allow it to pass through
to prevent kickback.
desired position. Replace shaft locking collar.
desired position. Replace shaft locking collar. the grinding screen. The grinding screen retains
Then pull cord rapidly
the material within the grinding chamber for
7) Open fuel shut-off valve. Set choke
r with the wheel
7) Open fuel shut-off valve. Set choke
to overcome compression, and start engine.
several seconds until the free-swinging hammers
control to Choke or Start position.
Repeat if necessary with choke off and control to Choke or Start position.
have rotated several times. The number of cuts
Set throttle control to Run or Fast
throttle control in FAST position. Operate
by the hammers and, of course, retention time Set throttle control to Run or Fast
position. Set engine
engine in FAST position. within the chamber varies with each type of
position. Set engine
ped) by removing
stop switch to On or organic material.
stop switch to On or
NOTE: The operator presence control bar is
ng depth shoe to
Run position. Pull
Run position. Pull
6) CHIPPER HOPPER (See Figure 1) Branches designed as a safety feature. The engine will
aft locking collar. starter cord rapidly.
starter cord rapidly.
are fed into the side hoppper for chipping. One
not start or operate without depressing the
Repeat (if necessary)
at a time if they are thicker than 50mm, several
Repeat (if necessary)
control bar. See Figure 1 (next page).
with choke off.
alve. Set choke together if of small diameter. The throat opening
with choke off.
6) Push the stump grinder to the stump,
is approximately 80mm (3
Start position.
8) When in position to begin garden tilling,
position the grinding disc over the front edge
8) When in position to begin garden tilling,
or side branches may have to be trimed from the
engage the safety clutch control lever. The
o Run or Fast main stalk before the chipping process occurs.
engage the safety clutch control lever. The of the stump.
tynes will begin rotating. Wheel axle must be in Short stubs of branches may be pushed through
tynes will begin rotating. Wheel axle must be in
7) Set the wheel brake on the right hand side of
the chipper section with the next branch. Never
the rear position while tilling. Release the
the rear position while tilling. Release the
the stump grinder and adjust the handle
assume to know the location of the blades and
safety clutch control lever to stop the tynes
safety clutch control lever to stop the tynes
position to achieve better leverage
try to process short branches by hand. BE
rotating. Tyne speed is governed by engine
rotating. Tyne speed is governed by engine
depending on the height of the stump.
SAFE, KEEP YOUR HANDS AWAY FROM THE
throttle setting.
throttle setting.
CHIPPING BLADE AND ROTATING HAMMERS.
8) Use the throttle to gradually bring the engine
RPM s up to full while lifting the grinding
WARNING! – KEEP HANDS AND
7) CAUTION: IF MULCHER/SHREDDER
WARNING! – KEEP HANDS AND
disc off the ground.
CHUTE CLOGGS WITH MATERIAL, FEET CLEAR OF TYNES AT ALL
FEET CLEAR OF TYNES AT ALL
STOP THE ENGINE IMMEDIATELY TO
TIMES!
9) Slowly lower the stump grinder until the
TIMES!
PREVENT CLUTCH DAMAGE.
n garden tilling, grinding disc comes in contact with the
stump. Move the stump grinder back and
ontrol lever. The
forth in a slow sweeping motion.
ORGANIC MATERIAL IS YOUR RESPONSIBILITY.
NO STICKS OR BRANCHES LARGER THAN 19MM OR 3/4" DIAMETER INTO THE LARGE SHREDDER
HOPPER (PART NO. 0805-0001)
9) Do not hurry the job. Proceed slowly and allow
9) Do not hurry the job. Proceed slowly and allow
9) Do not hurry the job. Proceed slowly and allow
ONLY OPERATE THE CHIPPER-MULCHER-SHREDDER FROM THE OPERATOR ZONES AS SHOWN.
the machine time to do the job. When ground
Figure 1
is extremely hard, reduce engine speed.
WARNING! – IN CASE OF DIFFICULTY,
DISENGAGE THE SAFETY CLUTCH
CONTROL LEVER. ALL TILLING ACTION
STOPS. Press the engine "STOP" button
10) Stop Engine: Release the safety clutch control
located on the engine.
10) Stop Engine: Release the safety clutch control
10) Stop Engine: Release the safety clutch control
lever. Move throttle to Slow position. Set engine
stop switch to Stop or Off position. DO NOT move
10) When the front part of the stump has been
choke control to Choke
removed, release the brake and push the stump
grinder forward to a new edge.
or Start position to stop
8) Do not allow an accumulation of processed material
NOTE: For better performance and to avoid

AFTER USE

to build up under the discharge of the shredder as this
AFTER USE
engine. Backfire or
may prevent shredded material to discharge and will excessive clutch wear, run the engine at full
engine damage may
result in clogging. Operate the machine at maximum
throttle during operation.
1)
1)
rpm's (fast position).
occur.
9)
2) Allow machine to cool down.
2) Allow machine to cool down.
AFTER USE
3) Wash mud and dirt off of the garden tiller.
3) Wash mud and dirt off of the garden tiller.
CHIPPER CHUTE OR DISCHARGE AREA OF THE
MULCHER/SHREDDER
1) Turn fuel shut off valve to the "OFF"
4) Remove any weeds, wire, rope or other
4) Remove any weeds, wire, rope or other
10) Always stand clear of the discharge area when the
position.
shredder is running. Never reach into this area.
11) After stump has been removed use the throttle to
(See Figure 1).
gradually bring down the engine RPM s. Make sure
2) Allow machine to cool down.
5) Return wheel axle to forward position for
5) Return wheel axle to forward position for
the grinding disc has come to a complete stop
11) Keep your face and body back from the feed
hopper to avoid being struck by any material that
before moving the stump grinder.
3) Wash mud and dirt off of the garden tiller.
may bounce back. Do no over-reach, keep proper
12) Stop Engine: Do not
6) Return depth shoe (if equipped) to full Up
Ensure no water enters the carburettor. 6) Return depth shoe (if equipped) to full Up
balance and footing.
move choke control to
1
") square, side chutes 12) Stop Engine: Do not move choke control to CHOKE CHOKE position to stop
4) Remove any weeds, wire, rope or other
2
position to stop engine. Backfire or engine damage
engine. Backfire or
material that may have wrapped around the
may occur, Move throttle control to SLOW postition,
engine damage may occur. Move throttle control
then push rocker switch to 0 (STOP).
tynes and rotor assembly.
to SLOW position, then push rocker switch to 0
(STOP), or turn key to OFF, if equipped.
5) Return wheel axle to forward position for
AFTER USE
transport. Replace shaft locking collar.
1)
6) Return depth shoe (if equipped) to full Up
2)
Wash mud and dirt off of the stump grinder.
position.
Ensure no water enters the carburettor.
3) Remove any weeds, wire, rope, etc. that may
© Copyright 2001, Red Roo Sales & Service Company Pty. Ltd.
© Copyright 2001, Red Roo Sales & Service Company Pty. Ltd.
have wrapped around the disc grinding shaft assembly.
© Copyright 2014, Red Roo Sales & Service Company Pty. Ltd.
4) CHECK FOR LOOSE BOLTS ON THE GRINDING DISC.
the machine time to do the job. When ground
the machine time to do the job. When ground
is extremely hard, reduce engine speed.
is extremely hard, reduce engine speed.
WARNING! – IN CASE OF DIFFICULTY,
WARNING! – IN CASE OF DIFFICULTY,
DISENGAGE THE SAFETY CLUTCH
DISENGAGE THE SAFETY CLUTCH
CONTROL LEVER. ALL TILLING ACTION
CONTROL LEVER. ALL TILLING ACTION
STOPS. Press the engine "STOP" button
STOPS. Press the engine "STOP" button
located on the engine.
located on the engine.
lever. Move throttle to Slow position. Set engine
lever. Move throttle to Slow position. Set engine
stop switch to Stop or Off position. DO NOT move
stop switch to Stop or Off position. DO NOT move
choke control to Choke
choke control to Choke
NOTE: Make sure grinding disc has
or Start position to stop
or Start position to stop
stopped completely before clearing debris
engine. Backfire or
engine. Backfire or
Maximum Diameter
engine damage may
19mm or 3/4"
engine damage may
Part # 0805-0001
occur.
occur.
Know the controls and how to shut the unit down in an emergency.
Never clear the discharge area with hands, feet, or any other part of your body.
Never clear the discharge area while the Chipper/Mulcher/Shredder is running.
After unit is shut off, use a long handle tool to clear the area of mulch.
Turn fuel shut off valve to the "OFF"
Turn fuel shut off valve to the "OFF"
THIS MACHINE IS CAPABLE OF INFLICTING SERIOUS INJURY IF OPERATED
position.
WARNING! – Keep hands and feet
IMPROPERLY. READ WARNING AND CAUTION DECALS ON MACHINE
position.
NEVER ALLOW YOUR HANDS OR ANY PART clear of the Grinding Disc and grinding
OF YOUR BODY OR CLOTHING INSIDE THE zone and other moving parts while
MULCHER/SHREDDER/HOPPER OR
engine is running. 6
Ensure no water enters the carburettor.
WARNING! – In case of difficulty, release
Ensure no water enters the carburettor.
the Operator Presence Control Bar. This
action will stop the engine. See figure 1.
material that may have wrapped around the
material that may have wrapped around the
tynes and rotor assembly.
tynes and rotor assembly.
transport. Replace shaft locking collar.
transport. Replace shaft locking collar.
position.
position.
Turn fuel tap to "OFF" position.
Allow machine to cool down.

SAFETY PRECAUTIONS

SAFETY PRECAUTIONS
SAFETY PRECAUTIONS
AND OPERATING
AND OPERATING
AND OPERATING
INSTRUCTIONS
INSTRUCTIONS
INSTRUCTIONS
SAFETY PRECAUTIONS
AND OPERATING
INSTRUCTIONS
GT622
GT622
CMS80FW
GARDEN
GARDEN
CMS80T
TILLER
TILLER
CHIPPER/MULCHER/SHREDDER
GT622
SG350
Commercial Environmental Equipment
GARDEN STUMP
Commercial Environmental Equipment
Online Demonstration Available at:
1301-0018
1301-0018
www.redroo.com/products/mulcher
P/N 1301-0021
™
™
™
™
Profile No. : 631
Name : Red Roo CMS80 CHIPPER / MULCHER / SHRE
Scan Code