Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Electro-Air EA-13000
Summary of Contents for Electro-Air EA-13000
- Page 1 EA-13000 Installation Manual Ignition/Starter Switch Panel Electroair Acquisition Corp. 5097 Williams Lake Road Waterford, MI 48329 U.S.A. Phone: 248-674-3433 Fax: 248-674-4231 Email: sales@electroair.net Electroair Acquisition Corp. IM EA-13000 Page 1 of 10 Revision 03 Prepared by: EAC 02/04/2020...
-
Page 2: Table Of Contents
Table of Contents REVISION LOG ......................2 OVERVIEW OF IGNITION/STARTER SWITCH PANEL INSTALLATION ..... 3 EA-13000 KIT DESCRIPTION & REQUIREMENTS ............4 EA-13000 KIT CONTENTS ..................... 4 RECEIVING AND ACCEPTANCE CHECKING OF EIS KIT .......... 4 PRECAUTIONARY STATEMENTS: ................5 INSTALLATION OF EA-13000: .................. -
Page 3: Overview Of Ignition/Starter Switch Panel Installation
This manual will cover the following general installation steps: 1. General overview and recommendations 2. Removal of old ignition components 3. Set-up & installation of p/n: EA-13000 Ignition/Starter Switch Panel 4. Final installation steps Electroair strongly recommends reading through this entire installation procedure before installing the Electroair Ignition/Starter Switch Panel for your Electroair electronic ignition system equipped aircraft. -
Page 4: Ea-13000 Kit Description & Requirements
1. This kit replaces the rotary key switch on aircraft with an EIS kit installed. 2. 12V or 24V electrical system capable of 0.75A. Other items needed: 1. Basic tools and standard aircraft hardware required for mounting EA-13000 Ignition/Starter Switch Panel. 2. Electrical tools for cutting, stripping, and terminating various wiring. Also recommended is a good selection of cable ties for harness routing and tie-off, and a selection of shrink tubing for covering exposed electrical connections. -
Page 5: Precautionary Statements
POH to have MAG switch in OFF position during starting. Consult with appropriate licensed mechanic. Consult applicable service manuals for the aircraft. Electroair Acquisition Corp. IM EA-13000 Page 5 of 10 Revision 03 Prepared by: EAC 02/04/2020... -
Page 6: Installation Of Ea-13000
Installation of EA-13000: 1. General Overview and Recommendations: Determine the proper location for the panel. Determine the most appropriate mounting method. Overall dimensions are provided in Figure 1 and Figure 2. Cutout dimensions are provided in Figure 3 and Figure 4. All dimensions are in inches. -
Page 7: Figure 3: Configuration A Cutout Dimensions
If the ignition/starter switch panel is not being installed in the rotary key switch location, plug the hole left by removing the rotary key switch as necessary. 3. Set-up & Installation of p/n: EA-13000 Ignition/Starter Switch Panel: Review the leads corresponding to the location of the ignition/starter switch panel. -
Page 8: Figure 4: Configuration B Cutout Dimensions
Insulate any exposed electrical connections in accordance with 43.13-1B Change 1 section 11-159. Insert ignition/starter switch panel into instrument panel and screw down using standard hardware. Electroair Acquisition Corp. IM EA-13000 Page 8 of 10 Revision 03 Prepared by: EAC 02/04/2020... -
Page 9: Figure 5: Configuration A And B Back Surfaces
Repeat the start-up process. If the aircraft fails a second time, contact the factory for support. (248-674-3433 or sales@electroair.net) Electroair Acquisition Corp. IM EA-13000 Page 9 of 10 Revision 03 Prepared by: EAC 02/04/2020... -
Page 10: Glossary And Abbreviations
Must/Shall – a mandatory requirement RPM – Revolutions per Minute POH – Pilot’s Operating Handbook STC – Supplemental Type Certificate TDC – Top Dead Center Electroair Acquisition Corp. IM EA-13000 Page 10 of 10 Revision 03 Prepared by: EAC 02/04/2020...
Need help?
Do you have a question about the EA-13000 and is the answer not in the manual?
Questions and answers