ADTEK CS2-CT Manual

CS2-CT MULTIFUNCTION Counter

DESCRIPTION

The CS2-CT provides high speed and multifunction, counting,
control and communication (Modbus RTU mode) of Pulse from flow
meter or encoder, proximity switch, photo switch for length control.
There are 3 external control input (DI) in standard and the optional 4
Relay, 1 Analogue, 1 Pulse and RS485 port available. They are also
support N, R, C mode for totalizer control.

FEATURE

●
Measuring Pulse 0.01Hz~20KHz(optional: over 20KHz~50KHz); Contact / NPN / PNP / Voltage Pulse can be
switch on rear of meter
●
4 banks pre-set for all relay functions relative 4 difference application, and selectable by 3 External Control
Inputs(E.C.I.) or front key in optional
●
4 relay can be individual programmed for N/R/C mode and energized time.
●
3 external control input can be individual programmed for Reset, Gat
●
Analogue Output and RS485(Modbus RTU mode) available in option
●
Comply to CE standard & RoHS

ORDERING INFORMATION

CS2−CT−
Input Range
CODE INPUT RANGE
C
N
P
Input mode and level V
can be changed by
05
dip switches on rear
12
of meter
24
O xx

TECHNICAL SPECIFICATION

Input
Input Frequency Input Mode
0.01Hz ~ 50 Hz Mech. Contact
NPN
0.01Hz ~ 50 Hz
PNP
0.01Hz ~ 100KHz
0.01Hz ~ 140KHz Voltage Pulse
(optional)
Pick Up Sensor
Input Mode(NPN, PNP, Contact) & Level(5Vp, 12Vp, 24Vp) changeable
by dip switch of rear terminal block.
Input range: 0.01Hz~20kHz (~50kHz in option)
Sampling time: 0.05 m-second~100 seconds (0.02 m-second in option)
Response time: ≤100 m-sec.(when the AvG = "1") in standard
Display & Functions
LED: Numeric: 5 digits, 0.8"(20.0mm)H red high-brightness LED
Relay output indication: 4 square red LED
RS 485 communication: 1 square orange LED
E.C.I. function indication: 3 square green LED
Display range: 0.0000~99999 with auto moving of decimal point
Factor Setting:
Settable Range: -19999~+99999 with decimal point
settable 0 / 0.0 / 0.00 / 0.000 / 0.0000
Decimal Point:
Settable: 0 / 0.0 / 0.00 / 0.000 / 0.0000
Overflow ovfl/ Re-cycle rcycl counting programmable
Over Flow indication:
Compensation setting: Option: Settable range: -19999~+99999
Digital adjustment: Option: cTspn: Settable range: -19999~99999
Control Functions(option)
Four set-points
Set-points:
Control relay: Four relays
Relay 2 & Relay 3: Dual FORM-C, 5A/230Vac, 10A/115V
Relay 1 & Relay 4: Dual FORM-A, 1A/230Vac, 3A/115V
− Relay − Analogue −
RS 485 Port
Output Output
OPTION OPTION OPTION
CODE REALY O/P CODE ANALOG O/P
N
Mech. contact None
NPN R2 2 Relay
R3
PNP 3 Relay
Voltage pulse R4 4 Relay
* If the pulse output is
5V pulse
to be selected, the
12V pulse
meter can be
24V pulse
selected 3 relay
Specify maximum.
Input Level
High Level: 8~12V; Low Level: 0.0~4.0 V
(with excitation supply 12Vdc)
High Level: over 2/3 of input level
Low Level: under 1/3 of input level
Specified by order
CS2-CT-2010-10-03
− Pulse − AUX.
Output POWER
CODE RS 485 PORT
N N
None None
0(1) ~ 5 V 8 RS 485
V
0 ~ 10 V
0 ~ 10 mA
I
0(4)~20 mA
Energized mode:
Banks pre-set:
External Control Inputs(ECI)
Input mode:
Functions:
Debouncing time:
Analogue output(option)
Accuracy:
Ripple:
Response time:
Isolation:
Output range:
Output capability:
Functions:
Digital fine adjust:
(Pulse input)
CODE PULSE O/P CODE AUX. POWER
N A
None AC 115/230 V
C Open Collect
OPTION 4
R
Relay Contact AC 85~264V
ADH
DC 100~300V
ADL AC/DC 20~56V
N / R / C Mode
Period of Relay on: 0:00.0~9(Minutes):59.9(Second)
DO function: Energized by RS485 command of master.
4 banks pre-set for all relay functions to relative 4
difference control condition, and selectable by 3 External
Control Inputs(E.C.I.) or front key
3 ECI points, Contact or open collect input, Level trigger
Gate / Reset / Offset / Bank selection(option) programmable
Settable range 5 ~255 x (8m seconds)
≤± 0.1% of F.S.; 16 bits DA converter
≤± 0.1% of F.S.
≤100 m-sec. (10~90% of input)
AC 2.0 KV between input and output
Specify either Voltage or Current output in ordering
Voltage: 0~5V / 0~10V / 1~5V programmable
Current: 0~10mA / 0~20mA / 4~20mA programmable
Voltage: 0~10V: ≥ 1000Ω;
Current: 4(0)~20mA: ≤ 600Ω max
aOhs(output range high): Settable range: -19999~99999
aOls(output range Low): Settable range: -19999~99999
aOlmt (output High Limit): 0.00~110.00% of output High
aOzro: Settable range: -38011~+27524
aOspn: Settable range: -38011~+27524
C2-17
-1/8