Related Manuals for Rustibus 32 ELECTRIC
Summary of Contents for Rustibus 32 ELECTRIC
- Page 1 OPERATION MANUAL 032-2000 RUSTIBUS® 32 ELECTRIC Single Phase 220 V - 240 V - 50/60 Hz...
-
Page 2: Declaration Of Conformity
Genuine Rustibus® parts only! Machine may vary from pictures DECLARATION OF CONFORMITY Manufacturer: Rustibus Worldwide AS Bekkjarviksundet 19 N-5397 BEKKJARVIK NORWAY The authorised representative In the EEA: Rustibus N.V. Noordersingel 7 B-2140 ANTWERP BELGIUM Hereby declares that the Products specified: Rustibus®... - Page 3 If they are not there, they’re not GENUINE PARTS. Use only the best, don’t settle for less. RUSTIBUS® If they are not there, they´re not genuine spares. Use only the best, don´t settle for less.
- Page 4 Genuine Rustibus® parts only! Machine may vary from pictures HELPFUL IDENTIFIERS In addition to information on installation and operation, this instruction manual may contain WARNINGS and CAUTIONS pertaining to user safety, and NOTES on important, useful operating guidelines. A WARNING indicates a potentially hazardous situation, which if not avoided, could result in death or serious injury.
- Page 5 If used over prolonged periods for vertical work, lifting assistance should be considered to prevent accidents, fatigue etc. Rustibus® de-scaling Tool should be properly maintained and stored when not in use to avoid damage to parts.
- Page 6 Machine may vary from pictures PLEASE READ THE WARNINGS BEFORE OPERATION WARNINGS: When connecting, changing, or repairing the Rustibus® 32, the power supply MUST ALWAYS be disconnected. IMPORTANT: Do not push down on your machine. This only damages the tool, it does not improve results.
- Page 7 This does not improve the result, it only damages the machine. • The Rustibus® 32 is equipped with a dead-man switch to ensure operator safety. Note that the machine will not be idle immediately. Allow the machine to come to a stop before putting down.
- Page 8 OPERATING THE RUSTIBUS® ANGLE DE-SCALER The Rustibus®32 is easy to operate and leaves the surface clean to St 3+++(SP11+++). The RPM of your Rustibus® 32 electric unit is adjustable. But for optimal results and to avoid excessive strain on the motor and/or damage on the chain drum, we recommend you set the speed control on level ‘E’...
- Page 9 Always disconnect the power supply before dismantling the Rustibus machine. WARNING When connecting, changing, or repairing the Rustibus angle de-scaler, the power supply must always be disconnected REPLACING THE CARBON BRUSHES (032-2132) 1) Open the Cover (032-2101) on both sides of the machine.
- Page 10 Genuine Rustibus® parts only! Machine may vary from pictures PARTS AND SPARES WHEN CONNECTING, CHANGING, OR REPAIRING THE RUSTIBUS® 32, THE POWER SUPPLY MUST ALWAYS BE DISCONNECTED. RUSTIBUS® 32 ELECTRIC 220V CONSUMABLES 032-2156: R32 Chain Drum 032-2202: R32 Wire Brush GENERAL OVERVIEW Rustibus®...
- Page 11 Genuine Rustibus® parts only! Machine may vary from pictures MOTOR PARTS - RUSTIBUS® 32 ELECTRIC 220V PARTS TO RUSTIBUS® 32 032-2004 R32 Connection Cable – 6M 032-2005 R32 Protecting Cable Cover 032-2006 R32 BOD Grease 032-2013 R32 I.D Plate 032-2061...
-
Page 13: Additional Features
The Rustibus® Magno Rollers are a magnetised wheelbase for the Rustibus® 30 Series. They use a powerful magnet to support the entire Rustibus® hand tool which makes them perfect for use on angled steel surfaces.The Rustibus® Magno Roller will enhance safety and operator comfort. - Page 14 Rustibus cannot be held liable for any damages (to Rustibus® machines or personnel) as a result of use of non genuine parts. We reserve the right to refuse any claims on parts or Rustibus® machinery unless it can be proven that genuine parts only have been used on Rustibus® machines.
-
Page 15: Contact Information
Genuine Rustibus® parts only! Machine may vary from pictures CONTACT INFORMATION NORWAY: Rustibus Worldwide AS Bekkjarviksundet 19 NO - 5397 Bekkjarvik Norway Tel: + 47 95 96 70 02 E-mail: bergen@rustibus.com ANTWERP: Rustibus N.V. Noordersingel 7 2140 Antwerpen Belgium Tel: + 32 3227 2096 Fax: + 32 3227 2097 E-mail: antwerp@rustibus.com... - Page 16 “WALK BEHIND”SERIES * DESIGNED TO DE-SCALE AND POWER BRUSH SHIP DECKS, HATCH COVERS, TANK TOPS, ETC. * THE ORIGINAL RUSTIBUS® CHAIN DRUM SYSTEM * RESULT: St 3 +++ (SSPC-SP11 +++) NEW 2019 ! Rustibus® 1600 * ELECTRIC (THREE-/SINGLE PHASE), PNEUMATIC...
-
Page 17: Vertical System
* MOST EFFICIENT HAND TOOL ON THE MARKET * IDEAL FOR DAILY MAINTENANCE ON DECK, AVAILABLE SPOT SCALING, CARGO HOLD AND BALLAST AS EX MODEL TANK DE-SCALING. * THE ORIGINAL RUSTIBUS® CHAIN DRUM SYSTEM Rustibus® 32 Electric 220V Rustibus® 33 Air Rustibus®...
Need help?
Do you have a question about the 32 ELECTRIC and is the answer not in the manual?
Questions and answers