Advertisement
Quick Links
Instructions for LOSB9601 DC Nitro Peak 3-Way Charger
Instructions for LOSB9601 DC Nitro Peak 3-Way Charger
4A LED
1A LED
Red "BEC" Plug
White Tamiya Type Plug
Features:
• Advanced Low Delta Peak Detection Circuit
• Automatic Trickle Charge
• C harges 1-cell Igniter, 4 - to 5-cell, or 6- to 7-cell NiCd
and NiMH Packs
Specifications:
• Input: 11.5 – 15V DC
Operation:
1. C onnect alligator clips (Red to +, Black to - ) to 12-volt car battery (car must NOT be running) or 12V power source.
The LEDs will blink followed by a beep and the 1A LED staying lit. If this does not happen immediately the charger is
connected backwards.
2. Choose item to be charged: glow igniter, receiver battery, or 6- to 7-cell Sub C battery pack.
3. Attach a SINGLE item into the correct charger lead/plug type. (Never try to charge two items at the same time.)
• Large WHITE Tamiya-type—(4A) for 6- to 7-cell Sub C pack.
Start/Stop Button
Hex Igniter Plug
Black (-) Input Lead
Red (+) Input Lead
• Automatic Battery/Charge Rate Detection
• S imple Operation with LED and Beeper Status
Notification
• Built in MOSFET and PTC Fuse Protection
• Output: 1–4 Amps (NiCd & NiMH Batteries Only)
1
• Small RED BEC-type—(1A) for 4–5-cell receiver pack.
• Metal hex—(1A) for 1-cell Glow Igniter.
4. When the single connection is made the 1A LED will blink and a single beep will sound.
5. P ress and hold the start/stop button 2 seconds—three (3) beeps will sound, the charger will detect the number of cells
and the LED for the correct charge rate will light.
6. W hen the battery is charged there will be eight (8) beeps and the LED will blink as the charger goes into Auto-Trickle
mode. A beep will sound once every minute until the battery is removed.
7. W hen charging a 6- to 7-cell battery using the Tamiya-type plug the charger will detect the pack voltage (cell count)
automatically. The charge rate will be 1A at first if the battery voltage is low. It will check again one minute later and
if the voltage is still low an error alert will make the beeper sound and LEDs flash. Check to make sure you have the
correct connection. If not make the correct connection and restart. If the connection is correct restart—if the error alert
sounds again the battery is probably damaged.
8. T o stop charging or change items to be charged press the start/stop button until three (3) beeps sound. A long beep will
sound and the LED will start flashing. It is now safe to change the battery you wish to charge. NEVER change the item
to be charged without stopping the charging of the previous item first — even if they are the same type.
WARNINGS:
• Always make sure the battery pack (+) is connected to the charger output (+).
• N ever plug another battery in to be charged until you remove the previous battery, the charger stops and the beeper
sounds three times.
• Never connect more than one battery to the charger at the same time.
• T he 1A circuit has PTC fuse protection. If you should try to charge a 1-cell glow igniter without resetting it, the charger
will automatically shut down and go to stand-by mode.
2
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Team Losi LOSB9601
Summary of Contents for Team Losi LOSB9601
- Page 1 Instructions for LOSB9601 DC Nitro Peak 3-Way Charger Instructions for LOSB9601 DC Nitro Peak 3-Way Charger • Small RED BEC-type—(1A) for 4–5-cell receiver pack. Start/Stop Button 4A LED 1A LED • Metal hex—(1A) for 1-cell Glow Igniter. Hex Igniter Plug Red “BEC” Plug Black (-) Input Lead Red (+) Input Lead White Tamiya Type Plug Features: • Automatic Battery/Charge Rate Detection...
- Page 2 (in accordance with ISO/IEC 17050-1) If this Product needs to be inspected or repaired, please call for a Return Merchandise Authorization (RMA). Pack the Product securely using a sions of the European EMC Directive 2004/108/EC: shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional No. HH20091108 protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until EN55022 Radio disturbance characteristics it arrives and is accepted at our facility. A Service Repair Request is available at www.horizonhobby.com on the “Support” tab. If you do not have EN55024 Immunity characteristics Product(s): LOS DC Nitro Peak Charger internet access, please include a letter with your complete name, street address, email address and phone number where you can be reached EN 61000-4-2 Electrostatic discharge immunity test Item Number(s): LOSB9601 during business days, your RMA number, a list of the included items, method of payment for any non-warranty expenses and a brief summary Equipment class: of the problem. Your original sales receipt must also be included for warranty consideration. Be sure your name, address, and RMA number are Signed for and on behalf of: clearly written on the outside of the shipping carton. Horizon Hobby, Inc. Champaign, IL USA Warranty Inspection and Repairs Nov 08, 2009 To receive warranty service, you must include your original sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your Product will be repaired or replaced free of charge. Repair or replacement decisions are at the sole discretion of Horizon Hobby. Non-Warranty Repairs Steven A. Hall Should your repair not be covered by warranty the repair will be completed and payment will be required without notification or estimate of the Vice President expense unless the expense exceeds 50% of the retail purchase cost. By submitting the item for repair you are agreeing to payment of the repair International Operations and Risk Management without notification. Repair estimates are available upon request. You must include this request with your repair. Non-warranty repair estimates...
Need help?
Do you have a question about the LOSB9601 and is the answer not in the manual?
Questions and answers