Table of contents Table of contents Security instructions ................6 Change administrator PIN ..................6 Sleep mode ......................7 General information ....................7 The Status LED..................8 Security area ..................9 What does "Activated internally" mean? ............. 10 What does "Externally armed" mean? ..............10 Switch the security area to activated/disactivated ......
Page 5
Table of contents Settings menu ................... 23 Who can access the settings menu? ..............23 Overview of access rights ..................24 Pull up the settings menu ..................24 1 Enable/disable Bypass ..................25 2 Activate the button lock ................... 27 3 Switch off the "Doorbell"...
Administrator PIN The factory-assigned Administrator PIN (0001) must be changed by the main user or main person responsible for the Alarm Connect security system the first time the system is used. If disregarded, there is a risk of misuse by unauthorised third parties.
Security instructions Sleep mode Sleep mode The control panel of the wireless operating unit changes to sleep mode after about 30 seconds. Before you want to take action (turn on the power, go to the menu or info page, trigger the alarm, etc.), you can quit the sleep mode by pressing the OK button; i.e.
Device description The Status LED Status LED 22:30 Depending on the switching condition of the security area, the colours of the status LED have the following meanings: Switching condi- Meaning tion green Everything ok Inactive yellow Fault (e. g. tampering, battery low, etc.) Alarm (e.
Security area Security area The Gira Alarm Connect security system has a maximum of four security areas. One feature of the security area is the monitoring of completed buildings or areas, each of which can be separately armed or disarmed. Unauthorised intrusion into an armed security area triggers an alarm.
Security area What does "Activated internally" mean ( "Activated internally" means that a security area is activated and people are in the security area. This corresponds to the so-called perimeter monitoring. Internal activation takes place, for example, on the wireless operating unit within the security area.
Detailed information on the topic of "alarm forwarding" and "remote alarming" can be found in the system description of the Alarm Connect security system. Switch the security area to armed/disarmed...
Arm/disarm I am at home - switch on "internally arm" 1. Press the key and enter the user PIN. 3 PIN correct: The symbol appears on the Display and the button lights up constinously yellow. The security area is switched to "Internally armed". You can now move freely in the security area.
Arm/disarm I am not home - Activate "Externally armed” Activate "Externally armed" with the gateway function 1. Press the key and enter the user PIN. 3 PIN correct: The symbol appears on the display and the exit delay is activated. 2.
Manual alarms Manual alarms Trigger alarm Requirement: The alarm types have been activated and configured in the project. The following alarms can be manually triggered using a three-digit code on the wireless operating unit: • Panic alarm (factory code: 110) •...
Manual alarms When do I trigger the panic alarm? Trigger the panic alarm if you are in the security area and there is sudden dan- ger (e. g. from an intruder). When do I trigger the fire alarm? Trigger the fire alarm if you detect a fire and can not extinguish it yourself. The fire alarm alerts all other people in the security area.
Information page Information page On the information page, all current messages (alarms, faults, etc.) are displayed according to the following priority: • Messages from another security area • Messages about active faults that need to be cleared. • Messages about ignored faults that must be acknowledged •...
Display Alarm messages on the display An active alarm message can only be deactivated by entering a PIN. The following alarm messages could be shown in the display: Message Meaning Intruder alarm under "Externally armed" Deactivate alarm Intruder alarm under "Internally armed" Deactivate alarm Fire alarm Ongoing fire alarm...
Display Symbols on the display Messages from the personal security area are shown on the display via the fol- lowing symbols. Depending on the message, the symbols may appear alone or in combination. Symbol Meaning Alarm device open By pressing the button, the open detectors are displayed on the info page Alarm device open with Bypass...
Page 19
Display Symbol Meaning Fault or technical message An active fault or technical message is available or the message must be acknowledged on the info page. In addition, a signal tone (every 60 sec.) can be heard. Deactivate the signal tone by pressing any key.
Page 20
Display Device monitoring alarm Check if the device is available and within range of the control unit or the wireless repeater. The batteries might be dead. Contact the profes- sional company. Messages from another security area Messages from other security areas are only shown in the display when alarm forwarding is activated.
Replacing the battery Change the batteries in the wireless operating unit WARNING Explosion hazard in case of improper handling of batteries. Do not throw batteries into the fire, and do not recharge batteries, as this may result in a risk of explosion. Replacing the battery Replace the battery as soon as the "low battery"...
Page 22
Replacing the battery 3. Only use new and unused batteries of the same type. Observe polarity! 22:30 4. Attach the wireless operating unit to the mounting frame (attach from above and screw on from below) until you hear a click. Acknowledge all messages on the info page.
Installer's temporary activation The "installer" is required for the duration of the installation and maintenance of the Alarm Connect security system. For safety reasons, the installer must be activated by the administrator on the wireless operating unit (normative specification). Deactivation of the installer takes place automatically when the security area is armed.
Settings menu Overview of access rights Administrator Installer User 1 Bypass* 2 Button lock 30 seconds 3 Display brightness 4 Doorbell* 5 Service info* 6 Event memory 7 Extended menu 7.1 Date and time 7.2 Time display on the operation unit 7.3 Volume 7.4 Backlight...
Settings menu 1 Enable/disable Bypass When is the "Bypass" function required? The "Bypass" function is always required if you want to switch the security area to "armed" despite the detector being open or the presence of an active fault message. The example of a wireless magnetic contact on the roof window of a bedroom shows how you can activate Bypass and then arm the security area.
Page 26
Settings menu 5. With the key, select "Bypass activated" and press ok to confirm. The following display appears: Bypass Skylight Bedroom Bypass activated Repeat steps 4 to 7 for all devices or messages that are preventing arming. 6. Press the key to exit the menu.
Settings menu 2 Activate the button lock Button lock The button lock is used, for example, when the user wishes to clean the surface of the wireless operating unit, e.g. with a damp cloth, without accidentally pressing a button. The button lock is automatically disabled after 30 seconds. 1.
2. Press OK and open the menu item. Here you'll find contact information of the professional company that installed the Alarm Connect security system. 6 Pull up all saved events The event memory stores the last 250 events (alarms, fault messages, faults, etc.).
Extended menu 7 Pull up the extended menu 1. Pull up the settings menu and press the key to navigate to menu item "extended menu". 2. Press the OK button and pull up the extended menu. 7.1 Change the date and time Changing the date and time The date and time can only be permanently changed on the wireless operating unit if this function has been activated in the GPA (Alarm system ->...
Extended menu 7.3 Change the volume of the signal tones Signal tones on the wireless operating unit The volume of the signal tones for the following functions can be set on the wireless operating unit: • Alarms • Note and acknowledgment (entry and exit delay/positive and negative acknowledgment/fault message) •...
Extended menu 7.4 Change the switch-off delay of the backlight/permanently switch on or off the display 1. Pull up the extended menu and press the key to navigate to the submenu "Backlight". 2. Press OK and open the menu item. Press the key and select one or both of the submenus.
Extended menu 7.5 Assign, change or reset the user PIN and deactivate or activate users The stored user names are shown in the submenu "User management". Assign or change user PIN The following users need their own four-digit PIN: • The Administrator. •...
Extended menu 7.6 Deactivating or reactivating the wireless hand-held transmitter Requirement: at least one wireless hand-held transmitter is connected to the Alarm control unit Connect). 1. Pull up the extended menu and press the key to navigate to the submenu "Device management"...
Activate and deactivate the test mode Detailed information on the topic of "test mode" can be found in the system description of the Alarm Connect security system. 1. Disarm all security areas. 2. Remove the housing cover (see BDA of the alarm control unit Connect). The tamper alarm is triggered.
What to do if ... What do you do if... the PIN is not accepted when the PIN is assigned? When the PIN is assigned, only 4-digit PINs may be assigned that are not yet assigned in the system. The PIN might already be taken. Select another PIN..
Connect provided to the licensee by the licensor. Namely, this comes to include the installation and update tools software as well as the provided written or electronic documentation. This software for Gira security system Alarm Connect (also subsequently referred to as Alarm Connect) will be preinstalled on the units for the licensee.
Page 37
The Alarm Connect Software contains open source software components (hereafter referred to as „OSS“). An overview as to the included OSS in the Alarm Connect software is documented in Part II of this document and the complete license text is included in Part III.
Page 38
2.4 The licensee is not permitted to transfer Alarm Connect Software with or without payment without the consent of the licensor. The licensee agrees to use the Alarm Connect Software solely for the purpose of the right of use within this usage license.
Page 39
4.1 The Alarm Connect Software and the documentation (either provided in printed form or, as well, as online documentation) will be provided to the licensee as amended. The period of the guarantee for the Alarm Connect Software is 24 months. Guarantee compliance will be performed through the sending of a replacement.
Page 40
6 Data Protection Through conclusion of these license agreements, you agree to the validity of Gira’s data protection notices in its valid version respectively.
Page 41
Licence agreement 7 Applicable Law und Jurisdiction This contract is subject to the laws of the Federal Republic of Germany under exclusion of the UN Convention on Contracts for the International Sale of Goods (CISG). This choice of law enables the consumer the application of the law of country of the consumer’s habitual residence;...
Page 42
Licence agreement II. List of Open Source Software in Gira security Alarm Connect Software Software package Source License type version avahi 0.6.31 http://www.avahi.org/download LGPLv2.1+ boost 1.65.1 http://downloads.sourceforge.net/project/ BSL-1.0 boost/boost/1.65.1 busybox 1.23.2 http://www.busybox.net/downloads GPLv2 bzip2 1.0.6 http://www.bzip.org/1.0.6 bzip2 license codesynthesisxsd 3.3.0 https://downloads.ise.de...
Brief overview — Menu Brief overview Settings menu Function must be activated Settings at the project. Only visible for Bypass Administrator / Installer. Settings Button lock 30 s Settings Display brightness Function must be activated Settings at the project. Doorbell Then visible for all.
Brief overview — Extended Menu Extended menu Extended menu Date and time Date and time Change date and time Extended menu Zeitanzeige Bedieneinheit Operating unit time display Activated Deactivated Extended menu Volume Volume Alarms Volume Note and acknowledgement Volume Doorbell Volume Button actuation and PIN entry Backlight...
Page 49
Brief overview — Extended Menu Extended menu User management User management Administrator User management User Extended menu List of hand-held transmitters Device management Handheld transmitter Extended menu Test operation Test operation Activated Deactivated List of languages Extended menu Language selection Deutsch English Extended menu...
Page 50
Display and button assignment Symbol Meaning Detector open — also see page 18 Detector open with Bypass — also see page 18 and page 25 Doorbell switched off — also see page 27 Alarm — also see page 18 Fire alarm — also see page 18 Fault/Technical message —...