Subscribe to Our Youtube Channel
Related Manuals for Standa FBC1LD
Summary of Contents for Standa FBC1LD
- Page 1 FBC1LD - complete electronics for laser diodes for Interferometer (HeNe laser replacement) USER'S MANUAL Svitrigailos 4-39 03222 Vilnius Lithuania 2018 Rev. 1...
- Page 2 Standa makes no representation or warranty, either expressed or implied, with respect to this document. In no event Standa will be liable for any direct, indirect, special, incidental or consequential damages resulting from any defects in this documentation.
-
Page 3: Table Of Contents
3.3. Description of controller ........................- 10 - Chapter 4. Device Specifications ........................- 12 - Chapter 5. Work 5.4. Connecting Controller to PC ......................- 13 - 5.5. Getting started ...........................- 14 - Warranty ................................- 15 - Appendix A. FBC1LD device Views .......................- 16 - - 3 -... -
Page 4: Fbc1Ld
Chapter 1. Unpacking and Inspection Device FBC1LD was thoroughly tested and carefully packed at Standa in a defect free container. Upon receiving your device, immediately inspect the outside of the package. If the container is seriously damaged, please unpack your system at the presence of the carrier representative. - Page 5 YS16-1201200 - AC plug “EU” option only. *size on photo is not in scale with photo of the device GE12I05-P1J – changeable AC plugs. *size on photo is not in scale with photo of the device. - 5 -...
- Page 6 Connection kit for laser diode cable (plug DB9M and plastic casing). *size on photo is not in scale with photo of the device. Connection kit for grounding. *size on photo is not in scale with photo of the device. - 6 -...
- Page 7 USB 2.0 cable “plug mini USB – plug USB A” *size on photo is not in scale with photo of the device. - 7 -...
-
Page 8: Chapter 2. Laser Safety
Post warning signs and limit access to the laser area when the laser is in operation. NEVER LEAVE THE LASER ON, OPENED AND UNATTENDED! Standa offers protective eyewear as well as beam dumps and laser beam shutters. For more information please browse subsection Laser Safety of Laser and Laser Accessories section at www.standa.lt... -
Page 9: Chapter 3. Device Description
Chapter 3. Device Description 3.1. Brief introduction to the device The FBC1LD is a complete system to supply laser diode for Interferometer, containing laser diode driver, temperature driver and controller. Fig.1 Image of the FBC1LD device - 9 -... -
Page 10: Description Of Controller
3.3. Description of controller The device controller allows the laser to be monitored and controlled via the USB interface (adapter is integrated). Please look to file JLV-SOFT9_software_screenshots.docx for control software. - 10 -... - Page 11 All connectors and ports are located on the front and rear panels of FBC1LD. See the Fig. 3 for more information Fig.3 Front and rear panels of FBC1LD Connection diagram of FBC1LD is shown in Fig. 4 Fig. 4 Laser diode connection diagram example. Pin5 is reserved for optional cable screen connection to GND circuit of the device.
-
Page 12: Chapter 4. Device Specifications
USB interface is galvanic isolated from the device electronics. o Software – available user interface for Windows (from shipped media (USB Flash or CD) (if shipped) or from Standa file server) and Windows dll libraries (on request). - 12 -... -
Page 13: Connecting Controller To Pc
o Communication protocol – is open and available on request. Note: protection mechanism against unauthorized changes is included in protocol, not in software. This means that custom software also will have protection mechanism against unauthorized changes. Protections: o Laser diode Driver output voltage will be switched OFF in case of laser diode is disconnected. -
Page 14: Getting Started
5.5. Getting started During initial investigation of functionality of controller and software, do not connect laser diode to the controller. It is recommend to familiarize with the controller by using equivalent circuits – resistor 10ohm 2W - instead of real laser diode, some small Peltier element 11x12mm coupled with NTC resistor 10k B25/85=3977 (for example), or resistor 10ohm 2W instead of Peltier element, or fixed value resistor 10k - instead of NTC resistor. -
Page 15: Warranty
Warranty Standa device FBC1LD is guaranteed to be free from defects in material and workmanship for a period of 6 months after delivery. STANDA does not assume liability from installation, labor and consequential damages. - 15 -... -
Page 16: Appendix A. Fbc1Ld Device Views
Appendix A. FBC1LD device Views - 16 -...
Need help?
Do you have a question about the FBC1LD and is the answer not in the manual?
Questions and answers