ROBBE rocontrol PRO Quick Start Manual
ROBBE rocontrol PRO Quick Start Manual

ROBBE rocontrol PRO Quick Start Manual

Programming box

Advertisement

Quick Links

SAFETY INSTRUCTIONS

General Hazard Information
Please note for all our deliveries: Please read these safety and hazard notes first, and then read
through all operating and assembly instructions completely and carefully before commissioning for
the first time. Remote-controlled models are not a toy and must be used by children under the age
of 14 years only under the constant supervision of adults who are familiar with construction,
operation, materials and potential hazards. The construction, commissioning and operation of
remote-controlled models are dangerous and are the operator's responsibility. We expressly point
out these dangers and assume no liability. Careful, well-considered handling during operation
protects against personal injury and damage to property. Carry out maintenance and inspection of
your models and electrical equipment at short, regular intervals. Regularly check the secure fit of
all fasteners.
Applies to all remote-controlled models:
• Make sure that nobody else in the environment uses your transmission frequency.
• switch on: Switch on the transmitter first and then switch on the receiver.
• turn off: Turn off the receiver first, then turn off the transmitter.
• Make sure that the transmitter and receiver are fully charged before starting.
In addition, please observe the following instructions:
• Do not use different types of batteries or rechargeable batteries or new and used batteries
together. Remove dead batteries from the equipment, especially if they are not used for a
long time.
• Never expose electrical equipment to dirt, dust, moisture, cold or heat. Cable damage can
lead to short circuit, fire and destruction of the devices!
• Avoid injury through caution in all activities with your models.
• Check with your insurance company whether the risks arising from your models are covered
by liability insurance or whether you have to insure them additionally.
• Adhesives and varnishes contain solvents that can be harmful to health. Follow the
manufacturer's instructions and warnings.
Programming Box
Dear customer, we are pleased that you have chosen the
LED Programming Box from our assortment. With this device
you have a powerful tool to program your ROCONTROL PRO
controllers comfortably.
Despite the relatively simple operation of the programming
box, its use requires some knowledge from you. These
instructions will enable you to quickly familiarize yourself with
the possibilities of the programming box. To achieve this goal
safely and quickly, you should read the operating instructions
carefully before starting up the device.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the rocontrol PRO and is the answer not in the manual?

Questions and answers

Summary of Contents for ROBBE rocontrol PRO

  • Page 1 Programming Box Dear customer, we are pleased that you have chosen the LED Programming Box from our assortment. With this device you have a powerful tool to program your ROCONTROL PRO controllers comfortably. Despite the relatively simple operation of the programming box, its use requires some knowledge from you.
  • Page 2 Instruction manual ROCONTROL PRO Programming Box Hazard warnings Flight models Please contact experienced model pilots, clubs or flight schools for information on reducing hazards and avoiding damage. Ask all viewers to maintain a safety distance of at least 5 m. Never direct your model airplane towards people, animals or high-voltage lines.
  • Page 3 Instruction manual ROCONTROL PRO Programming Box life and with 300 - 600 charging cycles you have to expect a drop in performance of only approx. 20%. With a non-optimal charger, the capacity is significantly reduced with every charge/discharge  and thus also the service life. Storage at too high or too low temperatures may cause a gradual reduction in capacity.
  • Page 4 Instruction manual ROCONTROL PRO Programming Box Special instructions for discharging LiPo batteries A continuous current of approx. 15 C is no major problem for the LiPo batteries. For larger currents, please refer to the information in the respective product data sheets. A discharge to below 2.5 V per cell permanently damages the cells.
  • Page 5 40 g Application possibilities In addition to our ROCONTROL PRO controllers, the LED program box also works with other controller types for brushless motors from the Chinese manufacturer. The box cannot be used for motor controllers from other manufacturers. For the different types of controllers from our manufacturer, there are corresponding labels for the front and rear panel.
  • Page 6 Instruction manual ROCONTROL PRO Programming Box programming procedure 1. Apply the corresponding label on the front and rear side (optional) The labels for a car or ship controller are attached to the front and rear of the box  at the factory. To program such controllers, it is not necessary to re-label the box.
  • Page 7 Instruction manual ROCONTROL PRO Programming Box 2) For controllers with one fan The connection for the fan is also the programming connection. In this case, disconnect the fan cable from the controller and then insert one end of the enclosed programming cable (included in the scope of delivery) there and the other end into the programming connection of the box, which is marked with "- / +/ impulse".
  • Page 8 Modellbau Lindinger GmbH Telefon: +43(0)7582/81313-0 , info@robbe.com, UID Nr.: ATU69266037 Modellbau Industriestrasse 10 „robbe Modellsport“ ist eingetragenes Markenzeichen der Modellbau Lindinger GmbH 4565 Inzersdorf im Kremstal Irrtum, Druckfehler und technische Änderungen vorbehalten. Copyright Modellbau Lindinger 2018 AUSTRIA Kopie und Nachdruck, auch auszugsweise, nur mit schriftlicher Genehmigung.

Table of Contents