ROBBE ROCONTROL Manual

ROBBE ROCONTROL Manual

Programming card

Advertisement

Quick Links

SAFETY INSTRUCTIONS

General Hazard Information

Please note for all our deliveries: Please read these safety and hazard notes first, and then read
through all operating and assembly instructions completely and carefully before commissioning for
the first time. Remote-controlled models are not a toy and must be used by children under the age
of 14 years only under the constant supervision of adults who are familiar with construction,
operation, materials and potential hazards. The construction, commissioning and operation of
remote-controlled models are dangerous and are the operator's responsibility. We expressly point
out these dangers and assume no liability. Careful, well-considered handling during operation
protects against personal injury and damage to property. Carry out maintenance and inspection of
your models and electrical equipment at short, regular intervals. Regularly check the secure fit of
all fasteners.
Applies to all remote-controlled models:
• Make sure that nobody else in the environment uses your transmission frequency.
• switch on: Switch on the transmitter first and then switch on the receiver.
• turn off: Turn off the receiver first, then turn off the transmitter.
• Make sure that the transmitter and receiver are fully charged before starting.
In addition, please observe the following instructions:
• Do not use different types of batteries or rechargeable batteries or new and used batteries
together. Remove dead batteries from the equipment, especially if they are not used for a
long time.
• Never expose electrical equipment to dirt, dust, moisture, cold or heat. Cable damage can
lead to short circuit, fire and destruction of the devices!
• Avoid injury through caution in all activities with your models.
• Check with your insurance company whether the risks arising from your models are covered
by liability insurance or whether you have to insure them additionally.
• Adhesives and varnishes contain solvents that can be harmful to health. Follow the
manufacturer's instructions and warnings.
Programming card
Dear customer, we are pleased that you have chosen the
programming card from our product range. With this device
you
have
a
powerful
ROCONTROL controller.
Despite the relatively simple operation of the programming
card, its use requires some knowledge from you. These
instructions will enable you to quickly familiarize yourself with
the possibilities of the programming card. To achieve this goal
safely and quickly, you should read the operating instructions
carefully before starting up the device.
tool
to
easily
program
your

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ROCONTROL and is the answer not in the manual?

Questions and answers

Summary of Contents for ROBBE ROCONTROL

  • Page 1 ROCONTROL controller. Despite the relatively simple operation of the programming card, its use requires some knowledge from you. These instructions will enable you to quickly familiarize yourself with the possibilities of the programming card. To achieve this goal safely and quickly, you should read the operating instructions carefully before starting up the device.
  • Page 2 Instruction manual ROCONTROL programming card Hazard warnings Flight models Please contact experienced model pilots, clubs or flight schools for information on reducing hazards and avoiding damage. Ask all spectators to observe a safety distance of at least 5 m. Never direct your model airplane towards people, animals or high-voltage lines. Avoid public roads, pathways, squares and places where people may be present.
  • Page 3 Instruction manual ROCONTROL programming card and at 300 - 600 charging cycles, they have to reckon with a drop in performance of only approx. 20%.  With a non-optimal charger, the capacity is significantly reduced with every charge/discharge and thus also the service life. Storage at too high or too low temperatures may cause a gradual reduction in capacity.
  • Page 4 Instruction manual ROCONTROL programming card Special instructions for discharging LiPo batteries A continuous current of approx. 15 C is no major problem for the LiPo batteries. For larger currents, please refer to the information in the respective product data sheets. A discharge to below 2.5 V per cell permanently damages the cells.
  • Page 5 (see Table 1). • For controllers with HV operating voltage, as the ROCONTROL PRO 130 A, HV OPTO, the four LEDs indicate the number of cells of the connected LiPo batteries (see Table 2). Seite...
  • Page 6 B. For controllers without BEC device If the controller is marked with "OPTO", like the ROCONTROL PRO 130 A HV OPTO, this means that this controller does not have an integrated BEC, then an additional battery (4.8 - 6.0 V) must be used to operate the programming card.
  • Page 7 Instruction manual ROCONTROL programming card table 1: music function deactivated List of characteristic music rhythms table 2: automatic detection List of connected LiPo automatic detection cells automatic detection automatic detection automatic detection automatic detection automatic detection LED glows automatic detection...
  • Page 8 Modellbau Lindinger GmbH Telefon: +43(0)7582/81313-0 , info@robbe.com, UID Nr.: ATU69266037 Modellbau Industriestrasse 10 „robbe Modellsport“ ist eingetragenes Markenzeichen der Modellbau Lindinger GmbH 4565 Inzersdorf im Kremstal Irrtum, Druckfehler und technische Änderungen vorbehalten. Copyright Modellbau Lindinger 2018 AUSTRIA Kopie und Nachdruck, auch auszugsweise, nur mit schriftlicher Genehmigung.

Table of Contents