Advertisement

4
Instructions For Use
(Please keep and read this manual carefully before using this product)
W PRO
support@aovotoys.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the W PRO and is the answer not in the manual?

Questions and answers

Summary of Contents for Aovo W PRO

  • Page 1 Instructions For Use (Please keep and read this manual carefully before using this product) W PRO support@aovotoys.com...
  • Page 2: Disclaimer & Warning

    . You agree to use this product only for purposes that are proper and in accordance with local regulations, terms and all applicable polices and guidelines AOVO may make available. 2. When using this product, please be sure to strictly abide by the specifica- tion requirements and safety guidelines stated in this document.
  • Page 3: Flight Environment

    ④ Please do a thorough check of the product before each use. Inspect the integrity of the parts, any signs of cracks and wear of the propeller, battery power and effectiveness of the indicator, etc. If after doing a complete check any issues are found, please refrain from using the product until the issue has been resolved.
  • Page 4: Operation Requirements

    Operation Requirements: ① Please don’t use this product to follow any moving vehicles . ② During the flight, only turn off the motor in case of an emergency. ③ As battery becomes low return the drone back to your starting point. ④...
  • Page 5 ⑦ It is recommended to only use the USB charging cable that comes with the drone to charge the battery. ⑧ Don't connect the battery directly to wall outlets or car cigarette -lighter sockets. ⑨ Don't attempt to disassemble or modify the battery in any way. ⑩...
  • Page 6: Maintenance

    MAINTENANCE ① Clean the product after each use with a clean, soft cloth. ② Avoid prolonged exposure to direct sunlight and avoid buildup of heat on the drone. ③ This device is not waterproof and must not be submerged in water under any circumstance.
  • Page 7 DRONE’S DETAILS Propeller A Battery Propeller B Propeller B Power Switch HD Camera Propeller A Vision Positioning Lens Lights -06-...
  • Page 8: Transmitter Details

    TRANSMITTER DETAILS Transmitter Functions Antenna Gyroscope calibration Speed Left Joystick Right Joystick Unlock Return to Home Phone Holder - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Record Video Camera Angle Adjustment...
  • Page 9 •GPS Mode Switch When turning on the transmitter, the default mode is the GPS Mode. Turn off GPS by press GPS switch. Check the icon “ ” on the App interface to confirms GPS status. •Return to Home Press the button to start the RTH, the transmitter makes “beep beep” sound per 1.5 seconds and the drone will fly back to the recorded Home Point.
  • Page 10: Controller Operation

    Controller Operation Left Joystick Ascend Descend Down Right Left Rotate Right Rotate Left Right Joystick Forward Down Backward Left Right Fly to Fly to Left Right -09-...
  • Page 11: Installation

    INSTALLATION Drone Battery Installation: Push the battery into the battery compartment of the drone. Make sure that you hear a click sound indicating the battery is firmly installed. Attention: The battery should be installed firmly, failure to do so may affect the flight safety of your drone.
  • Page 12: Install Tf Card

    Install TF Card As shown in the above figure. Please push the camera module out and insert the TF card ( Need to be purchased separately ) to TF card slot, then you could hear “Click” , means insert successfully. Push the camera module into the specified position of drone.
  • Page 13 Propellers Installation HEAD The drone will not fly unless the correct propeller is installed on the correct motor shaft. See illustration above. An “A” “B” is printed on the back of each propeller. Lock the propeller to the motor shafts with screws rotating each screw clockwise.
  • Page 14: Phone Holder

    Phone Holder ① Pull down the position of controller. ② Adjust the Mobile Device Holder to hold tightly for the mobile device. -13-...
  • Page 15 CHARGING USB Adapter (5V/2.0A) ① Connect the USB cable to a USB socket such as mobile power supply (Use an power supply with standard output voltage 5V and current greater than or equal to 2A). And then connect the battery with USB cable, the LED of battery is flashing, means charging.
  • Page 16: Download App

    OPERATION GUIDE Download APP Android APP on Google play Scan the QR code, corresponding to either App Store™ or Google™ Play Store and download the “ W - GPS ” application for free. Required Operating Systems: iOS v8.0 and later / Android v4.3 and later Unfolding the Drone HEAD To unfold the drone follow the steps below.
  • Page 17 Check the drone’s status in the ”W - GPS” App. ② Your smartphone will launch a search of the available Wi-Fi networks: W PRO-4K-****** ③ Select the Wi-Fi network: PRO-4K-******. ④ Wait for several seconds until your smartphone connect to the Wi-Fi network of the drone.
  • Page 18: Calibrating The Compass

    Pairing After connect the WiFi signal between smart phone and drone. Turn on the switch on the transmitter. Once the transmitter sends out “Beep” sound, it means that the drone has been successfully paired with the transmitter. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Calibrating the Compass After pairing operation, the LED lights of the drone are sharp-flashing, that mean is begin compass calibration.
  • Page 19: Gyroscope Calibration

    Front lights flash slowly Solid Rear lights Step 2: Now, the APP interface displays the diagram. Hold the drone vertically and rotate the drone in 3 complete circles. When completed the transmitter sends out “Beep” sound and LEDs lights of drone turn solid. Attention: ・If the GPS receives a signal from 7 or more satellites the rear LEDs of the drone will flash twice per second.
  • Page 20 Unlocking the Motor Please unlock the motor before take-off. Press the red button “ ” , the motors rotate. ① Unlock the motor function will be activated, base the GPS receives a signal from 7 or more satellites OR Indoor mode. ②...
  • Page 21: Function Details

    One Key Takeoff/ Landing ① ② Landing Take-off ① After unlocking the drone, press the “ ” button in the APP interface, then “ ” and the drone will automatically take off Slide right to confirm and hover at 1.5m altitude. Or press the button “ ”...
  • Page 22: Return To Home (Rth)

    Return to Home (RTH) ・The Return to Home function brings the drone back to the Home Point. ・The Home Point is the location at which the drone takes off. This location will be recorded as the Home Point. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Smart RTH If the GPS signal is available (7 or more satellites reception)
  • Page 23 Low Voltage RTH ① When the drone's lights flash slowly, the “ ” symbol is displayed on the APP interface, the First Low Voltage RTH will be triggered. The transmitter will emit a “Beep, Beep, Beep” alert every 5 seconds. The drone will return automatically in the following two conditions: (At this time, the drone can only fly within a safe range of the height no more than 20m and the distance...
  • Page 24 ② If the drone’s lights begin to flash rapidly the “ “ symbol will be displayed on the APP interface and the transmitter will emit a “Beep..., Beep...” alert. The Second Low Voltage RTH is automatically triggered. Now, the drone will return automatically and compulsively. a.
  • Page 25 Image Positioning System ① The Image Positioning System consists of a camera ① module, which acquires the position information of the drone through visual images to ensure precise positioning and safe flight of the drone. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - The Image Positioning System is typically used in indoor environment and the altitude lower than 8m.
  • Page 26 1. Fly fast at an altitude below 0.5m. 2. Fly over monochrome surfaces (like pure black, pure red, pure red and pure green). 3. Fly over strong light reflective surfaces or surfaces prone to reflection. 4. Fly over water or transparent object surfaces. 5.
  • Page 27: Operation Interface

    APP OPERATION INSTRUCTION Operation Interface VIEW CAMERA Follow Surrounding 180° Screen 3D VR Waypoint Rotation flight Home Find Gesture to Lock Music page take pictures drone GPS Signal Setting Flying Drone Battery record signal Take off Return Function Photo Shutter Video button H: N/A...
  • Page 28: Setting Parameters

    Setting Parameters Click the “ ” icon to enter the setting interface (as shown in the figure above), you can set a limited flight range: 1. Maximum flight distance: 60~3300 feet / 20~1000 m. 2. Maximum flight altitude: 60~390 feet / 20~120 m. 3.
  • Page 29 Follow Me When the Follow Me function is enabled, the drone will follow the GPS in your smart phone to follow you wherever you go. 1. Ensure the drone's flight range is within 30m. 2. Click the“ ” icon on the App interface, and click “ ”...
  • Page 30: Waypoint Flight

    Waypoint flight It is recommended to enlarge the map if you want to use Waypoint flight. 1. Click the“ ” icon on the app interface, then click " " to enter the Waypoint flight function. 2. Draw a line on the map to create a path (Max 15 paths), click “ ”...
  • Page 31: Point Of Interest

    Point of Interest 1. Click the“ ” icon on the App interface, and click “ ” then “ ”to enter the Point of Interest function. Slide right to confirm 2. The drone will record it’s flight position the moment you enter this function as the point of interest.
  • Page 32 Take Photo/ Video 1. Click the “ ” icon to switch between photo and video mode. 2. When the shutter button is “ ”, click once to take a photo. 3. When the shutter button is “ ”, click once to start recording, and click again to stop recording.
  • Page 33 DRONE STATUS INDICATOR Indicator Status Indicator Status Meanings The drone is connected to the transmitter The LED lights of the drone are flash rapidly and begin Compass Horizontal Calibration. Compass Horizontal Calibration has completed and begin Compass Vertically The LED lights of drone are flash slowly. Calibration.
  • Page 34: Specifications

    SPECIFICATIONS DRONE Model: W PRO Weight: 520 g / 18.4 oz Max Flight Time: Approx 30 minutes Operating Temperature Range: 32° to 104°F Dimensions: 115 x 175 x 80 mm (Folded) 285 x 225 x 80 mm (Unfolded) DRONE BATTERY Capacity: 2500 mAh Voltage: 11.4 V...
  • Page 35 CAMERA Camera frequency: 5 GHz Video/ Photo Resolution: 4K Lens: FOV 90° FPV Distance: 800m (outdoor and unobstructed) Photo: JPEG Video: MP4 MAX Supported TF Cards: 64 GB (Not included) Controllable Range: Pitch: -90° to 0° Operating Temperature Range: 32° to 104°F USB CHARGING CABLE Voltage: 5 V Ampere: >...
  • Page 36: Troubleshooting

    TROUBLE SHOOTING Problem Solution The drone is in the gyroscope When the drone is powered on, calibration state. Please place the indicator light keeps flashing the drone on an flat and level rapidly. surface. Place the drone on a flat, level The drone cannot hover after surface and repeat the gyro takeoff and tilts to one side.
  • Page 37 BATTERY WARNING: 1. Failure to follow all the instructions may result in serious injury, irreparable damage to the battery and may cause a fire, smoke or explosion. 2. Always check the battery’s condition before charging or using it. 3. Replace the battery if it has been dropped, or in case of odor, overheat- ing, discolouration, deformation or leakage.
  • Page 38 11. Non-rechargeable batteries are not to be recharged. Rechargeable batteries are only to be charged under adult supervision. 12. Different types of batteries or new and used batteries are not to be mixed. 13. Batteries are to be inserted with the correct polarity. 14.

Table of Contents

Save PDF