Related Manuals for Kobelt 2048
Summary of Contents for Kobelt 2048
- Page 1 2048 Control Head Owner’s Operation, Installation & Maintenance Manual Kobelt Manufacturing Co. Ltd.
- Page 2 2048 Control Head Kobelt Manufacturing Co. Ltd. NOTES RECORD DATA BEFORE INSTALLATION FOR FUTURE REFERENCE Model #: Serial #: Date of Purchase: Date of Installation: Rev A mnl_2048.docx 2 of 21...
-
Page 3: Table Of Contents
2048 Control Head Kobelt Manufacturing Co. Ltd. Table of Contents Introduction ........................4 Contact ............................4 Safety ............................4 1.2.1 Safety Alerts .......................... 4 1.2.2 Notice to Installer ........................4 1.2.3 Product Hazards ........................5 Product Description .......................6 Overview............................ 6 Technical Data ........................... 7 Model Code Key ......................... -
Page 4: Introduction
This document is intended to clearly present comprehensive product data and provide technical information to assist the end user in design applications. Kobelt reserves the right, without notice, to change the design, or construction, of any products and to discontinue or limit distribution of any products. -
Page 5: 1.2.3 Product Hazards
Ensure that all power sources are locked out prior to performing work. Pinch Points: The 2048 control head contains pinch points, which can cause bodily harm. Ensure that hands and fingers remain clear of the pinch points when performing work. -
Page 6: Product Description
The 2048 is available in a combination of black and chrome, all black, or all polished chrome to suit your appearance preference. Accessories, such as neutral safety switch kits or throttle extension kits can be ordered with the units or as after market parts. -
Page 7: Technical Data
1) Forward direction only. 2) Force output limited by rating of the cable. Values shown are for 40 series cable. ODEL The 2048 control head can be configured in several different ways. Below is a key defining the letter code options: Rev A mnl_2048.docx... -
Page 8: Installation
3.2.1 Hardware The 2048 control head can be used with either 30 series or 40 series control cable. Kobelt Manufacturing does not recommend solid core cables. A solid core cable would consist of a single wire that is too stiff. Multi-stranded cores are more flexible and therefore generates less friction during operation. -
Page 9: Control Head Connection
It should also be noted to avoid routing the cable near sources of heat, such as exhaust pipes or cold, such as refrigerated fish holds. 3.2.3 Control Head Connection The 2048 control head has a lever mechanism for actuating the clutch and the throttle that permits the cable to be installed in either push or pull. -
Page 10: Actuator End Connection
2048 Control Head Kobelt Manufacturing Co. Ltd. To correctly install the clutch control cables, follow the steps below: 1. Secure the cables to the support bracket with the appropriate cable clamps. 2. As illustrated in the diagram below, move the control handles to the extreme forward position. -
Page 11: Electrical
Kobelt Manufacturing Co. Ltd. When connecting the actuating end of the cable to a spool valve such as the Kobelt 4605 servo cylinder, maximum cable life and efficiency is achieved when the cable is aligned with the lever in two planes. -
Page 12: Commissioning
2048 Control Head Kobelt Manufacturing Co. Ltd. OMMISSIONING NSPECTION Before putting the control head into operation, check the cable connections at each end to ensure that there is side clearance between the sleeve and the core rod and no misalignment at either the clamp or the control head which will make the cable stiff. -
Page 13: Operation
2048 Control Head Kobelt Manufacturing Co. Ltd. PERATION The Kobelt 2048 is equipped with a clutch bypass to permit operating the throttle without engaging the transmission into gear. To operate this feature, pull the handle outwards while in the neutral position and then operate the lever to the desired throttle position. -
Page 14: Recommended Spare Parts And Kits
When purchasing spare parts refer to Appendix B: Parts List at the back of this manual for Kobelt component Part Numbers. It is recommended that any required service work on a Kobelt unit be performed by a factory authorized service representative. -
Page 15: Warranty
Buyer. Kobelt’s sole obligation to the Applicant will be to repair or replace the defective part with same or similar product, to a maximum value of the list price of the product or part. The Kobelt warranty does not cover labour charges, travel or any other associated expenses. -
Page 16: Appendix A: Installation Dimensions
2048 Control Head Kobelt Manufacturing Co. Ltd. A: I PPENDIX NSTALLATION IMENSIONS Figure 18: 2048 Installation Dimensions Rev A mnl_2048.docx 16 of 21... -
Page 17: Appendix B: Parts List
2048 Control Head Kobelt Manufacturing Co. Ltd. B: P PPENDIX ARTS Rev A mnl_2048.docx 17 of 21... - Page 18 2048 Control Head Kobelt Manufacturing Co. Ltd. 2048-1000 Detent Roller Sub-Assembly Rev A mnl_2048.docx 18 of 21...
- Page 19 2048 Control Head Kobelt Manufacturing Co. Ltd. 2048-2000 Clutch & Throttle Lever Sub-Assembly Rev A mnl_2048.docx 19 of 21...
-
Page 20: Appendix C: Installation Cut-Out Template
2048 Control Head Kobelt Manufacturing Co. Ltd. 10 A C: I PPENDIX NSTALLATION EMPLATE Figure 22: Installation Cut-out Template Scale may not be exactly 1:1 due to PDF and printer scaling. Verify primary dimension with a ruler after printing and before using to cut. - Page 21 Kobelt Manufacturing Co. Ltd. 8238 129th Street Surrey, British Columbia, Canada, V3W 0A6 Sales Tel: +1-604-572-3935 Fax: +1-604-590-8313 Email: sales@kobelt.com Website: www.kobelt.com Made in Canada / Printed in Canada...