Subscribe to Our Youtube Channel
Related Manuals for MASSEY FERGUSON ZT29
Summary of Contents for MASSEY FERGUSON ZT29
- Page 1 Service Manual ZT29 / ZT33 Zero Turn Mower Models: ZT29 / ZT33 VISION INNOVATION LEADERSHIP QUALITY RELIABILITY SUPPORT PRIDE COMMITMENT...
- Page 2 Zero Turn Mower ZT29 / ZT33 Workshop Service Manual Find manuals at https://best-manuals.com...
- Page 3 Find manuals at https://best-manuals.com...
- Page 4 MASSEY FERGUSON ® Zero Turn Mower ZT29 / ZT33 4283357M1 CONTENTS INTRODUCTION................................. 01 GENERAL INFORMATION ..............................02 MAIN COMPONENTS ................................ 03 ENGINES..................................... 04 SPECIFICATIONS ................................05 TRANSAXLE..................................06 FRONT AXLE ..................................07 HYDRAULIC SYSTEM................................ 08 ELECTRICAL SYSTEM..............................09 MOWER DECK ................................... 10 INDEX ....................................
- Page 5 NOTES 01-ii 4283357M1 Find manuals at https://best-manuals.com...
-
Page 6: Table Of Contents
Contents ® Massey Ferguson Zero Turn Mower ZT29 / ZT33 WORKSHOP SERVICE MANUAL 4283357M1 01 - Introduction Contents Introduction ..............................01-3 To the Dealers ............................... 01-3 Replacement Parts ............................01-3 Units of Measurement ............................ 01-3 Table of Contents ............................01-3 Page Numbers ............................... - Page 7 Contents NOTES 01-2 4283357M1 Find manuals at https://best-manuals.com...
-
Page 8: Introduction
Introduction INTRODUCTION INTRODUCTION UNITS OF MEASUREMENT This service manual has been prepared with the latest Measurements are given in metric units followed by the service information available at the time of publication. equivalent in US units. Hardware sizes are given in Read the service manual carefully before doing any millimeters for metric hardware and inches for US service on the compact tractor. -
Page 9: Safety Precautions
Introduction SAFETY PRECAUTIONS The safety of the operator is one of the main concerns in designing and developing a new machine. Designers build in as many safety features as possible. However, every year many accidents occur which could have been avoided by a few seconds of thought and a more careful approach to handling equipment. -
Page 10: Signal Words
Introduction SIGNAL WORDS Safety Signs WARNING: DO NOT remove or obscure The words DANGER, WARNING or CAUTION are used Danger, Warning, Caution or Instruction with the safety alert symbol. Learn to recognize these signs. Replace Danger, Warning, safety alerts, and follow the recommended precautions Caution or Instruction signs that are not and safe practices. -
Page 11: General Safety Rules
Introduction GENERAL SAFETY RULES WARNING: An operator should not use alcohol or drugs which can affect their alertness or coordination. An operator on prescription or ‘over the counter’ drugs needs medical advice on whether or not he or she can properly operate equipment. Always keep this Operator Instruction Book with the machine. -
Page 12: Roll-Over Protective Structure (Rops)
Introduction Roll-Over Protective Structure (ROPS) ROPS are effective in reducing injuries during overturns. Overturning a mower without ROPS or with the ROPS folded down can result in serious injury or death. Operate with ROPS folded down only when conditions make this necessary. -
Page 13: Protect Yourself
Introduction Protect Yourself FIG. 5: Always wear protective clothing and appropriate safety equipment Wear all the protective clothing and personal protective devices issued to you or called for by job conditions. You may need: • A hard hat. • Safety glasses, goggles, or face shield. •... -
Page 14: General Operational Safety Rules
Introduction General Operational Safety Rules FIG. 7: DO NOT carry passengers. DO NOT permit others, especially children, to ride on the mower or on any implement or attachment connected to, or installed on mower. I3002 FIG. 7 FIG. 8: When dismounting and/or leaving the operator’s seat FOR ANY REASON, always: 1. - Page 15 Introduction FIG. 9: Keep clear of all rotating components. Be especially observant of areas of discharge, intake or other mechanical motion. D-5948 FIG. 9 FIG. 10: Keep clear of rotating blades. DO NOT put hands or feet under, or into mower with engine running.
-
Page 16: Operation
Introduction OPERATION Before operation, make sure you: Keep emergency telephone numbers for immediate access. Keep the mower properly maintained. Do not operate a machine with broken or missing parts. Make sure the maintenance procedures in this manual are completed before using the machine. Clean potentially flammable material away from engine compartment, battery, fuel, fuel tank, and operator’s station. - Page 17 Introduction FIG. 12: DO NOT bypass the starting circuit by shorting across the terminals of the starter motor to start the engine. This may cause the mower to move suddenly. Periodically check starting circuit to make sure all system components operate correctly. If the starting system does not work, consult your Dealer immediately.
- Page 18 Introduction FIG. 16: In the event of an overturn, hold the control levers firmly and keep your seat belt fastened. DO NOT attempt to leave the seat until the machine has come to rest. Always drive at a proper speed relative to local conditions and ensure that your speed is low enough for an emergency stop.
- Page 19 Introduction DO NOT operate near edge of banks. Setback distance from bank should equal, or exceed, the overall height of the bank. Be aware of what is located at the bottom of the slope. Use caution when there is water, cliffs, roads, or rocks at the bottom.
-
Page 20: Transporting The Machine
Introduction TRANSPORTING THE MACHINE The machine has not been designed to be driven on a public road. Check with the local authorities, as it may be illegal for the machine not only to travel on, but also to cross a public road. When transporting the machine on a public road, load onto a truck or trailer. -
Page 21: Electrical System
Introduction Electrical System FIG. 19: To prevent short circuits, disconnect the battery negative (-) cable from battery before making adjustments or servicing the electrical system. Battery may contain explosive hydrogen gas. Keep sparks, flames and cigarettes away. Do not attempt to open the sealed battery. Always use a voltmeter to check the state of charge. -
Page 22: Fuel System
Introduction Fuel System FIGS. 21–22: Diesel fuel is flammable and must be handled with care. Never refuel or service the fuel system on the mower indoors, while smoking or when near open flames or sparks. Never remove the fuel cap or refuel the mower while the engine is running. -
Page 23: Wheels And Tires
Massey Ferguson replacements must be used to restore your equipment to original specifications. Massey Ferguson will not claim responsibility for fitment of unapproved parts and/or accessories and damages as a result of their usage. I3027 FIG. - Page 24 Contents ® Massey Ferguson Zero Turn Mower ZT29 / ZT33 WORKSHOP SERVICE MANUAL 4283357M1 02 - General Information Contents General Information ............................02-3 Serial Number Plate ..........................02-3 General Precautions for separation and reinstallation ................... 02-4 Before Operation ............................. 02-4 Precautions to be Followed when Installing Common Parts ..............
- Page 25 Contents Replacing Transmission Oil Filter Cartridge ..................02-33 Checking Hydraulic Hose ........................02-33 Check Points - 300 Hours ..........................02-34 Replacing Engine Oil Filter Cartridge ....................02-34 Replacement of Fuel Filter ........................02-34 Changing Rear Axle Gear Oil ........................ 02-34 Check Points - 1 year ..........................
- Page 26 General Information GENERAL INFORMATION GENERAL INFORMATION Serial Number Plate FIG. 1: Location of serial number place on Zero turn mower (1) includes model name and serial number. I-10250 FIG. 1 FIG. 2: Location of serial number plate on Mower deck (1) includes model name and serial number.
- Page 27 General Information GENERAL PRECAUTIONS FOR Precautions to be Followed when Installing Common Parts SEPARATION AND REINSTALLATION Before Operation Roller or Ball Bearings Always be safety-conscious in selecting clothes to wear When a bearing is fitted in by the outer race, use an and suitable tools to use.
- Page 28 General Information O-rings O-rings must be coated with grease before installing. Installed O-rings must have no slack or twist. Installed O-rings must maintain proper air tightness. Snap-Rings Snap-ring installers must be designed so as not to permanently deform the snap-rings. Installed snap-rings must be seated securely in the groove.
- Page 29 General Information Cotter Pins (Split Pin) FIG. 5: When installed, cotter pins must be bent securely at the ends as shown. I-10254 FIG. 5 02-6 4283357M1...
- Page 30 General Information Nuts and Bolts Special bolts are installed at several locations, so be sure Other Precautions not to interchange them other bolts. Be sure not to damage any finished surfaces or parts. Bolts and nuts must be tightened to their specified torque Always refrain from forcing installation.
- Page 31 This as a preview PDF file from best-manuals.com Download full PDF manual at best-manuals.com...
Need help?
Do you have a question about the ZT29 and is the answer not in the manual?
Questions and answers
The very loud alarm sounds after running the mower for 20 minutes or so. It seems to be related to the position of the handles. Is there something I can do to remedy this? Thank you