GEIGER INline GSI56 Series Original Assembly And Operating Instructions
With electronic end stop for the facade technology
Hide thumbs
Also See for INline GSI56 Series:
- Original assembly and operating instructions (56 pages)
Table of Contents
Advertisement
Quick Links
GEIGER System INline GSI56.. E12 SMI
with electronic end stop for the facade technology
Original-Montage- und
DE
Betriebsanleitung
Original assembly and
EN
operating instructions
Notice originale de montage
FR
et d'utilisation
Instrucciones originales de
ES
instalación y funcionamiento
Istruzioni originali di installazione
IT
e funzionamento
www.geiger.de
EN
1
EN
Advertisement
Table of Contents
Related Manuals for GEIGER INline GSI56 Series
Summary of Contents for GEIGER INline GSI56 Series
- Page 1 GEIGER System INline GSI56.. E12 SMI with electronic end stop for the facade technology Original-Montage- und Betriebsanleitung Original assembly and operating instructions Notice originale de montage et d’utilisation Instrucciones originales de instalación y funcionamiento Istruzioni originali di installazione e funzionamento...
-
Page 2: Table Of Contents
1. General information Dear customer, By purchasing a GEIGER motor you have decided on a quality product from GEIGER. Thank you very much for your decision and the confidence placed in us. Before you put this drive into operation please observe the following safety instructions. It serves for the prevention of danger and for the avoidance of personal injury and damage to property. -
Page 3: Intended Use
GJ 56 Design options Torque in Nm Motor diameter GEIGER INline System 4. Safety instructions ATTENTION: Important safety instructions. For personal safety, it is important to follow these instructions. Please keep these instructions for future reference. f Do not allow children to play with stationary controls. Keep remote controls away from children. -
Page 4: Safety Instructions For Assembly
A plug for the disconnection of the motor from the power supply must be accessible after installation. f Damaged connecting cables must be replaced by GEIGER connecting cables of the same type. f The device must be mounted as described in the installation instructions. Fixations shall not be made with adhesives since they are regarded as unreliable. -
Page 5: Assembly Instructions
The system components supplied by GEIGER may not be repro- cessed or altered, otherwise the warranty expires. Before installation, the motor and the other system parts should be checked for visible damage. -
Page 6: Identification Number
• In order to prevent a malfunction caused by coupling, the supply line (ref. NYM) from the actuator/switch to the motor must not exceed 100m in case of motors with electronic end stops. Gerhard Geiger GmbH & Co. KG | 100W2507 V001 0220... -
Page 7: Conductor Assignment For Smi Drives For Mains Voltage
It is not permitted to lay SMI wires together with wires carrying other signals in one cable. If SMI drives wired in parallel are supplied with electrical power from different phases, the SMI I+ and I- wires must be laid in a separate cable. www.geiger.de... -
Page 8: Smi Drives On Different Ac Phases
N L2 N L3 Drive Drive Drive permitted Push button operation with power supply from different phases Drive Drive Drive permitted Push button operation with power supply from one phase Gerhard Geiger GmbH & Co. KG | 100W2507 V001 0220... -
Page 9: For Your Notes
11. For your notes … SMI-KEY-ID (sticker) Place of installation e.g.: 1 floor, left side, third room, 1 window etc. www.geiger.de... -
Page 10: Setting Of The End Stops
Press programming key for about UP/DOWN keys simultaneously until, after about 3 seconds, PROG 3 seconds the motor confirms “end position programming activated” with 1 x click-clack. Then release the key. Gerhard Geiger GmbH & Co. KG | 100W2507 V001 0220... -
Page 11: Programming/Changing The End Stops
Readjust the end positions, if necessary. After running several times, • The motor became too hot and has the motor breaks down and switched off. no longer responds. Try it again after a cooling time of about 15 min. www.geiger.de... -
Page 12: Declaration Of Conformity
Gerhard Geiger GmbH & Co. KG Schleifmühle 6 | D-74321 Bietigheim-Bissingen Phone +49 (0) 7142 9380 | Fax +49 (0) 7142 938 230 | info@geiger.de | www.geiger.de Sitz Bietigheim-Bissingen | Amtsgericht Stuttgart HRA 300591 | USt-IdNr. DE145002146 Komplementär: Geiger Verwaltungs-GmbH | Sitz Bietigheim-Bissingen | Amtsgericht Stuttgart HRB 300481 Geschäftsführer: Roland Kraus | WEEE-Reg.-Nr. -
Page 13: Maintenance
With angel gear GSI1…: total length + 52 mm / weight + 0,4 kg Subject to technical modifications. Please find information to the ambient temperature range of our GEIGER motors under www.geiger.de 21. Notes on waste disposal Recycling of packaging materials In the interest of environmental protection, please contact your local government’s recycling or... - Page 14 Gerhard Geiger GmbH & Co. KG | 100W2507 V001 0220...
- Page 15 www.geiger.de...
- Page 16 They will be happy to assist you. Gerhard Geiger GmbH & Co. KG Schleifmühle 6 | D-74321 Bietigheim-Bissingen T +49 (0) 7142 9380 | F +49 (0) 7142 938 230 info@geiger.de | www.geiger.de Gerhard Geiger GmbH & Co. KG | 100W2507 V001 0220...