Advertisement
Quick Links
Manufacturer of Christie Glasshouses and Sheds
INSTRUCTIONS FOR ASSEMBLY
2355mm x 4665mm Workshop
1 Thomas Burns Street, Dunedin
Phone (03) 477 7909 www.allans.co.nz
F:\C - E\Christie Garden Products\Sheds\Shed 2355 x 4665\Shed 2355 x 4665 Assembly Instructions Rev 1.docx
Advertisement
Related Manuals for ALLAN'S Christie Jumbo Workshop 2346
Summary of Contents for ALLAN'S Christie Jumbo Workshop 2346
- Page 1 Manufacturer of Christie Glasshouses and Sheds INSTRUCTIONS FOR ASSEMBLY 2355mm x 4665mm Workshop 1 Thomas Burns Street, Dunedin Phone (03) 477 7909 www.allans.co.nz F:\C - E\Christie Garden Products\Sheds\Shed 2355 x 4665\Shed 2355 x 4665 Assembly Instructions Rev 1.docx...
- Page 2 Congratulations on your purchase of a quality Christie shed. All the parts required for building your shed are included in the pack you received. Optional extras include: Concrete base fixing brackets • Timber frame to concrete pad fixing brackets • Shelving brackets •...
- Page 3 Starting in one corner, place one of the Rear Walls and the Left Wall on the base, with the corners overlapping. Line up the holes in the corners of the two panels and bolt together. There are four bolts per corner. Overlap the corners so that the panel edges are not visible from the front of the shed.
-
Page 4: View From Rear
Repeat the process for the other Rear Wall and Right Wall. Start by overlapping the two panels at the bottom, pushing them together until the cappings butt up against each other without a gap. Use a 4” nail or nail punch through one set of bolt holes to pull the panels into alignment and bolt through the other set of holes. - Page 5 Bolt the Left Hand and Right Hand Fronts to the Walls. Left Hand Front Right Hand Front Join the Left Hand Front and Right Hand Front together with the Door Lintle at the top. Door Lintle Door Lintle F:\C - E\Christie Garden Products\Sheds\Shed 2355 x 4665\Shed 2355 x 4665 Assembly Instructions Rev 1.docx...
- Page 6 Attach the Door Guide at the bottom of Left Hand and Right Hand Front panels. Ensure the doors sit within the guide as shown, and attach the Door Guide at the ends. Door Door Guide Bolt at both ends Bolt the Ridge Arch across the middle, bolting to the top of the Front Wall and sitting over the edge of the Rear Wall.
- Page 7 Bolt the two Ridges across the middle, attaching to the Ridge Arch and the top of the Side Walls. Drill through the brackets, Rear Wall and Front Wall as shown and bolt Ridge Arch to inner face of Rear Wall. Drill through this bracket and Walls.
- Page 8 Attach the Spouting as shown. Roof Roof Panel Panel Spouting Ridge Rear Wall Drop bolts through holes in top first, then tilt Spouting and tighten. Bolt bottom afterwards Bolt to Ridge F:\C - E\Christie Garden Products\Sheds\Shed 2355 x 4665\Shed 2355 x 4665 Assembly Instructions Rev 1.docx...
- Page 9 Assemble the Doors by sliding the wheels at the top of each Door into the Door Rails. Ensure the Doors are assembled such that the handles meet in the middle when the Doors are fully closed. Fasten a bolt and nut in four places in the Door Rail as shown to act as a Door Stop and limit the door movement.
- Page 10 Join the Left Flashing and Right Flashing with the Flashing Joiner in the centre. Repeat to make the other Side Flashing. Fit the Side Flashings OVER the roof panel, but INSIDE the Spouting. Bolt these through the Roof Panels and Side Walls.
- Page 11 Fold the fixing tabs on the Ridge Covers so they point straight down as shown. Drop the tabs through the gap in the centre of the Ridge and push the ends of the Ridge Covers hard up against the sides of the shed. Fold the tabs up inside the shed to hold the Ridge Covers in place.
- Page 12 Timber Base: Hammer a piece of 50mm x 50mm timber to the timber frame directly under the door opening to strengthen the door guide. Use at least three self-drilling screws to drill through the top of the door guide into the 50mm x 50mm timber as shown.
- Page 13 Timber Base: Nail the shed to the timber base. Nail all panels to timber Timber Base on Existing Concrete Pad: Fix brackets to timber. Fix brackets to existing concrete with suitable masonry fasteners. Fix bracket to timber Fix bracket to concrete F:\C - E\Christie Garden Products\Sheds\Shed 2355 x 4665\Shed 2355 x 4665 Assembly Instructions Rev 1.docx...
-
Page 14: View From Top
Timber Base: Nail floor slats to the timber base. Floor slats sit this way VIEW FROM TOP Left Right Wall Wall Front Your Christie Shed is now complete and ready for years of service. F:\C - E\Christie Garden Products\Sheds\Shed 2355 x 4665\Shed 2355 x 4665 Assembly Instructions Rev 1.docx... - Page 15 F:\C - E\Christie Garden Products\Sheds\Shed 2355 x 4665\Shed 2355 x 4665 Assembly Instructions Rev 1.docx...
- Page 16 Full warranty terms and conditions available by visiting www.allans.co.nz F:\C - E\Christie Garden Products\Sheds\Shed 2355 x 4665\Shed 2355 x 4665 Assembly Instructions Rev 1.docx...