Table of Contents
Advertisement
Quick Links
U.S.SAWS TC-7 STAND-UP EDGER
OPERATING MANUAL
Copyright 2020, by U.S.SAWS . All rights reserved. This work may not be reproduced or disseminated in whole or in part by any
TO PREVENT SERIOUS INJURY DO NOT OPERATE SAW WITHOUTPROPER TRAINING AND.
Notice of Copyright Protection
UNDERSTANDING OF THE OWNERS MANUAL
WHEN OPERATING THIS MACHINE
means without the prior written permission of U.S.SAWS
Surface Prep
ALWAYS WEAR SAFETY APPROVED
Division
P: 877-817- 6687 F: 813-621-7125
Visit us at www.ussaws.com
sales@ussaws.com
HEARING PROTECTION
U.S. English
07-15-2020
Advertisement
Table of Contents
Related Manuals for U.S.SAWS TC-7
Summary of Contents for U.S.SAWS TC-7
- Page 1 Notice of Copyright Protection UNDERSTANDING OF THE OWNERS MANUAL Copyright 2020, by U.S.SAWS . All rights reserved. This work may not be reproduced or disseminated in whole or in part by any WHEN OPERATING THIS MACHINE means without the prior written permission of U.S.SAWS...
-
Page 2: Introduction And Specifications
& maintenance Part Number SX67000 of the TC-7 Stand-up Edger & to instruct you in safety practices for dealing with these conditions. Keep all manuals provided with your machine in a ALWAYS WEAR SAFETY APPROVED... -
Page 3: Symbols And Decals
Wear appropriate clothing chine. You must clearly understand the written instructions supplied by U.S.SAWS, be trained - including actual operation - & know the safety rules & regulations for the job site. It is a safety practice to point out & ex- plain safety signs &... -
Page 4: Safety Instructions
Do not operate this machine unless you have received operational and maintenance training from a U.S. SAWS representative or from an autho- 4.11 AVOID ANY AREAS OR ACTIONS THAT EXPOSE YOU TO CARBON rized distributor for U.S.SAWS. MONOXIDE. Exhaust gas from gasoline engines contains dangerous carbon monoxide. PROTECT YOUR FEET. - Page 5 S A F E T Y I N S T R U C T I O N S 4.18 DO NOT OVERREACH. 4.30 LOAD AND UNLOAD SAFELY. Keep proper footing and balance at all times. Use proper heavy lifting procedures. Read & understand manuals before loading &...
-
Page 6: Operation
Do not pull up with excessive pressure. The operator will be able to feel the front of the TC-7 pull to the left if too much input is applied to the Rear Pitch Control Handle. -
Page 7: Parts Breakdown
PA R T S B R E A K D O W N TC-7 PARTS BREAKDOWN ITEM QUANTITY PART NUMBER DESCRIPTION US67101 FRAME, STAND UP EDGER US67121 FRONT TOGGLE US67107 SPIRAL RETAINING RING, 1” SHAFT US31052-5 3/8” - 24 HEX NUT US60225 1/4”... - Page 8 PA R T S B R E A K D O W N ITEM QUANTITY PART NUMBER DESCRIPTION US67101 FRAME STAND UP EDGER US67102 SUPPORT LEG US67124 LEG STOP BAR SX20121 CASTER 4” WHEEL, 1/2 US31351-1 1/2” - 13 NYLOCK NUT US31337 3/8”...
- Page 9 PA R T S B R E A K D O W N ITEM QUANTITY PART NUMBER DESCRIPTION SX65807 7”G2 GRINDER - VAC SHROUD (CONVERTIBLE) SX80640 SHROUD ADAPTER, METABO/GEN 2 SHROUD US27539 5/16”- 18 X 3/8” SOCKET HEAD SET SCREW SX50501 B - CV NUT SX71100-1...
- Page 10 PA R T S B R E A K D O W N ITEM QUANTITY PART NUMBER DESCRIPTION US31337 3/8” USS FLAT WASHER US67118 HANDLE MOUNT BLOCK US67116 HANDLE ADAPTER DISC SXW24230 W24-230 9” METABO GRINDER SX20315 ELECTRICAL GROUNDING SCREW, 10-32 US67114 CORD GRIP, 3/8 NPT ALUMINUM US67117...
-
Page 11: Warranty And Service
Warranty This document is to be used as a guide in determining warranty policies and procedures for U.S.SAWS and its U.S.SAWS products. It is to be used in determining whether a warranty is justified and as a procedural guide in completing a U.S.SAWS warranty claim form. - Page 12 FILL OUT THE ATTACHED CARD COMPLETELY AND ACCURATELY. WARRANTY REGISTRATION CARD IMPORTANT! To ensure that your U.S.SAWS machine is covered under warranty, please fill in the following information and mail or fax it to U.S.SAWS, 3702 W. Central Ave. Santa Ana, CA 92704, Fax No. 714-434-7299...
Need help?
Do you have a question about the TC-7 and is the answer not in the manual?
Questions and answers