Subscribe to Our Youtube Channel
Related Manuals for MMM CO2 Series
Summary of Contents for MMM CO2 Series
- Page 1 Instructions for use INCUBATOR CO2Cell 190 Comfort CO2Cell 190S Comfort (with sterilization 200 °C) CELL Comfort 190_np_en 1301_mmm_V1.02...
-
Page 3: Table Of Contents
CONTENTS: 24. 1. 2013 SAFETY ..............................3 ..........................3 EGAL CONSIDERATIONS ............................3 NTENDED USE ........................3 YMBOLS USED IN THIS MANUAL ......................... 3 ENERAL SAFETY INSTRUCTIONS DESCRIPTION .............................3 ............................4 ONSTRUCTION ..............................4 OORS ............................4 ONTROL SYSTEM ............................4 SENSOR ..............................4 IAGRAMS 2.5.1 ............................ - Page 4 ............................. 11 TART LOGGING ..........................12 HANGING FILENAME ......................... 12 EMOVING THE SD CARD HIGH TEMPERATURE STERILISATION ....................13 ............................13 REPARATION ..........................13 TARTING THE CYCLE ........................... 13 TERILISE CYCLE ............................14 OOLING PHASE ....................... 14 BORTING THE STERILISE CYCLE ERROR MESSAGE SCREENS .........................
-
Page 5: Safety
It is important that you read this manual can perform repairs or maintenance on this incubator. Only completely and observe all instructions. original spare parts from MMM can be used. There are no Failure to follow these instructions may result user serviceable parts within the incubator. -
Page 6: Construction
PC so that you can remotely access the SD card data. PC software is required to do this. Contact your dealer or MMM directly for advice. Other optional communication options are Ethernet PC interface and 4-20 mA retransmit. -
Page 7: Delivery Transportation And Storage
Keep these safe. MMM do not recommend placing the incubator directly on Please check that the accessory pack contains the following Wheeled platform forms are available that lift the incubator items. -
Page 8: Shelves And Usable Space
(15 psi) will damage the incubator so a pressure reducing valve (PRV) must be used. The CO inlet to the incubator is via a 4 mm barbed push can be supplied by MMM. Section 10. For correct connection of CO , follow these steps in order: supply. -
Page 9: Getting Started
Instructions for use Plug the supplied power lead into the IEC connector on the MAIN DISPLAY rear of the incubator. The main screen shows chamber set points (SP) and Plug the other end of the IEC lead into the electrical supply. process values (PV). -
Page 10: Changing Co
Instructions for use Use the keypad to Use the keypad to change the low alarm change the low alarm threshold. threshold. This must be negative This must be negative press press Press Press selection. selection. CHANGING CO SET POINTS AND ALARM STATUS SCREEN ALARM THRESHOLDS To change the temperature set point, touch this area of the... -
Page 11: Other Features
Instructions for use As an additional warning the colours of the process values The CO graph is viewed in the same manner. change during alarm condition. UTILITY MENU The temperature process On the main screen press the utility menu symbol: value has changed colour from black to red. -
Page 12: Door Alarm Menu
To enter a user name and password press the User icon: Press the info icon: The information screen shows the incubator Serial Number is using. This information is important should you require any assistance from MMM. Press here on Line 1 to enter user name. Press: save. -
Page 13: Logging Out
Please be patient. SD card is pre-formatted to work with the controller’s operating system. Only cards supplied by MMM can be used. Using any other type of card will not work with the incubator and will cause the controller system to crash. -
Page 14: Changing Filename
Instructions for use CHANGING FILENAME REMOVING THE SD CARD Always perform the following steps before removing the SD Card. Failure to follow 12345. Enter these steps will results in corrupted data. On the SD Card status screen press the SD card tools icon: Press to store selection. -
Page 15: High Temperature Sterilisation
Instructions for use This shows that the door locks have activated and that HIGH TEMPERATURE Operator 6 is logged on. STERILISATION Risk of damage to unit. The Comfort 190 is not intended to be used as an autoclave and must not be used for sterilising Press any other equipment. -
Page 16: Cooling Phase
Chamber probe failure Chamber probe is out of Press to continue limits and has failed. to main screen. Contact MMM Service immediately Base probe failure Base probe is out of limits and has failed. Contact MMM Service immediately... -
Page 17: Options
A RETRANSMISSION RETX This is the list of some of the accessories currently available. Please contact MMM if the part you require is not listed. ordering. This feature allows the chamber temperature and CO PTSK Stacking kit for 2 x Comfort 190 process values to be retransmitted as a 4 - 20 mA signal. -
Page 18: Cleaning
All MMM Comfort 190 incubators are supplied with a two surfaces. year manufacturer’s warranty from the date of installation. Disconnect before cleaning. Registration Card and post to MMM Limited or to your local Completely dry the unit before distributor. reconnecting the power. -
Page 19: Disposal
(inches) 925 (36.4) waste recycling companies. Height mm (inches) 1080 (42.5) Depth mm (inches) 850 (33.5) Contact MMM for further information regarding WEEE regulations. WEIGHT Comfort 190, Net kg (lbs) 94.5 (208) Comfort 190S, Net kg (lbs) 104 (229) - Page 20 Instructions for use CO2CELL Comfort 190_np_en 1301_mmm_V1.02...
- Page 24 ¡ ¢ £ ¡ ¤ ¥ ¡ ¦ § ¨ ¤ ¦ ¨ £ © ¥ ¤ ¡ ¤ ¡ ¡ ¡ ¨ ¥ ¦ ¡ " & ¤ ¡ ¡ ¦ ¤...
Need help?
Do you have a question about the CO2 Series and is the answer not in the manual?
Questions and answers