Table of Contents
Advertisement
1
2
3
DISC
DISC
DISC
YMERSION
B.BOOST
MUSIC
MODE
DOLBY NR
REC/PAUSE
5
1
2
1
2
6
7
6
7
A
B
TIME
TIME
PROG
MODE
REPEAT
DISC SKIP
3
TUNER
REC/PAUSE
4
POWER
SLEEP
/I
Display information during programming
Display information during programming
TRACK
VCD PBC
NR
TUNER
TIMER
CD
M
SLEEP
MD
HALL
NOR TEST
TAPE
MERSION
PHANTOM
Next play order
Selected track
Total remaining time on
number
this side of the tape
TRACK
REM
NR
CD
M
Programmed track numbers light up
and only programmable track numbers
among unprogrammed ones flash.
DISC CHANGE
OPEN / CLOSE
PRESET/ TUNING/ BAND
A/B/C/D/E
VOLUME
DOWN
UP
1
INPUT
INPUT
RANDOM
REPEAT
TIME
TIME
HOUR
MIN
AUTO/MANUAL
MEMORY
DISPLAY
TIMER
TIME ADJ
STANDBY/ON
3
4
5
3
4
5
8
PRESET
8
9
0
C
D
E
+
R. TIME
EDIT
I0
RANDOM
TUNER
9
CD
7
TAPE
DIRECTION
YMERSION BASS BOOST
MUSIC
INPUT
VOLUME
1
Selected disc
RANDOM
1 2 3 4
5
6
EDIT
S F REP
7 8 9 10
11
12
A
B
PROG
VOLUME
13 14 15
OVER 15
Side of the tape
1 2 3 4
5
6
7 8 9 10
11
12
A
PROG
VOLUME
13 14 15
OVER 15
Manual EDIT recording
You can program tracks manually while watching the
remaining time on both sides of the tape.
1
Press INPUT
or
once or more until "CD" (
appears on the display, and load a disc (or discs) on the
disc tray.
2
Follow steps 3–5 on page 23.
3
Press PROG.
* "PROG" and "P-01" will light up on the display, and all
track numbers on the selected disc will begin flashing.
4
If necessary, select the desired disc by pressing DISC
SKIP.
5
Select the desired track number by pressing the numeric
buttons.
6
Repeat steps 4 and 5 to program more selections for side A
of the tape. You can select the same track again.
* Pressing TIME displays the total remaining time on side
A of the tape for about 1 second, and then it is replaced
by the display of the next play order.
* If "TM OVER" appears on the display, the track number
just selected cannot be programmed because there is
not enough time remaining on side A of the tape.
However, at this time, if any other track number is
flashing continuously on the display, you can program it
instead of the unprogrammable one.
7
When the programming for side A is finished, press
R. TIME.
* "Side–B" appears on the display. You can begin
programming for side B.
* After following this step, you can check the programmed
contents for side A and side B alternately by pressing
R. TIME at any time before you press EDIT in step 9.
* The tape side indicator (
side currently selected.
8
Repeat steps 4 and 5 to program selections for side B of
the tape. You can select the same track again.
9
8
Press EDIT. ("EDIT" (
) lights up on the display.)
The recording starts.
Notes on recording with the EDIT function
● To check, cancel or correct program data, refer to page 11.
● The maximum number of tracks that can be programmed is
20.
● The track number 16 or higher cannot be programmed by
this function.
Recording
1
5
,
9
) shows the programming
)
E-25
Hide quick links:
Advertisement
Table of Contents
