Advertisement
Available languages
Available languages
Remote Control Features and Settings
10 . SWING UP/DOWN
Press the SWING UP/DOWN button to choose the position of
the horizontal airflow louvers.
Status display of air flow
COOL/DRY:
HEAT:
NOTE:
• It is advisable not to keep the horizintal air flow louver in the
downward position for an extended period of time in COOL or
DRY mode. This may cause condensate water to form on the
louver.
• When turning the unit on, the remote control will automatically
return the louver to the previous set swing position. When
turning the unit off, the louver will rotate to the full open
position prior to closing.
11 . SWING SIDE/SIDE Button (select models)
Press the LOUVER SIDE/SIDE button to choose the position of
the vertical airflow louvers.
Status display of air flow
COOL/DRY/HEAT/FAN
NOTE:
• When the humidity is very high, the condensate water may occur
on the air outlet if all vertical louvers are adjusted too far to the
left or right.
• When turning the unit on, the remote control will automatically
return the louver to the previous set position.
12 . DISPLAY
Turns on and off the indoor display. Press the DISPLAY button 10
times within 5 seconds to display the ambient temperature. The
indoor will beep 2 times when the setting is successful. Press
the DISPLAY button 10 times within 5 seconds again to display
the setting temperature. The indoor will beep 4 times when the
setting is successful.
The default display temperature is the setting temperature.
13 . SLEEP
Press the SLEEP button, the heat pump will operate the sleep
function, the display light will be turned off after 20 seconds. the
control logics are as following running in different mode.
1. COOL or DRY modes
One hour after SLEEP mode begins, the temperature
setpoint will increase 1°F (0.5°C). 2 hours after beginning
sleep mode the setpoint will increase 1°F (0.5°C). Seven
hours after beginning sleep mode, the setpoint will decrease
1°F (0.5°C). At the eighth hour the unit will be back to the
original setpoint. This feature helps with achieving maximum
efficiency and comfort while you sleep. See the image below.
SLEEP operation starts
℉
Rises 1℉
Rises 1℉
temp.setting
1h
2h
In COOL, DRY mode
6
Decrease 1℉
Decrease 1℉
Unit stop
7h
8h
2. Heat Mode
One hour after SLEEP mode starts, the setting temperature
will decrease 2°F. After 2 hours later, the setting temperature
will decrease additional 2°F. after 5 hours,the setting
temperature will increase 1°F, after 8 hours, the unit will run
according to the initial setting temperature, this feature helps
with achieving maximum efficiency and comfort the your
feeling while you sleep.
SLEEP operation starts
℉
temp.setting
Decrease 2℉
1h
2h
3. AUTO mode
the unit operates in corresponding sleep mode adapted to the
automatically selected operation mode.
NOTE:
•
When the unit is set to sleep mode, the fan speed will be
set to low speed and cannot be changed.
•
When the TIMER function is set, the sleeping function
cannot be set. If the sleeping function has been set and
the user sets the TIMER function, the sleeping function will
be canceled and the unit will be set to the timer function.
14 . FOLLOW
Press the FOLLOW button, the air will follow the body no matter
people stand or moving. See chart below.
Model
Detect Area
FOLLOW Detect person
in single zone
Detect person
in multi zones
Detect
nobody
15 . SURROUND
Press the SURROUND button. The air will surround the body no
matter whether people are standing or moving. See chart below.
Model
Detect Area
SURROUND Detect
person in
single zone
Detect
person in
multi zones
Detect
nobody
Decrease 2℉
Rises 1℉
7h
8h
In HEAT mode
Louver Up/
Louver Left/
Down
Right
Remote setting
Swing in the
position
direction of the
person
Remote setting
Swing
position
automatically
Keep the initial
Keep the initial
setting position
settings position
Louver Up/
Louver Left/
Down
Right
Remote
Keep the initial
setting
setting position
position
"Health airflow
Swing
(up) in cooling
automatically
mode
Health airflow
(down) in
heating mode"
Keep the
Keep the initial
initial settings
settings position
position
49-5000489 Rev. 1
Advertisement
