Advertisement
4.2.
sequence of assembly
4.2.1.
Align (items 5, 1 and 6) as shown in fig.3, then pass the pivot spindle (item 2) through all three items with equal projection. correct
orientation is critical. note (item 5) has a longer boss than (item 6) which makes it easier to identify, both are assembled with the lug
projecting inboard. orientation of (item 1) is clearly shown by the position of the tapped hole for the pinch knob (item 11).
4.2.2.
Spring (item 7) over ends of pivot spindle paying particular attention to the position of the lug on the boss shown in fig.5. Do not over
bend the loop when fitting over spindle, this note also applies when fitting (items 8, 9 and 10).
4.2.3.
Spring (item 8) over ends of pivot spindle paying particular attention to the position of the lug on the boss shown in fig.5.
4.2.4.
Spring (item 9) over ends of pivot spindle paying particular attention to the position of the lug on the boss shown in fig.5.
4.2.5.
Spring (item 10) over ends of pivot spindle paying particular attention to the position of the lug on the boss shown in fig.5.
4.2.6.
Place washer (item 3) at each end of spindle and wind on hexagon stiff nuts (item 4) with equal engagement, without clamping the
assembly. All loops to pivot freely under their own weight, limited only by the lugs.
4.2.7.
Fit pinch knob (item 11) until flush with inside face of bracket (without protrusion).
4.3.
fitting to sealey re231, re2311 and re232 coil spring compressors
4.3.1.
read these instructions in conjunction with re231, re2311 or re232 spring compressor instructions. As explained in section 1;
always fit the restraining chain around strut and spring fig.3 (single restraint). strut and spring compression station should be securely bolted to
the workshop floor before use.
4.3.2.
offer complete assembly as shown in fig.4 on to the vertical column of the spring compressor.
4.3.3.
With the pinch knob, clamp the assembly at the desired height such that incremental holes in the column align with holes in the restraint bracket
lugs. Do not over-tighten deforming pillar or bracket. this height position is determined by the position of the spring being compressed.
4.3.4.
finally insert a m12 X 75 bolt through the restraint bracket lugs and column; retain with a m12 hexagon nut.
single restraint
fig.6
5. operation
5.1.
All the loops of the restraint system, except item 5, can be readily swept up and away from the work area. these loops go beyond the vertical to
a self supported leaning position. item 5 swept path is limited by a mechanical stop.
6. maintenance
6.1.
the robust nature of the restraint system means that it only requires cleaning after use with a lightly oiled cloth.
6.2.
check freedom of loop sweep, which should result from the cleaning/lubricating process in 6.1.
6.3.
replace immediately any part that is or appears to be damaged.
environmental protection
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
important: no liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack sealey limited
sole uK distributor, sealey Group.
Kempson Way, suffolk Business Park,
Bury st. edmunds, suffolk.
iP32 7Ar
Original Language Version
aDDitional
restraint
fig.7
01284 757500
01284 703534
re23rs | issue 2 12/05/17
www.sealey.co.uk
sales@sealey.co.uk
Advertisement
