Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for swepac PVD 2000
Summary of Contents for swepac PVD 2000
- Page 1 PVD 2000 USER MANUAL IN ORIGINAL Dok: 101503A-GB 1931...
-
Page 2: Table Of Contents
PVD2000 / PVS / PVM CONTENTS SAFETY INSTRUCTIONS ........3 OPERATION, PRECAUTIONS....3; 4; 5; 6 TRANSPORT, PRECAUTIONS......6 TECHNICAL DATA..........7 HOW IT WORKS..........7; 8 FIELD OF APPLICATION........9 PREPARATIONS AND OPERATING CONDITION............10 MAINTENANCE ..........11 PERIODIC MAINTENANCE OF MOTOR ..11 PERIODIC MAINTENANCE OF FLEXIBLE SHAFT AND POKERS ..... -
Page 3: Safety Instructions
PVD2000 / PVS / PVM SAFETY INSTRUCTIONS OPERATION, PRECAUTIONS DANGER Explosion hazard To reduce the risk of serious injury or death to yourself If a warm machine or exhaust pipe comes into or others read and understand the Safety and opera- contact with explosives, an explosion couldoccur. - Page 4 PVD2000 / PVS / PVM Never smoke when filling the fuel tank or when Work in a well ventilated area. working with the machine or servicing it. If the machine has an exhaust, direct the exhaust Only store fuel in a container that is specially so as to reduce disturbance of dustin a dust filled constructed and approved for the purpose.
- Page 5 PVD2000 / PVS / PVM WARNING Projectiles If numbness, persistent recurring discomfort, burning sensation, stiffness, throbbing, tingling, Failure of the work piece, of accessories, or even pain, clumsiness, weakened grip,whitening of the of the machine itself may generate high velocity skin, or other symptoms occurat any time, when projectiles.
-
Page 6: Transport, Precautions
PVD2000 / PVS / PVM TRANSPORT, PRECAUTIONS WARNING Trapping hazards There is a risk of neck ware, hair, gloves, and WARNING Loading and unloading hazard clothes getting dragged into or caught by rotating When the machine is lifted by a crane and similar machineparts.This may cause choking, scalping, appliance, this can lead to injury. -
Page 7: Technical Data
PVD2000 / PVS / PVM TECHNICAL DATA POWER UNIT PVD 2000 Model type , ..........Universal single type Electric Single Phase .......Double insulation, IP 34 Housing................Polyamid Power..................2300 W. Voltage ............230V or 115 V 50/60 Hz (Make sure working voltage is according with stated value on the characteristics plate). - Page 8 PVD2000 / PVS / PVM LENGTH MODEL WEIGHT (mm) (Kg) PVS 1, alt. PVS 1-32 PVS 2, alt. PVS 2-32 PVS 3, alt. PVS 3-32 PVS 4, alt. PVS 4-32 The complete poker vibrator assembled includes 3units: Proper protective equipment should be used because the acoustic power level of this machine is 92 dB according to ISO 3744 (85,5 the pressure level ISO 6081) 1Transmited vibration to the operator does not exceed 2,5 m/s of acceleration (1,45 m/s2 acc.
-
Page 9: Field Of Application
PVD2000 / PVS / PVM FIELD OF APPLICATION AND USE OF CONCRETE VIBRATOR A prerequisite for the finished floor to meet the quality requirements is to properly treat the fresh concrete. During poker vibration, concrete is submitted to vibration which will force trapped air to the surface making concrete homogeneous. -
Page 10: Preparations And Operating Condition
PVD2000 / PVS / PVM PREPARATIONS AND OPERATING CONDITION For your own safety, as protection for others, and to avoid damage to the equipment, read carefully this manual and operating guidelines. 1. Before working, be sure that the hose joint sleeve nut is properly fastened to the drive unit. Note! The drive unit must be switched off during this handling and check the correct working of all handling and safety devices. -
Page 11: Maintenance
C. Replace the housing when reach the minimum diameter. D. Replace the end cap when reach the minimum length. Note! Always use SWEPAC original parts PERIODIC MAINTENANCE OF MOTOR (Inside the drive unit) 1. Only an expert shall work on the electrical part. -
Page 12: Periodic Maintenance Of Flexible Shaft And Pokers
PVD2000 / PVS / PVM PERIODIC MAINTENANCE OF FLEXIBLE SHAFT AND POKERS 1. To do the maintenance works in the transmission and poker, firstly disconnect of the motor. 2. In all maintenance operations, original parts will be used. 3. To check the wear of the poker controlling the outside diameter and length of the poker. Replace the housing or cap when the diameter or length in the least point is less than the specified in the table according to the model. -
Page 13: Faulty Tracing, Drive Unit
PVD2000 / PVS / PVM FAULTY TRACING, DRIVE UNIT PROBLEM CAUSE / SOLUTION The drive unit is not starting 1. Make sure power is on 2. Carbon brushes defect 3. Defective switch The motor rotate but it overheats 1. Clean the air intake and output openings in the housing and/or change filter. -
Page 14: Notes
PVD2000 / PVS / PVM NOTES... -
Page 15: Ec-Declaration Of Conformity
The product complies with the following directives: 2006 / 42 / EG 2000 / 14 /EG 2004 / 108 / EG EN 500-1 EN 500-4 EN 12649:2008+A1:2011 ISO 11201 ISO 5349-2:2001 Technical documentation held by: Swepac AB, Blockvägen 3 SE-34132 Ljungby Hans Holmlund / Product Manager... - Page 16 SWEPAC AB Address Blockvägen 3, 341 32 Ljungby, Sweden, tel. +46 (0)372-156 00, fax +46 (0)372-837 41, E-mail mail@swepac.se, Internet www.swepac.se...
Need help?
Do you have a question about the PVD 2000 and is the answer not in the manual?
Questions and answers