2. Safety ..................... 6 3. Box Contents ................12 4. Safety During Assembly ............13 5. Indentify Your Bed ..............14 6. Assembly: Standard Variant ............16 7. Assembly: Lite Variant ..............18 8. Operation via the App ...............20 9. Additional Information ..............23 SILVERsensor Manual...
About SILVERsensor Thank you for choosing SILVERsensor by LOGICDATA. With SILVERsensor, every effort has been made to ensure your comfort and safety. This Manual is intended to enable persons to assemble and operate the product safely. However, incorrect installation of the product, or usage outside of the intended use described in this Manual may lead to hazardous situations.
Page 4
• Improper product use • Disregard of the documentation • Unauthorized product alterations • Improper work on and with SILVERsensor or the Bed Frame • Operation of damaged products • Improperly performed repairs • Unauthorized changes to the operating parameters •...
Page 5
This Class B digital apparatus complies with Canadian ICES-003. FCC Compliance The Radio Frequency for this product is 2.4 GHz The SILVERsensor by LOGICDATA complies with FCC CFR 47 Part 15 Subpart B/C. Operation is subject to the following conditions: The product may not cause harmful interference...
2. Safety IMPORTANT SAFETY INSTRUCTIONS About this Document This Manual is intended to help users safely install the SILVERsensor by LOGICDATA. It also contains instructions for operating the Bed Frame to which the SILVERsensor is connected using a mobile App.
Page 7
CAUTION which, if not avoided, could result in minor or moderate injury. signal word NOTICE indicates a situation that will NOTICE not lead to personal injury, but could lead to damage to the product or the environment. SILVERsensor Manual...
Page 8
• To disconnect the Bed Frame, turn all controls to the off position, then remove plug from outlet. • WARNING: Risk of injury – keep children away from the extended foot support (or other similar parts). SILVERsensor Manual...
Page 9
WARNING on the Bed Frame may lead to death or serious injury. • Do not convert or modify the Adjustable Bed Frame • Never open electrical components SILVERsensor Manual...
Page 10
Moderate risk of death or serious injury in explosive atmospheres Operating the SILVERsensor in potentially explosive atmo- spheres may lead to death or serious injury through explo- WARNING sions. • Read the relevant directives to determine whether an atmosphere is potentially explosive •...
Page 11
WARNING • Activate the Child Lock or lock you mobile device when children are present • Keep children away from moving Platforms • Do not allow children to play with the Bed Frame SAVE THESE INSTRUCTIONS SILVERsensor Manual...
3. Box Contents The SILVERsensor is delivered in a single package. The contents of this package are listed here. If you are missing parts, or if parts are damaged, contact LOGICDATA (see contact information, page 4.) You will require a screwdriver (cross-head) to complete assembly.
4. Safety During Assembly Moderate risk of death children and animals The plastic packaging of the SILVERsensor is a potential suffocation hazard. Leaving children or animals unsupervised WARNING with empty packaging may lead to death through suffocation. • Do not leave children or animals unsupervised •...
• Has Plug Ports in the Side Rails of the Frame You require this cable: Go to Chapter 6 on Page 16 for Assembly Instructions NOTE: For Queen and Twin XL Frames, mount the Cable clamp halfway between the Side Rail and SILVERsensor to hold slack. SILVERsensor Manual...
Page 15
Lite Frame Your Frame: • Has 5 Platforms • Has a Control Box (in a net under the center platform) You require this cable: Go to Chapter 7 on Page 18 for Assembly Instructions SILVERsensor Manual...
A. Mounting position, no massage motor. B. Mounting position, with massage motor 1. Attach all 4 Damping Elements next to the holes (marked) 2. Find and mark the position of the SILVERsensor on the Platform 3. Screw in the SILVERsensor Mounting Screws with a screwdriver 4.
Page 17
2. Connect the SILVERsensor Cable to the SILVERsensor. INFO If your Bed has an Underbed Light: Connect the Underbed Light Cable to the SILVERsensor Cable. 3. Plug the SILVERsensor cable into the empty Side Rail Port 8 pin 2 pin 12 pin 10 pin v.
Attach all 4 Damping Elements next to the holes (marked) Find and mark the Mounting Position (below the open side of the net, see above.) Place the SILVERsensor in the Mounting Position. Mark the intended position of the Mounting Screws. Screw in the Mounting Screws with a screwdriver.
Page 19
Insert and Turn Connect the SILVERsensor Cable to the SILVERsensor. 2. Insert the SILVERsensor Cable into the “HS” port of the Control Box, then put the Control Box back into the Net. 3. Re-attach the Base Platform using the Platform Screws...
Safety WARNING Risk of injury through crushing The SILVERsensor App allows you to move the Bed Frame continuously. There is a risk of injury during continuous movement. To avoid this, ensure that: • The Bed is in clear vision during continuous movement •...
Page 21
Home Screen These buttons are required to pair the App and change position. Instructions for other functions are available in the App Tutorial. Settings Menu Head Platform Adjustment Button Foot Platform Adjustment Button Personalizable Memory Positions Pre-set Memory Positions SILVERsensor Manual...
Page 22
Pairing mode lasts for 120 seconds. 3. Go to the Settings Menu and tap “Connect to SILVERsensor”. 4. Tap on your SILVERsensor from the list of available devices. 5. Wait for pairing to complete. Moving the Bed Frame Up and Down Manual Movement: 1.
Frame from the mains before cleaning iii. Technical Data Technical Data for the SILVERsensor can be found in its Datasheet. iv. Disposal Before disposing of the product, check the types of materials in the SILVERsensor and make plans to dispose of them accordingly.