Advertisement
1.3.
BATTERY SAFETY PRECAUTIONS
WARNING! Battery contains Lithium-ion which is dangerous. Handle with care to avoid damage, fire, corrosion or personal injury.
‰
Charge battery prior to its first use. The battery will have been shipped in a low charge state to reduce the risk of burns or fire.
9
DO NOT Attempt to open, disassemble, modify or service the battery pack.
8
DO NOT Crush, puncture, short external contacts or dispose of in fire or water.
8
DO NOT Expose to temperatures above 40°C (104°F).
8
Replace only with the battery pack designated for this product.
9
Use only the supplied charging base provided to charge the battery.
9
DO NOT attempt recharging the battery by means of an engine generator or a DC power source.
8
WARNING! Dispose of spent batteries correctly as they contain Lithium-ion. DANGER! DO NOT attempt to disassemble the
‰
battery. For safety and environmental reasons DO NOT discard in domestic waste or by burning. ONLY discard or recycle
according to local authority regulations.
WARNING! DO NOT allow a leaking battery to contact your person.
‰
1.4.
GENERAL SAFETY
Maintain the Power Ratchet Wrench and battery in good condition. Check moving parts alignment on a regular basis.
9
Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
9
dangerous and will invalidate the warranty.
Ensure the Ratchet Wrench is switched off before installing the battery pack.
9
Keep the Ratchet Wrench and charger clean for best and safest performance.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Evaluate your working area before using the Ratchet Wrench; e.g. ceilings, floors and enclosures may contain electrical items or
9
water piping.
Ensure battery pack is correctly inserted into the Ratchet Wrench handle and latched in place before attempting to switch on
9
Ratchet Wrench.
Secure loose work pieces with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Wear approved safety eye protection (standard spectacles are not adequate).
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.
9
Keep children and unauthorised persons away from the working area.
9
DO NOT use the Ratchet Wrench where there are flammable liquids, solids or gases, such as paint solvents, etc.
8
DO NOT allow children to operate the Ratchet Wrench.
8
DO NOT operate the Ratchet Wrench if any parts are missing as this may cause failure and/or personal injury.
8
DO NOT hold unsecured work piece in your hand.
8
DO NOT leave the Ratchet Wrench operating unattended.
8
DO NOT carry the Ratchet Wrench with your finger on the power switch. Keep switch lock in the locked position.
8
DO NOT use the Ratchet Wrench for a task it is not designed to perform.
8
DO NOT operate the Ratchet Wrench when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT get the Ratchet Wrench or battery charger wet or use in damp or wet locations.
8
2. INTRODUCTION
The Sealey Power Speed Ratchet combines the high torque of a traditional hand ratchet with the faster efficiency of an electric power tool,
providing working speeds 10-20 times quicker when tightening/loosening fasteners. No load speed 200rpm saving the time and fatigue of
a traditional hand ratchet wrench. The clutch mechanism is designed so that when the maximum torque is reached (1Nm/0.74ft/lb) a tactile
vibration indicates to change over to manual mode for continued tightening or loosening of fasteners. Includes a rechargeable lithium-ion
battery, full recharge in just 45 minutes and is fully protected from over-charge, over-discharge or over-heating. Ultra smooth 60-tooth ratchet
action, twist-reverse and quick release with spring-ball socket retention, power button with LED indicator and locking switch. Fitted with a
contoured, soft grip handle. Supplied with AC adaptor, charging base and storage case.
3. SPECIFICATION
Model No: ............................SPR001........................SPR002
Drive: ...................................... 3/8"Sq..........................1/2"Sq
Overall Length:...................... 295mm.........................315mm
Battery (SPR001B): . ...3.6V 2000mAh Li-ion.........3.6V 2000mAh Li-ion
Charging base:.................... S PR001C......................SPR001C
4. OPERATION
WARNING: Remove battery before maintenance is carried out.
‰
NOTE: When new, the batteries may have been shipped in a low charge state. Fully charge the batteries before using your tool.
4.1.
Ensure that you have read, understood and comply with all the safety instructions in Section 1.
4.2.
BATTERY CHARGER
4.2.1.
To remove the battery from the equipment, depress the spring loaded tabs on the sides of the battery. Remove the battery by
sliding it out. DO NOT touch the battery terminals.
4.2.2.
The battery is designed to fit into the charger one way only. Insert the battery fully and firmly to seat the battery into the charging
base.
4.2.3.
Take the base charger and plug it into the mains, switch on the power and the red LED on the charger will illuminate.
4.2.4.
The battery has 3 LED charge level indicators that show full or partial charges levels.
4.2.5.
When the battery is on charge the red LED on the charger will flash intermittently.
4.2.6.
When the green LED on the charger illuminates permanently the battery is fully charged.
4.2.7.
When both green and red LEDs flash the battery is not charging. Replace battery.
4.2.8.
Remove the battery from the charger. Switch off and remove the plug from the mains.
4.2.9.
Relocate battery into tool ensuring correct alignment. DO NOT force the battery in.
© Jack Sealey Limited
Original Language Version
SPR001, SPR002 Issue 2 (2,3) 04/03/20
Advertisement
