Advertisement
Quick Links
Advertisement
Related Manuals for Baton POS1CC11
Summary of Contents for Baton POS1CC11
- Page 1 20191002 OWNERS MANUAL POS1CC11...
-
Page 2: Chapter 1: Introduction
Chapter 1: Introduction... - Page 3 Page 1 POS1 Structure characteristic and Specification ●Carbon brush electric conduction, the copper alloy outer cover dispels the heat. ●Internal diameter 60mm. Pass through holes ●Air cooling, duty cycle 300A / 100% ●The table is electroplated, it is not apt to stick dregs. ●All right use of two sides of the table.
- Page 4 Page 2 1.2 POS1 Structure POS-1A Positioner Eccentric Load A : Eccentric Center (mm.) POS-1A Center of Gravity B :Center of Gravity (mm.) POS-1B Positioner Eccentric Load POS-1C Positioner Eccentric Load POS-1D Positioner Eccentric Load A : Eccentric Center (mm.) A : Eccentric Center (mm.) A : Eccentric Center (mm.) POS-1B Center of Gravity...
- Page 5 POS1 Size Page 3 ØA ØF POS1 POS2 340mm 340mm 375mm 418mm 276mm 319mm 206mm 206mm 220mm 220mm 10mm 10mm UNIT:mm...
- Page 6 Page 1 COM-1100 Finction Specification / No. COM-1100 Power A1: AC110V/60Hz/4A A2: AC230V/50Hz/3A Rotate the direction cw/ccw Arc way of the welde Standard Line welder Stop the brake Magnetism brake H.F. Protect Start the device Foot switch (Line 2M)
- Page 7 Page 2 Structure characteristic ○Welding method that can be matched ●MIG/MAG ●TIG ●Wire-TIG ●Plasma weld ●SAW ○Dispose the place ●In the factory ○Duty cycle ●Can operate in succession100% ●Weld electric current 300A...
-
Page 8: Chapter 2: Machine Installation
Chapter 2: Machine Installation... - Page 9 Page 3 Installation Weld power source source...
- Page 10 Page 7 2.2 Install the method of the drive motor Adj. move Permit to move 3 - 5mm. drive motor Rotate the table and confirm moving the distance(3 - 5 mm) with hands, lock the drive motor...
-
Page 11: Chapter 3: Machine Operating
Chapter 3: Machine Operating... - Page 12 Page 4 Control Panel 1.Power switch 2.Power light 3.FUSE 4.Table speed (RPM) 5.Table cw/ccw switch 6.Hold / Inch switch 7.Welder switch...
- Page 13 Page 5 Inch operating Inch Standard Link Start switch Power switch on Inch switch to down Welder switch to up Light Rotate speed ( RPM) Rotate the direction cw/ccw Table and welder off Table and welder on Light Stop switch Light...
- Page 14 Page 6 Hold operating Hold Standard Link Switch to hold mode Turn on the welder switch Start switch Power switch on Light Rotate the direction cw/ccw Rotate speed ( RPM) Table and welder off Table and welder on Stop switch...
- Page 15 Page 7 Table start and accelerate time to adjust Accelerate time to increase ACCEL t(sec) ACCEL Accelerate time to reduce Open the control panel DC motor driver...
- Page 16 Page 8 The time of the timer range adjusting Open the control panel SW1 SW2 SW3 SW4 OFF ON OFF ON OFF ON OFF OFF OFF OFF...
- Page 17 Appendix...
- Page 18 Warn the item TIG Welder TIG Welder TIG Welder...
-
Page 19: Lock Screw
Maintenance Table is rocked Unlock screw Lock bearing cover Lock ring End bearing cover lock screw... - Page 20 Grounding Welder Power source...
- Page 21 POS1 Structure Item Part No Part Name Q’TY P100A1 Table case group P100A2 Welding ground P1005 Motor cover P1007 Table shelf P1006 Angle fixed screw W5/16”handle P1008-4 202Copper seat cover...
- Page 22 POS1 Structure Item Part No Part Name Q’TY P1004 Table case P1003 Table P100A1-1 Table axis group P1002 Axis gear P1010 Switch seat TM1308 Fixed position switch P1011 Drive gear P1012 Motor flange Reducing gear box DC65W90V DC motor P1004-1 Table case cover...
- Page 23 POS1 Structure Item Part No Part Name Q’TY P1001-1 Main axial tube P1001-2 Main axial seat P1001-3 Axial seat P1001-4 Axial piece P1001-5 Lock ring...
- Page 24 POS1 Structure Item Part No Part Name Q’TY P1008-1 Welding ground P1008-2 Grounded carbon brush P1008-3 Grounding spring 8-8 Terminal M8*30 Hexagon socket head screw M6*25 Hexagon socket head screw 50-12 Terminal 50 square ground cable 50-10 Terminal M8 Washer M8 Spring washer...
- Page 25 circuit diagram 20131031 Inch Hold Welder COM-1100 AC 220V / 1Ø...