1. Manuals
  2. Brands
  3. LaserPerformance Manuals
  4. Boat
  5. LASER 2000
  6. Rigging manual

LaserPerformance LASER 2000 Rigging Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
LASER 2000
Rigging Manual
1.
Glossary
2.
Sail Number Positioning
3.
Rigging and raising the mast
4.
Rigging the Trapeze
5.
Boom and Gnav
6.
Jib
7.
Gennaker
8.
Mainsail
9.
Outhaul
10.
Cunningham
Reefi ng the Mainsail
11.
12.
Rudder
13.
Launching
14.
Laser 2000 Capsize Technique
15.
Maintenance and Service
16.
Cordage Lengths
LASER 2000

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LASER 2000 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for LaserPerformance LASER 2000

Summary of Contents for LaserPerformance LASER 2000

  • Page 1 LASER 2000 LASER 2000 Rigging Manual Glossary Sail Number Positioning Rigging and raising the mast Rigging the Trapeze Boom and Gnav Gennaker Mainsail Outhaul Cunningham Reefi ng the Mainsail Rudder Launching Laser 2000 Capsize Technique Maintenance and Service Cordage Lengths...

  • Page 2: Laser 2000 Rigging Instructions

    MAST Important information LEACH Th ere are three hatches and one transom drain bung on the Laser 2000. Every time you sail, these must be checked to ensure they are closed tightly and fi t correctly. BATTENS LUFF MAINSAIL 1.

  • Page 3: Rigging And Raising The Mast

    PRIMARY 3. If applicable, fi t trapeze wires in the top “T” terminal position on the mast. (Please note: Th e Laser 2000 trapeze kit is optional and is Attachment of Spreader. not supplied as standard) (fi gure 6) Primary Pin: 4.

  • Page 4: Rigging The Trapeze

    4. Rigging the Trapeze 12. Grip tape should be applied parallel to the gunwale edge commencing approximately Please note: Th e Laser 2000 trapeze kit is optional and is 200 mm in front of the shroud anchor points not supplied as standard.
  • Page 5 4. Fasten the head of the jib to the swivel 7. Gennaker using the clevis pin and split ring. (Tape up 1. Ensure the end of the gennaker halyard the shackle, pins and split ring to prevent taken from the base of the mast is free of knots snagging or damage to other sails and lines and tangles.
  • Page 6 11. Identify the clew patch, (written on the 5. Take the main halyard: sail) attach the center of the gennaker sheet to a. Ensure there are no twists in the halyard the clew of the gennaker. (As per jib sheet to and it is clear of the spreaders.

  • Page 7: Reefi Ng The Mainsail

    6. Feed the original, lower clew outhaul slug SLUG slide in to the boom cut out fi rst, followed by Th e use of a LaserPerformance supplied Laser 2000 mast head fl oat is highly advisable. fi gure 63 fi gure 64 the higher reefi...

  • Page 8: Cordage Lengths

    • All our GRP products are designed to be dry sailed. In other words stored on dry land. If you intend to leave your boat on a mooring for any length of time it is essential that you apply an osmosis barrier coat. LaserPerformance can recommend a suitable product.

  • Page 9: Owner Information

    Th is instruction manual is not a guide to sailing your craft and it should not be considered suitable for the task of learning to sail a boat. Please read the manual before rigging and sailing your Laser 2000. hull identifi cation number Before You Go Sailing: 1.
  • Page 10 Laser, SB3, Sunfi sh, and Dart PO Box 38442 are trademarks used under license. Dubai, UAE LaserPerformance reserves the right to make +971 (4) 885 7601 design and/or specifi cation changes to any of their products as part of their continuous development program.

Table of Contents