Advertisement
Quick Links
Advertisement
Related Manuals for Baton POS2CC10
Summary of Contents for Baton POS2CC10
- Page 1 20190920 OWNERS MANUAL POS2CC10...
-
Page 2: Chapter 1: Functon
Chapter 1: Functon... - Page 3 Page 1 POS2 Structure characteristic and Specification ●Carbon brush electric conduction, the copper alloy outer cover dispels the heat. ●Internal diameter 60mm. Pass through holes ●Air cooling, duty cycle 300A / 100% ●The table is electroplated, it is not apt to stick dregs. ●All right use of two sides of the table.
- Page 4 Page 2 1.2 POS2 Structure POS-2A Positioner Eccentric Load A : Eccentric Center (mm.) POS-2A Center of Gravity B :Center of Gravity (mm.) POS-2B Positioner Eccentric Load POS-2C Positioner Eccentric Load POS-2D Positioner Eccentric Load A : Eccentric Center (mm.) A : Eccentric Center (mm.) A : Eccentric Center (mm.) POS-2B Center of Gravity...
- Page 5 POS2 Size Page 3 ØA ØF POS1 POS2 340mm 340mm 375mm 418mm 276mm 319mm 206mm 206mm 220mm 220mm 10mm 10mm UNIT:mm...
- Page 6 Page 4 COM-1000 Finction Specification / No. COM-1000 Power A1: AC110V/60Hz/4A A2: AC220V/50Hz/3A FUSE Power of the motor DC90V/150W Rotate the direction cw/ccw COM-1000 Timer 0-240sec (Five kinds of adjustable time ranges) Arc way of the welde Standard Line welder Stop the brake Magnetism brake H.F.
- Page 7 Page 5 Structure characteristic ○Welding method that can be matched ●MIG/MAG ●TIG ●Wire-TIG ●Plasma weld ●SAW FUSE ○Dispose the place COM-1000 ●In the factory ○Duty cycle ●Can operate in succession100% ●Weld electric current 300A...
-
Page 8: Chapter 2: Installation
Chapter 2: Installation... - Page 9 Page 6 Installation Weld power source...
- Page 10 Page 7 2.2 Install the method of the drive motor Adj. move Permit to move 3 - 5mm. drive motor Rotate the table and confirm moving the distance(3 - 5 mm) with hands, lock the drive motor...
-
Page 11: Chapter 3: Operating
Chapter 3: Operating... - Page 12 Page 8 Control Panel FUSE COM-1000 1.Power switch 8.Welder switch 2.Power light 9.Auto / Inch switch 3.Table light 10.Timer 4.Welder light 11.Start switch socket(4P) 5.FUSE 12.Welder switch socket(3P) 6.Table speed (RPM) 13.Table motor socket(2P) 7.Table cw/ccw switch...
- Page 13 Page 9 Inch operating Standard Inch Link Start switch Power switch on Inch switch to down Welder switch to up Light Rotate speed ( RPM) Rotate the direction cw/ccw Table and welder off Table and welder on Light Stop switch Light...
- Page 14 Page 10 Timer operating Standard Timer Link Power switch on Welder switch to up Time switch to up Light Timer Rotate the direction cw/ccw Rotate speed ( RPM) Table and welder off Table and welder on Start switch Light Start timer End timer Light...
- Page 15 Page 11 Table start and accelerate time to adjust Accelerate time to increase ACCEL t(sec) Accelerate time to reduce ACCEL Open the control panel DC motor driver FUSE COM-1000...
- Page 16 Page 12 The time of the timer range adjusting Open the control panel FUSE COM-1000 8Sec 30Sec 60Sec 180Sec 240Sec...
- Page 17 Appendix...
- Page 18 Warn the item TIG Welder TIG Welder TIG Welder...
- Page 19 Maintenance Table is rocked Unlock screw Lock bearing cover Lock ring End bearing cover lock screw...
- Page 20 Grounding Welder Power source...
- Page 21 POS2 Structure Item Part No Part Name Q’TY P200A1 Table case group P200A2 Welding ground P2002 Motor cover P2001 Table shelf P1006 Angle fixed screw W5/16”handle P1008-4 202Copper seat cover...
- Page 22 POS2 Structure Item Part No Part Name Q’TY P1004 Table case P1003 Table P100A1-1 Table axis group P2003 Axis gear P1010 Switch seat TM1308 Fixed position switch P2004 Drive gear P1012 Motor flange Reducing gear box DC motor P1004-1 Table case cover...
- Page 23 LAMP3 5K ohm LAMP2 I F- F+ A- A+ L2 L1 FUSE1 OUT1 1M OHM LAMP1 FUSE1 P1:MAIN CONTROL BOARD SW2:WELDER LINK SWITCH P2:DC MOTOR DRIVER SW3:TIMER/MANUAL SWITCH (2P2S) T2:transformer(AC110V/220V TO AC12V) SW4:POWER SWITCH VR1:5Kohm RATATIONAL SPEED SW5:PEDAL SWITCH VR2:1M ohm TIMER SET LAMP1:POWER LAMP FUSE1:5A FUSE LAMP2:TURN TABLE OPERATES LAMP...