Related Manuals for Nagra MPS
Summary of Contents for Nagra MPS
- Page 1 MPS – Multiple Power Supply User manual P/N: 2055100159 All rights reserved – © 2014 rev 1...
-
Page 2: Table Of Contents
LED and Modulometer intensity adjustment ..........10 Remote control ..................11 MPS with battery option ................. 12 Starting the MPS using the trigger input REM ........... 13 Using the trigger output AMP ..............13 Case cleaning ..................13 Technical specifications ................14 Déclaration de conformité... -
Page 3: Safety Warning
There are no user adjustments inside the MPS, do not attempt to open it. Warranty Audio Technology Switzerland SA, certifies that this device has been inspected and tested before leaving our factory. -
Page 4: Congratulations
Development department. Nagra has launched a Hi-Fi range to allow a wider public to benefit from technical advances that are often the privilege of the professionals. The MPS will enhance your Nagra system and allow you to access better sonic performance and enjoy your music more. Thank you for your confidence. -
Page 5: Installation
VFS (before 2012). Feel free to contact your Nagra dealer for more information. it is not advised to place other Nagra units above or below the MPS, as it features a large transformer. It is preferable to use a separate shelf for other devices. -
Page 6: Front Panel
Connecting the mains Place the front panel selector in the OFF position, marked “O”. Insert the IEC cable into the connector on the rear of the Nagra MPS. You may then push the mains switch to the “I” position. Nagra –... -
Page 7: Which Output To Use
If your MPS has the internal battery option installed, we recommend using the battery output #1 for any analog equipment particularly for phono stages such as the VPS or the Melody with the phono option. -
Page 8: Fuse Replacement
Operating the MPS These are the functions available from the main selector. (Remote) The MPS will be turned on and off by the remote control, or the input trigger, for more information see page 13 The MPS is in standby position (the internal battery, if fitted, will recharge) -
Page 9: Nagra Modulometer
The MPS only displays the voltage, it does not affect it. BAT displays the battery level from 12 to 17 V. The output level of a fully charged battery is 16.8 V. -
Page 10: Remote Control
Remote control Factory settings for the remote control The Nagra MPS is factory set to be device number 6 with Nagra remote control code. Changing device number (for dealers) If you wish to use another device number, turn the MPS Off and unplug the mains cable. -
Page 11: Mps With Battery Option
Recharging Full charge reached NB If the BAT position is selected yet the battery charge is too low, the MPS will automatically begin to recharge. In this case, output 1 will be fed from the mains and no longer from the battery. -
Page 12: Starting The Mps Using The Trigger Input Rem
Connected to the ground Open or connected to max 12 V rms Note, in this case, in the ON position, the MPS does not run on battery. If you wish to use the battery, you need to turn the main selector to BAT. -
Page 13: Technical Specifications
Technical specifications Compatibility Nagra PL-L, VPS, BPS, Jazz, Melody preamplifiers Nagra CD players Output type 1 to 4, 12 V DC, 1 A Lemo connector BPS output 9 V, 100 mA Or 12 V by selector Linear noise 100 μV maximum... -
Page 14: Déclaration De Conformité Ce
Déclaration de conformité CE CE Declaration of conformity FABRICANT: AUDIO TECHNOLOGY SWITZERLAND SA, 1032 Romanel, SUISSE MANUFACTURER: AUDIO TECHNOLOGY SWITZERLAND SA, 1032 Romanel, SWITZERLAND APPAREIL: Nagra MPS MODEL: Nagra MPS NORMES APPLICABLES: APPLICABLE NORMS: Champ électromagnétique rayonné EN 55022 Cl. B Radiated electromagnetic field EN 55022 Cl.